8348B Frigidaire Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud squealing
1 person
found this instruction helpful.
-
John from Avis, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
As all others have said, without being redundant, I'd view post #1 or #2 for a good detailed set of instructions.
The primary issue I had was with the stainless steel ball bearing that was shipped with the kit. I couldn't figure out what it was used for, because when I removed the bearing carrier the ball fell out before I cou ... Read more ld see where the original one was located. The stainless ball bearing is a grounding ball, not a bearing. It goes on the exterior of the plastic bearing carrier/receiver.
Once I figured that part out, it was a piece of cake.
Took a little longer than other people's repairs, but I also put a new belt on and re-worked the exhaust duct for solid ducting versus flexible duct. fine-tuning the rigid duct work was a piece of cake with the tumbler out, since i could crawl right inside the chassis and make sure everything would line up (level legs, adjust elbows, etc)
The primary issue I had was with the stainless steel ball bearing that was shipped with the kit. I couldn't figure out what it was used for, because when I removed the bearing carrier the ball fell out before I cou ... Read more ld see where the original one was located. The stainless ball bearing is a grounding ball, not a bearing. It goes on the exterior of the plastic bearing carrier/receiver.
Once I figured that part out, it was a piece of cake.
Took a little longer than other people's repairs, but I also put a new belt on and re-worked the exhaust duct for solid ducting versus flexible duct. fine-tuning the rigid duct work was a piece of cake with the tumbler out, since i could crawl right inside the chassis and make sure everything would line up (level legs, adjust elbows, etc)
Read less
Was this helpful?
Thank you for voting!
The igniter glowed red and the gas did not come on !
1 person
found this instruction helpful.
-
stefan from alpena, MI
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench (Adjustable)
Read your article on possible repairs for different symptoms and after dis assembling and cleaning certain parts took a chance on the flame sensor, which turned out to be the culprit. Your help was a valuable tool in the repair process ! What would be the bee's knee's would be the resistance reading on the sensors that monitor the system
... Read more
for a more accurate diagnostic approach. But none the less you definitely aided in the repair of my propane gas dryer. Thank you very much ! And by the way the 3-4 day wait for the part was well worth the half price I paid versus our small town repair facility, Thanx again
Read less
Was this helpful?
Thank you for voting!
Dryer did not completely dry the clothes. It required several cycles to dry clothes.
1 person
found this instruction helpful.
-
Lester from CHICAGO, IL
- Really Easy
- 30 - 60 mins
-
Screw drivers
I unplugged the dryer and pryed open the top by inserting a screw driver in the space 1inch from the top on the side. After i opened it and lifed it up, I removed the one screw on both sides found in the inner part towards the front top. I then removed the front panel. The coils are toward the bottom left side. They are held in by a brac
... Read more
ket which is held in by 2 screws. I removed the outer screw and loosened the inner screw. ( you can remove both screws but it was not necessary).I then swumg the bracket around and was able to lift out the coils. I removed the connectors and relaced the coils. Once done I re-assembled the dryer. The problem was solved.
Read less
Was this helpful?
Thank you for voting!
Gas burner worked sometimes only.
1 person
found this instruction helpful.
-
Marek from CHICAGO, IL
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
Dryer was working, only burner was working occasionally only. So, in result the drying time was very long, and clothes were cold and still not satisfactionally dry; occasionally only it was hot. It became obvious to me that gas burner only occasionally is working. On the Internet I found some instructables, mostly on YouTube, but also on
... Read more
this site (the Burner diagram): thus I have learned that the culprit must be the two tiny ignition coils: they worked only sometimes, so it was only a jeopardy when checking them using a continuation meter (voltmeter with continuation feature). For the access to the burner combo I used a small checking door right below the large door, in front wall of the dryer. There are only two small screws which hold a small piece of metal which cover these tiny coils. However, I had to disconnect the burner from gas pipe to get better access to those screws. (Of course, I also disconnected the dryer from power and I had to disconnect those wire connections on the burner combo to get access to the burner). It works perfectly after this repair.
Read less
Was this helpful?
Thank you for voting!
Squeaking
1 person
found this instruction helpful.
