My Orders
AS21 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The ice door wouldn't open.
2 of 3 people
found this instruction helpful.
-
Roberto from Newport News, VA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I followed the video of your repair man. Made it very easy.Thanks.
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 people
found this instruction helpful.
-
Gail from Golden, CO
- Really Easy
- Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
Light switch on door broke
3 of 6 people
found this instruction helpful.
-
Donna from Oro Valley, AZ
- Really Easy
- Less than 15 mins
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Was this helpful?
Thank you for voting!
ice despencer not running
2 of 3 people
found this instruction helpful.
-
Joseph from Whiting, IN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
repair&parts instalation was easy but troubleshutting difficult.
Was this helpful?
Thank you for voting!
Door started to sag causing it not to close correctly
2 of 3 people
found this instruction helpful.
-
Jason from Colorado Springs, CO
- Really Easy
- 15 - 30 mins
-
Socket set
Took door off refrigerator and removed worn parts and replaced the aforementioned parts, which took only a few minutes.
Other Parts Used:
Was this helpful?
Thank you for voting!
Ice Maker couldn't drop ice through the door.
2 of 3 people
found this instruction helpful.
-
Linda from Richmond, VA
- Really Easy
- 15 - 30 mins
I pulled the drive ring off of the icemaker and replaced it with the new part. Saved a $150 service call plus cost of part. It cost me a little over $11.00 and a repairman probably would have charged $30.
Was this helpful?
Thank you for voting!
broken door
2 of 3 people
found this instruction helpful.
-
Al from ocala, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
removed 4 screws, reeplaced broken ice door,
replaced 4 screws. Easy job with your site diagrams.
replaced 4 screws. Easy job with your site diagrams.
Was this helpful?
Thank you for voting!
Drive ring disintegrated
1 person
found this instruction helpful.
-
Joe from GRANTSVILLE, MD
- Easy
- 15 - 30 mins
Removed all screws on back and 4 on front. That part is easy IF you have a Torx of the right size. Slip out the ice bin a bit and replace the drive ring. Reassembly is a bit harder since some internal shift can occur -- rotate or tilt the whole assembly to get two -- I think -- screws started. No need to over tighten screws; snug is good
... Read more
enough.
Read less
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 people
found this instruction helpful.
-
Carolee from Spokane Valley, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
Soring old, need replaced. Air leaking in and melting ice
1 person
found this instruction helpful.
-
Jerlene from BERLIN, MD
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Followed included instructions. Thank you.
Was this helpful?
Thank you for voting!
No problems
1 person
found this instruction helpful.
-
Richard from PORT JERVIS, NY
- Very Easy
- Less than 15 mins
Just plugged it in
Was this helpful?
Thank you for voting!
Light rocker switch broke and refrigerator light couldn't go on.
2 of 4 people
found this instruction helpful.
-
Cathy from HOPATCONG, NJ
- Very Easy
- Less than 15 mins
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this helpful?
Thank you for voting!
Ice maker ejector arm broke into.
16 of 46 people
found this instruction helpful.
-
Mary L. from Millsboro,, DE
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed old ejector arm and installed new part.
Was this helpful?
Thank you for voting!
Ice catcher was missing from the icemaker
3 of 7 people
found this instruction helpful.
-
Charlotte from Cambridge, MA
- Really Easy
- Less than 15 mins
I removed the ice catcher from the excellent packaging, rinsed it, and placed it on the counter next to the fridge. I opened the door the the freezer and placed the ice catcher under the icemaker. I lowered the arm on the icemaker and closed the door to the freezer. Then I opened the door to fridge, took out a Guinness, popped the top,
... Read more
and sat down to savor my success.
Read less
Was this helpful?
Thank you for voting!
Light out.
1 person
found this instruction helpful.
-
Carlton from CHICAGO, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Popped out the old switch and replaced it with the one dying
Was this helpful?
Thank you for voting!