EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

8348B Frigidaire Dryer - Instructions

All Instructions for the 8348B
76 - 90 of 381

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door catch broken
2 of 2 people found this instruction helpful.
  • TJ from SCOTT DEPOT, WV
  • Very Easy
  • Less than 15 mins
Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!
Was this helpful?
Thank you for voting!
Clothes where getting brown stripmarks on the fabric.
2 of 2 people found this instruction helpful.
  • Jeff from Reidsville, NC
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers
After removing the front door of the unit I removed the Drum seal felt and upper felt part. Then I cleaned the metal ring with acetone to remove dirt. We you install the new parts the glue sent with the Drum Glide is enough for the task with a little left over. Now its working great.
Thanks for good part Jeff
Was this helpful?
Thank you for voting!
Dryer making horrible squeaking sound when running
2 of 3 people found this instruction helpful.
  • SHARON from SUMMERVILLE, SC
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set, Wrench set
I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I us ed a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.
Was this helpful?
Thank you for voting!
Our door catch got lost inside the dryer after the door was slammed to hard
2 of 3 people found this instruction helpful.
  • Joyce from PORTAL, GA
  • Very Easy
  • Less than 15 mins
I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package
Was this helpful?
Thank you for voting!
Latch on dryer no longer worked
2 of 3 people found this instruction helpful.
  • chris from dallas, TX
  • Really Easy
  • Less than 15 mins
So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.
Was this helpful?
Thank you for voting!
loud squeeling noise
2 of 3 people found this instruction helpful.
  • Lewis from Thornton, CO
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on th e belt tenioner pully. If the squeel goes away, you have found your smoking gun.
Was this helpful?
Thank you for voting!
Belt snapped after 13 yrs. maybe 15 yrs
2 of 3 people found this instruction helpful.
  • JOHNNY from ASHEVILLE, NC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
I raised up the top then took 4 bolts out of the front and it came off and then I slipped the belt on. Now was the fun part. I tried to put belt around the tension spring from the front of the machine. Bad mistake. So I turned the machine around and took off little plate bottom left, back side reached in and WA-LA back in commision. I too k a long brush and cleaned all I could reach and put it back together. Bingo, back in business.
And I'm 71 yrs. old.
Was this helpful?
Thank you for voting!
bearing bad and shaft broken
3 of 6 people found this instruction helpful.
  • Randall from New Roads, LA
  • Easy
  • 30 - 60 mins
  • Screw drivers
replaced bearing and shaft new belt and everything works just fine
Was this helpful?
Thank you for voting!
Dryer was snagging clothes between the drum and frame
2 of 3 people found this instruction helpful.
  • David from Auburndale, MA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Open the top of the dryer. Reach inside and remove 2 screws that hold the front in place. Detach the power cord inside where there is a connector. Remove the front of the dryer. That exposed the drum glide where all three nylon guides had worn off.

Peel off the old guide. Clean the surface with sandpaper. Use the supplied adhes ive to glue on the new guide. Use masking tape to hold it while it dried.

Reverse the first paragraph to re-install.
Was this helpful?
Thank you for voting!
Dryer squeak during tumbling, worn front drum glide
2 of 3 people found this instruction helpful.
  • Robert from Portsmouth, RI
  • Easy
  • 30 - 60 mins
  • Screw drivers
Disconnected power cord; lifted top using putty knife to open spring holds on the sides of the top; released front panel by removing screw from each side;removed old glide and glue; glued new piece in place; reconnected all parts and let dry overnight.

A caution to take care of sharp/rough edges when removing old felt and glide . Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.

Fit of new glide was straightforward and fit well to the lower felt glide..

