8348B Frigidaire Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drum was not revolving
1 person
found this instruction helpful.
-
khalid from HILLSBOROUGH, NJ
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Open the back plate. Broken pulley was already out of place. Put the spring on the pulley and placed it. It took me less than 10 min
Was this helpful?
Thank you for voting!
Our Clothes Would Get Caught In Between The Drum & The Front Cover, Making Marks On The Clothes.
1 person
found this instruction helpful.
-
EDWARD from EDISON, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
I unpluged the dryer, raised the top cover up, removed 2 two screws & pulled front cover out. Removed the old seal, cleaned the area & installed the new seal. Reinstalled as new. Very, very easy.
Was this helpful?
Thank you for voting!
broken belt and pulley
3 of 7 people
found this instruction helpful.
-
John from Temple City, CA
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Socket set, Wrench (Adjustable)
First of all, I've purchased a belt from local service center that cost me more than $21 (local tax is 8.5%). But, I can not find the idel pulley assembly so I searched on the Internet and ordered from PartSelect.com.
Surprisedly, my order came just one day - they must cross-ship from local distribution that it's even faster t ... Read more han to get those in local stores (driving .. and hope they have what I want ..).
I've replaced the belt 2 days ago - it's easy with 4 screws removed to pull out the front door. The back panel is opened with 2 screws remove, and very easy to replace the pulley.
It's a heavy duty gas dryer made in 1989 and this is the third time I changed the belt and the first time to change a new pulley. I would recommend to change the idle pulley because I may not need to change the belt if I have had replaced it last time. A broken or not functional idle pulley may damage the belt in a short time.
Appliance such as gas dryer like mine will last forever with replaceable belt and pulley. I'm really happy to see a working dryer (almost 20 years old) and my wife is asking a small component for her washer .. that I think I can easily fix that too .. with the help of PartSelect search.
Hope this will help.
John
Surprisedly, my order came just one day - they must cross-ship from local distribution that it's even faster t ... Read more han to get those in local stores (driving .. and hope they have what I want ..).
I've replaced the belt 2 days ago - it's easy with 4 screws removed to pull out the front door. The back panel is opened with 2 screws remove, and very easy to replace the pulley.
It's a heavy duty gas dryer made in 1989 and this is the third time I changed the belt and the first time to change a new pulley. I would recommend to change the idle pulley because I may not need to change the belt if I have had replaced it last time. A broken or not functional idle pulley may damage the belt in a short time.
Appliance such as gas dryer like mine will last forever with replaceable belt and pulley. I'm really happy to see a working dryer (almost 20 years old) and my wife is asking a small component for her washer .. that I think I can easily fix that too .. with the help of PartSelect search.
Hope this will help.
John
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Drum stoppped spinning, motor didn't.
1 person
found this instruction helpful.
-
Allen from Cardington, OH
- Really Easy
- 1- 2 hours
-
Nutdriver
Opened the top, removed the 4 screws that held the front top the cabinet, took the front off, went after the dust with the vacuum cleaner, lifted the drum, installed the belt, put the front back on, and put the belt over the idler. Most of the time was in the cleaning.
Was this helpful?
Thank you for voting!
Squeaky drum until drum would not turn.
3 of 3 people
found this instruction helpful.
-
Doug from ODESSA, TX
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Watched on-line video, then applied those steps.
1. Pop the front of the deck loose using putty knife to depress clips;
2. Disconnect wires from light and door switch;
(Before I disconnected wires from door switch and light, I made wiring sketches to make sure I reconnected in original manner.)
3. Remove lint filter ... Read more mount screws and mount from bottom of door opening;
4. Cut drum belt with wire-cutters and removed it;
5. Remove drum support clip from top center of front panel;
6. Remove (1) screw from each side of dryer body that hold front to sidewalls, removed front panel;
7. Remove drum by lifting the rear out of the bearing, then moving it forward through the machine front;
[While I had the dryer disassembled, I thoroughly cleaned it of lint, dirt & metal filings. The metal filings were from the worn ball hitch and drum support bearing cup. I spent as much time cleaning it out as I did working on it.]
8. Stand drum on gallon paint bucket while removing ball hitch (Use a #2 drywall phillips apex to obtain sufficient seating & torque to remove and reinstall ball hitch screws at rear of drum.);
9. Have a second person hold the new ball hitch in position while starting screws, if necessary;
10. Use nut driver w/5/16" socket to remove bearing retainer & ground ball clip;
11. Install new bearing into retainer clip, insert attachment screws through the holes in both, stick grounding ball in depression on back of bearing as screws are fed through back panel;
12. Hold ground ball clip in place to start one screw, then the other & tighten with nut driver;
13. Start drum belt on motor shaft and position against tensioner pulley;
14. Feed drum through front of machine and loop belt over rear of drum;
15. Slide belt forward on drum as drum moves to rear to keep it aligned with position of tension pulley;
16. Lift rear of drum to place ball hitch on top of bearing, then press down to seat it into bearing;
17. Turn drum to ensure belt alignment, then re-accomplish steps 6 thru 1.
1. Pop the front of the deck loose using putty knife to depress clips;
2. Disconnect wires from light and door switch;
(Before I disconnected wires from door switch and light, I made wiring sketches to make sure I reconnected in original manner.)
