AS21 - Instructions

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull t ... Read more he connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Viewed the repair video. Removed covering. Replaced limit switch, control board, and solenoid. Very easy repair!

First I removed the two screws to remove outside cover. Then removed three screws to the ice dispenser assembly. Slipped in the new round door assembly and replaced the removed screws. No problems.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Very simple fix, remove 3 screws, two connectors to the old switch

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

The biggest problem I had was finding how to remove the old broken support. I did a google search and found the answer on your web page, grab it with pliers and rotate it 90 degrease then pull straight out. Installing the new one was even easier just do the reverse.

It is the model with the french door. I unplugged it, removed two screws at the bottom of the door, while holding the door from sliding down. Removed the door and put it on its side. Removed one screw that was holding the hinge, removed the hinge and replaced it with the new one. Put the door back on (do not forget to reinstall the shims) ... Read more .
Did the same thing on the other door. After putting the door back on readjusted the height to level the door, using height adjustment screw. Lock the door in place. It now works better then new

After going to manufacturer's web site and customer service phone, was unable to locate the correct switch in the dispenser area on the door. Your web site had the picture of the switch and it was right on and in stock. Shipping was quick and inexpensive. Repair went quick and all is well.

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

Remove (slide forward) the ice dispenser drain pad from the bottom of the ice dispenser assembly on front of the freezer door. Removing two screws (star head) at the bottom allows the ice dispenser cover to be removed. Remove 3 screws holding the ice dispenser assembly to the freezer door to gain access to the flapper. Remove and replace ... Read more the flapper and reverse the steps to reassmble.

The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and th ... Read more e new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!

Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into ... Read more trim. Plug refrigerator into wall socket.

Just as described by others that have left feedback, I removed a total of 4 hex-screws to access the door. Removed the old one and replaced the door. I resecured the front panel and it was done.
Thanks again for the great experience.