(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)
Was this helpful?
Thank you for voting!
dryer was leaving brown marks on clothes
1 person found this instruction helpful.
  • Robert from Medina, NY
  • Easy
  • 30 - 60 mins
  • Screw drivers
there are several srcews to remove. there are some u dont have to take out but it looks like u do.ease of the front panel and remove the old drum glide,very hard to get of all the felt.check the the bottom guide before u order parts if possible(i could've replaced mine,but didnt have time to check it first).when glue back in place follow directions exact and clamp.allow glue to dry as long as u can. mine set overnight it was nice and dry(if u dont you'll be doing it all over again)replace everything as you took them off.all works great perfect fit!!
Was this helpful?
Thank you for voting!
Dryer drum stopped spinning
1 person found this instruction helpful.
  • Ron from Senatobia, MS
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
First I took the drum out of the dryer. This was an easy tear down. I had to remember 2 wires, and a belt assembly ( 2 pullies ). I removed 3 screws inside the drum to release the bearing assembly from the back. Then I went to the dryer chasis and removed the mounting bracket by removing 2 screws. I simply replaced the mounting bracket wi th the new one. This required having to use a magnet to hold a small ball bearing in place while I worked the rest of the pieces in position.I greased it up and went back to the drum. I replaced the old bearing assembly with the new one. Easy. I took the time to shop-vac the inside of the dryer. There was a lot of loose lint, candy rappers, coins, etc. Finally, I put it back together. Unfortunately, this is the forth (4th) time I've had to do this. It's cheaper than buying a new dryer. Now, I've got to fix the washer.
Was this helpful?
Thank you for voting!
Burn marks on clothes
1 person found this instruction helpful.
  • Carlis from Lexa, AR
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Opened the top of the dryer (no tools needed).
used socket set and removed the two screws (one on each side). unpluged wires from front panel, labled each (good practice).
Pulled open the front panel.
cleaned old felt off all around the front panel. Wiped down everything. while I had it opened, I vaccumed out the dryer u nderneath.
used glue provided in felt kit and glued new felt where old was.
let dry, put front panel back on ensuring that the felt was between drum and front panel.
put screws back in front panel. closed top.
Let me say that this is the third time I've done this to this dryer as it is about 18 years old.
Until the heating coils go out, this is the cheapest fix there is. :-)
Was this helpful?
Thank you for voting!
Drum making noise when running ( rear bearing )
1 person found this instruction helpful.
  • Ralph from Wisconsin Rapids, WI
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.
Was this helpful?
Thank you for voting!
Thump or clang at regular intervals while in operation
1 person found this instruction helpful.
  • Scott D from East Fallowfield, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
UNPLUGGED the dryer!!! Search this site they have instructions for many of the tasks they sell parts for... disconnect the vent hose, removed the access panel for the motor & belt (rear) (1/4 nut driver), slipped the belt off the idler pulley and motor pulley, carefully lifted the front edge of the top panel & rotated it back on the hinge s, labeled and removed the door interlock wires (2), removed 4 screws securing the top of the front panel (5/16 nut driver) (magnetic is best), removed a yellow guide also attached to the top of the front support (5/16 nut driver), rotated the top of the front panel clear of the drum opening (while supported) and lifted the front panel off the bottom guides, carefully lifted the back of the drum straight up about an inch while supporting the front of the drum, remove the drum from the opening created by removing the front panel (the belt should come out with the drum, removed the rear parts of the new bearing (atteched to teh back of the dryer) 5/16 nut driver... you will need a helper to catch the ball bearing holder on the exterior back of the dryer in the middle, unscrew the drum half of the bearing assembly from inside the drum (3 phillips head screws). I have done this several years ago and you will be amazed at how much dust and lint there is... CLEAN AND VACUUM EVERYWHERE AND THEN ALL THE PLACES YOU MISSED DONT FORGET THE VENT HOSE. Clean all of the old grease from the back of the drum and dryer. Installation is the reverse of removal. Don't forget the new grease and DON"T loose the cute little ball bearing that comes in the new kit. There are lots of sharp metal edges inside so use caution and hopefully you got a new belt since belt replacement requires all of the same steps except for the actual bearing removal.

I can attest to this system only on my model since this is the second bearing I have done.

Sure beats the cost of a new dryer!!! Thanks PARTS SELECT This is the 5th appliance I have repaired for freinds and family with parts purchased from your site.
Was this helpful?
Thank you for voting!
All Instructions for the 8348B
76 - 90 of 381