8348B Frigidaire Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No heat to dry clothes.
2 of 2 people
found this instruction helpful.
-
James from SAGINAW, MI
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
There was a lot of screws. And I cleaned everything well. The one part was bad so I replaced them all to make sure it'll last.
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud Squealing
2 of 2 people
found this instruction helpful.
-
William from Hudson Falls, NY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.
Was this helpful?
Thank you for voting!
tumbler not turning
2 of 2 people
found this instruction helpful.
-
Jorge from Buena Park, CA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
I took the front part off, then removed the old belt out and installed the new one in. Also fix the tensioner wheel (it had come off) After I posisoned / aligned the belt. Also cleaned the whole dryer with compressed air, it was really dirty and nasty, this dryer has not been cleaned in 20 years, overall I had a great experience with part
... Read more
s select, they send the parts real fast.
Tank you
Jorge Garcia, Buena park CA
Tank you
Jorge Garcia, Buena park CA
Read less
Was this helpful?
Thank you for voting!
Dryer would spin but not heat. The gas flame would only come on once, if that.
2 of 2 people
found this instruction helpful.
-
dan from bellingham, WA
- A Bit Difficult
- 1- 2 hours
-
Screw drivers
Once I found this site, with everybody's description of the problem & fix, it was pretty easy.
Pry the front of the top up using a flat screwdriver at each side. Then disconnected the dryer-controls wire bundle (dryer unplugged of course) at the connector, and unscrewed 1 screw on each side of the front panel close to the top (unde ... Read more r the controls, back-side of the panel), in order to pry the front panel off - top 1st.
With everything opened up, just unscrew the two screws on top of the burner coil. the pull off the plate, slip off the 2 coils, disconnect the wires, and install the new coils in reverse. Put it all back together and you're good!
(I replaced the drum glides too, while I was in there - just in time!)
Pry the front of the top up using a flat screwdriver at each side. Then disconnected the dryer-controls wire bundle (dryer unplugged of course) at the connector, and unscrewed 1 screw on each side of the front panel close to the top (unde ... Read more r the controls, back-side of the panel), in order to pry the front panel off - top 1st.
With everything opened up, just unscrew the two screws on top of the burner coil. the pull off the plate, slip off the 2 coils, disconnect the wires, and install the new coils in reverse. Put it all back together and you're good!
(I replaced the drum glides too, while I was in there - just in time!)
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The old drum seal top had torn off.
2 of 2 people
found this instruction helpful.
-
jeffrey from round lake heights, IL
- Easy
- 1- 2 hours
-
Screw drivers
Opened the drayer top and then removed the front panel.
Removed the bottom seal from the acr as it was warn.
Carefully scarped off the remaining bits of felt from the arc.
Applied the supplied adhesive to the top half of the cleaned arc.
Placed the seal and held in place with small spring clamps.
Let it dry for ... Read more an hour, then I repeated the process with the bottom seal.
I let it dry over night, overkill probably but I wanted it to stay.
Replaced the front with new seal and closed up the top.
It has been working well since. Thanks for stocking parts that help out homeowner's on tight budgets.
Removed the bottom seal from the acr as it was warn.
Carefully scarped off the remaining bits of felt from the arc.
Applied the supplied adhesive to the top half of the cleaned arc.
Placed the seal and held in place with small spring clamps.
Let it dry for ... Read more an hour, then I repeated the process with the bottom seal.
I let it dry over night, overkill probably but I wanted it to stay.
Replaced the front with new seal and closed up the top.
It has been working well since. Thanks for stocking parts that help out homeowner's on tight budgets.
Read less
Was this helpful?
Thank you for voting!
Lound noise inside dryer
3 of 5 people
found this instruction helpful.
-
Joseph from little Egg Harbour, NJ
- Easy
- 1- 2 hours
-
Screw drivers
1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the ... Read more open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the ... Read more open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
Read less
Was this helpful?
Thank you for voting!
The lint screen was old, rusty, and torn.
2 of 2 people
found this instruction helpful.
-
Paul from Dennis, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
This was the easiest and most inexpensive repair I ever had on a dryer. I did a search on the internet, found "PartSelect.com" searched their web site, found the part I needed (at a very reasonably low price) ordered it, received it within 2 days, opened the box, removed 2 screws from the old part, put the new part in, replaced the 2 scre
... Read more
ws, inserted the filter screen... and my wife was happy. Thank You PartSelect.com for perfect selection, ordering and service.
Read less
Was this helpful?
Thank you for voting!
Riped lint screen
3 of 5 people
found this instruction helpful.
-
Bill from Shelby, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
This was easer than, well brushing my teeth. And it took less time than that too. Really, really easy, just like I read.
Was this helpful?
Thank you for voting!
Gas flame turns off after a while, dryer keeps turning but no heat is generated.
3 of 5 people
found this instruction helpful.
-
Giuseppe from San Francisco, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Before this fix which worked beautifully, I tried replacing the flame sensor which did not work. To read that story, search under part number PS459818 (Flame Sensor). Our model is a Westinghouse, so access to the unit is a bit different than the other stories. It's a stacked front-loader sitting on top of a washing machine.
1. ... Read more Open the little front door (lower left side) by unscrewing the little screw right below it. The door will pivot and slide out vertically.
2. Disconnect the electrical main lead coming from the back of the unit (just in case).
3. Close the gas switch lever on main gas pipe coming from the back on left side (just in case).
2. Remove 2 phillips screws on top of the metal bracket holding the two coils. The screws have to be removed completely along with the bracket. It's easy, they are right in front and there is room for the screwdriver. Use a thin long one instead of one with multiple bits to better align with the screws, which are very close to the coils.