-
David from PORT CLINTON, OH
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Watched Video Provided. Very Simple Repair. Asked my lovely wife to hold drum in place while replacing drive belt. She gladly complied and is back doing what she seems to love most. And no, I'm not kidding. Our washer and dryer seem to run 24/7/365. I've completed various repairs on both appliances over the last couple of years and saved
... Read more
100's of dollars thanks to this site .
Read less
Was this helpful?
Thank you for voting!
Dryer was burning clothes
1 person
found this instruction helpful.
-
toshio from canton, GA
- Easy
- 15 - 30 mins
-
Screw drivers
There was a gap between the drum and the front opening. So, we opened the top of the dryer using the putty knife. There are two clips once you find them you just have to push back on them to release the top of the dryer. Then there are two screws that hold the front of the dryer on. Once they are removed the front of the dryer just ca
... Read more
me off. The kit has glue and instructions past that point and I just followed them.
Read less
Was this helpful?
Thank you for voting!
Dryer drum upper seal worn
1 person
found this instruction helpful.
-
David from Orange Park, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First I removed power from dryer. Then I lifted the lid and removed the 2 screws holding the front onto the dryer. I then used a pair of pliers to grip the seal and help pull it off. Cleaned off old adhesive. Recommend getting GOOP BE GONE. Then apply high temp sealant onto area and place seal on top. Press firmly across it to make sur
... Read more
e it is in place. Then put it all back together and your done. Also, if upper seal is worn.recommend ordering lower seal at same time. I didn't and should have. Save yourself from doing this twice.
Read less
Was this helpful?
Thank you for voting!
load squeal
1 person
found this instruction helpful.
-
Mark from HGHLNDS RANCH, CO
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.
Was this helpful?
Thank you for voting!
Noisy
1 person
found this instruction helpful.
-
April from CARYVILLE, TN
- Really Easy
- 15 - 30 mins
-
Screw drivers
Took it apart and installed the parts. Then I threw the dryer in the trash and bought a new one.
Was this helpful?
Thank you for voting!
Just popped the part I ordered right in and it's was closing in no time !
1 person
found this instruction helpful.
-
Debra from BROOKLYN, NY
- Very Easy
- 15 - 30 mins
Just opened package and popped the part right in!
Was this helpful?
Thank you for voting!
dryer was squealing loadly
1 person
found this instruction helpful.
-
MIKE from MASSAPEQUA PARK, NY
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench set
took off face of dryer, removed drum 4 screws removed two srews holding bearing and shaft ,replaced shaft bearing and shaft . Just for preventive maintenance i replaced idleling arm and dryer belt. I lined everything up replaced drum used shop vac to clean lint and dust from all parts replaced face of dryer and boom i got a btand new drye
... Read more
r
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Rear drum bearing and belt needed to be replaced.
1 person
found this instruction helpful.
-
Antonio from LOS GATOS, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Remove top cover and front and remove drum and install a new bearing kit and new belt.
Was this helpful?
Thank you for voting!
Dryer making metal on metal noise....
1 person
found this instruction helpful.
-
James from RACINE, WI
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Just like in the video, but with a stackable washer/dryer unit, works like new now....
Was this helpful?
Thank you for voting!
read shaft and bearing wore out..screaching bad
1 person
found this instruction helpful.
-
rickey from richmond, MO
- Really Easy
- 30 - 60 mins
-
Screw drivers
I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a
... Read more
Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you
Read less
Was this helpful?
Thank you for voting!
squeel when turning
1 person
found this instruction helpful.
-
Bob from Lynchburg, VA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
lacked instructions. Internet yielded a simple paragraph. Scored real bonus when we discovered the lint build up past the internal filter was approaching catastropic level. Replaced the exhaust tube (plastic) with rigid metal and resolved to disassemble and clean dryer on 2 year cycle in future. Kit just isn't complete without detaile
... Read more
d instructions. Parts were complete and sufficient. Local codes have eliminated the plactic exhaust tube. Recommend that all old installs refit to rigid or semirigid before the fire happens!
Read less
Was this helpful?
Thank you for voting!