AS21 - Instructions

I removed the screws that held the control panel in place. Unplugged the wiring cable and put the control panel aside. I removed the old broken part and inserted the new part. Very easy. Put everything back together and it worked like new.

took off the covers and put in the new part and then put it back together.

I couldn't have repaired the refridgerator at all if your web site didn't have photos along side of the parts. My parts no. was destroyed. But after removing the face plate on the ice dispenser door and checking the area behind the plate, the burned part was clearly identifiable. I removed the one screw holding it and the two connectin ... Read more g wires - and pulled out the tiny switch. On your site, I entered the refridgerator number, and the parts list (300 or so parts for this model) appeared with identifying photos of each part. All it took was to order the part (and the ice door simply because it was old) and put it in when it arrived in one day! No only did I save much cash, but I left with the confidence that I knew what went wrong. It works as good as new now. Thanks!!!!!

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

Removed drive assembly end of ice bin using socket wrench to get to old ice bin drive ring. Pull drive sssembly back to get ice bin ring out of the other end of ice bin. Installed new ice bin ring and and reinstall drive assembly end.

Removed two star screws on plate, then two chute screws which allowed me to remove the chute. Then I removed the two screws which held the assembly in place, we had to pullout the assembly about three inches. (I had my wife hold that out of the way) Then I reached in behind the assembly and removed the chute door. At that point I saw that ... Read more the tab which hold it in the opening mechanism was broken off. So I reassembled everything without the chute door and put a dishcloth in the chute to keep the cold in and the heat out. (during this time we had to manually take ice out of the hopper) I then went on line to partselect.com and ordered the part. It came in 3 days and my wife and I opened it all up again, snapped the chute door in place, removed the dishcloth, put the assembly and plate back together and it works like new.

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i ... Read more s inside the refer!

follow video

Pried out the old switch and installed the new switch.

Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.

Unplugged the refrigerater from the outlet. Took off the front ice and water dispenser assembly. Disconnected the front panel from the electronic board. Removed the ice and water dispensing cone and installed the plastic/Foam insulator door between the two plastic arm frames.

First I removed the three screws in the top hinge that hold the upper right corner of the door to the body of the unit. Then I just lifted the door off of the refrigerator. I proped the door up just long enough to pull out the old pin (plastic) and put the new one in place. Next I picked up the door and set it on the new hinge, and las ... Read more t I put the three screws back into place. It has taken me about as long to type this out as it did to actually make the repair. The part was also very reasonably priced so I purchased two since this items has been replaced previously.

The repair was easy ... the big relief was finding a correct replacement for a fairly old appliance