3. The two coils slide right out and are very different so it's easy to keep them straight. Remove electrical connectors before or after removing the coils (I marked the plastic on top with a sharpie to keep them in the right orientation).
4. Drop in the two new coils and reconnect them to the electrical leads.
5. Reconnect main electrical lead from back (match wire colors)
6. Reopen gas lever on gas pipe.
7. Drop in front cover at an angle, tilt vertically and put screw back underneath. Use magnetized screwdriver or a piece of scotch tape to hold the screw or it might fall off the screwdriver.
8. Voila'. It worked.
This website is great. Our dryer is a Westinghouse bought in 1991 (almost 20 years old!) and with this fix it's just like new. In 1994 we used parts bought here to fix our washing machine (Westinghouse LT350RXW1). That machine is now 15 years old and still going!
1. ... Read more Open the little front door (lower left side) by unscrewing the little screw right below it. The door will pivot and slide out vertically.
2. Disconnect the electrical main lead coming from the back of the unit (just in case).
3. Close the gas switch lever on main gas pipe coming from the back on left side (just in case).
2. Remove 2 phillips screws on top of the metal bracket holding the two coils. The screws have to be removed completely along with the bracket. It's easy, they are right in front and there is room for the screwdriver. Use a thin long one instead of one with multiple bits to better align with the screws, which are very close to the coils.
3. The two coils slide right out and are very different so it's easy to keep them straight. Remove electrical connectors before or after removing the coils (I marked the plastic on top with a sharpie to keep them in the right orientation).
4. Drop in the two new coils and reconnect them to the electrical leads.
5. Reconnect main electrical lead from back (match wire colors)
6. Reopen gas lever on gas pipe.
7. Drop in front cover at an angle, tilt vertically and put screw back underneath. Use magnetized screwdriver or a piece of scotch tape to hold the screw or it might fall off the screwdriver.
8. Voila'. It worked.
This website is great. Our dryer is a Westinghouse bought in 1991 (almost 20 years old!) and with this fix it's just like new. In 1994 we used parts bought here to fix our washing machine (Westinghouse LT350RXW1). That machine is now 15 years old and still going!
Read less
Was this helpful?
Thank you for voting!
Gas dryer wouldn't stay hot.
2 of 2 people
found this instruction helpful.
-
David from Petaluma, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I definitely would not have tried to do this had it not been for the other testimonials written here. But it sounded so easy, I had to just try it (the repair man estimated that with parts and labor, we would be looking at somewhere between $250 and $300!).
The repair itself took less than 15 min, but I spend a good deal of ti ... Read more me looking around the garage for a few screwdrivers and my socket set (me and tools don't meet too often). I could simply pry up the top cover on the dryer with my hands, then got it all the way up after removing two screws from the lint trap and undoing this really annoying wire connector thing. From there the front panel lifted off. To remove the drum, just had to release the tensonier on the belt, and it came right out. From this point it was really obvious where the replacement parts would be going. A few screws later, and I could swap the parts, and put humpty dumpty back together again.
It works!!!
The repair itself took less than 15 min, but I spend a good deal of ti ... Read more me looking around the garage for a few screwdrivers and my socket set (me and tools don't meet too often). I could simply pry up the top cover on the dryer with my hands, then got it all the way up after removing two screws from the lint trap and undoing this really annoying wire connector thing. From there the front panel lifted off. To remove the drum, just had to release the tensonier on the belt, and it came right out. From this point it was really obvious where the replacement parts would be going. A few screws later, and I could swap the parts, and put humpty dumpty back together again.
It works!!!
Read less
Was this helpful?
Thank you for voting!
Dryer drum would not turn
3 of 5 people
found this instruction helpful.
-
Ben from Weaverville, NC
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I first removed a vent cover in the back where the idler is located. With pliers I removed the tension off the spring. Next I simply slide the idler off the post. I pulled up on the top panel which opened like a clam shell. I used a flat blade screw driver to separate the front panel from the dryer so I could slide the new belt around
... Read more
the drum. I reversed the steps. All in all it was easy. It took me about 30min including cleanup.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
replace old screen
2 of 2 people
found this instruction helpful.
-
charles from nantucket, MA
- Really Easy
- Less than 15 mins
take out of box remove old screen drop in new screen
Was this helpful?
Thank you for voting!
Wire Meshing Had Broken Away From The Rubber Framing Tha Was To Hold It Together And Lint Was Bypassing The Screen And Getting Into The Vent Tube.
2 of 2 people
found this instruction helpful.
-
JOHN from NAUGATUCK, CT
- Really Easy
- Less than 15 mins
-
Screw drivers
Opened the dryer door unsrewed the two phillips holding the filter framework in place did a two second swap-out dropped the new unit into place the new unit and refastened it with the 2 screws that held the old one in place . And was drying a load of clothes within two minutes . . Thank you jg
Was this helpful?
Thank you for voting!
dryer lint screen rplacement
2 of 2 people
found this instruction helpful.
-
Frank from Las Vegas, NV
- Really Easy
- Less than 15 mins
-
Screw drivers
removed two screws - replaced lint screen replacement, TIME TO REPLACE UNIT - ONE MINUTE. What made this project a snap was the pictures and graphs( parts replace) uses to ensure you are ordering the exact screen .
Was this helpful?
Thank you for voting!
screen fell out of lint screan frame
2 of 2 people
found this instruction helpful.
-
steve from scottsville, KY
- Really Easy
- Less than 15 mins
-
Screw drivers
remove 2 screws,pull frame out. put new in. tighten 2 screws. put lint screen in
Was this helpful?
Thank you for voting!