3. Remove lint filter ... Read more mount screws and mount from bottom of door opening;
4. Cut drum belt with wire-cutters and removed it;
5. Remove drum support clip from top center of front panel;
6. Remove (1) screw from each side of dryer body that hold front to sidewalls, removed front panel;
7. Remove drum by lifting the rear out of the bearing, then moving it forward through the machine front;
[While I had the dryer disassembled, I thoroughly cleaned it of lint, dirt & metal filings. The metal filings were from the worn ball hitch and drum support bearing cup. I spent as much time cleaning it out as I did working on it.]
8. Stand drum on gallon paint bucket while removing ball hitch (Use a #2 drywall phillips apex to obtain sufficient seating & torque to remove and reinstall ball hitch screws at rear of drum.);
9. Have a second person hold the new ball hitch in position while starting screws, if necessary;
10. Use nut driver w/5/16" socket to remove bearing retainer & ground ball clip;
11. Install new bearing into retainer clip, insert attachment screws through the holes in both, stick grounding ball in depression on back of bearing as screws are fed through back panel;
12. Hold ground ball clip in place to start one screw, then the other & tighten with nut driver;
13. Start drum belt on motor shaft and position against tensioner pulley;
14. Feed drum through front of machine and loop belt over rear of drum;
15. Slide belt forward on drum as drum moves to rear to keep it aligned with position of tension pulley;
16. Lift rear of drum to place ball hitch on top of bearing, then press down to seat it into bearing;
17. Turn drum to ensure belt alignment, then re-accomplish steps 6 thru 1.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
squeaking dryer driving insane
1 person
found this instruction helpful.
-
greg from great cacapon, WV
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
First removed the top of the dryer, then the front of the dryer. Took the plate off the back left of the dryer to disengage the belt off the pulley.
Took the three screws out that hold the drum in place, of course the third screw stripped and had to use a screw remover, which didn't work, but the adjustable pliers did so then lifted ... Read more the drum out of the plastic reservoir in which the bearing laid. Next unscrewed the two bolts holding the plastic reservoir which also loosened the small metal piece on the back of the dryer where a small bearing is located. Put the new parts in, but instead of putting the larger bearing that fits in the plastic reservoir, I decided to put it on the drum first and guide it into the reservoir all at once, this worked well . Prior to that I put the new plastic piece on the inside and taped it there while holding that piece put the small metal piece with the small bearing on the back of the dryer. I'm sure it is alot easier with two people doing this part, but it worked and I didn't lose the small bearing. Next put the front of the dryer back on and then put the belt back on the pulley, then the top.
It definitely helped immensely to read how someone did this, just follow the instructions given and there you go, no more annoying squeak and also a feeling of accomplishment and thanks to the person who wrote the story on how to do this job, appreciate it.
Took the three screws out that hold the drum in place, of course the third screw stripped and had to use a screw remover, which didn't work, but the adjustable pliers did so then lifted ... Read more the drum out of the plastic reservoir in which the bearing laid. Next unscrewed the two bolts holding the plastic reservoir which also loosened the small metal piece on the back of the dryer where a small bearing is located. Put the new parts in, but instead of putting the larger bearing that fits in the plastic reservoir, I decided to put it on the drum first and guide it into the reservoir all at once, this worked well . Prior to that I put the new plastic piece on the inside and taped it there while holding that piece put the small metal piece with the small bearing on the back of the dryer. I'm sure it is alot easier with two people doing this part, but it worked and I didn't lose the small bearing. Next put the front of the dryer back on and then put the belt back on the pulley, then the top.
It definitely helped immensely to read how someone did this, just follow the instructions given and there you go, no more annoying squeak and also a feeling of accomplishment and thanks to the person who wrote the story on how to do this job, appreciate it.
Read less
Was this helpful?
Thank you for voting!
worn belt and squeaky bearring
3 of 8 people
found this instruction helpful.
-
Robert from Philipsburg, MT
- Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
remove the top and front of the dryer, then removed the idler assembly. This enabled me to rimove the belt form the drum and replace it and the idler assembly. Not difficult at all.
Other Parts Used:
Was this helpful?
Thank you for voting!
loud noise, gringing sound like dry bearings
1 of 2 people
found this instruction helpful.
-
George from Reno, NV
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers
Took front door off, top off, frunt off, removes screws holding rear bearing pivot, and then removed drum. repainted bearing surface on drum, installed parts, let paint dry for a day and reassembled.
Other Parts Used:
Was this helpful?
Thank you for voting!
Heat was intermittent
1 of 2 people
found this instruction helpful.
-
mark from santa cruz, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplug dryer.
Put up the top of the dryer at the front, remove 2 screws holding the front of the dryer to the sides and remove front of dryer. Locate ignition coil on lower left. Remove 2 screws and bracket over the two ignition coils. Replace coils and reassemble in reverse.
Everybody's happy.
Put up the top of the dryer at the front, remove 2 screws holding the front of the dryer to the sides and remove front of dryer. Locate ignition coil on lower left. Remove 2 screws and bracket over the two ignition coils. Replace coils and reassemble in reverse.
Everybody's happy.
Was this helpful?
Thank you for voting!
Lint screen was dilapidated and needed replacement.
1 of 2 people
found this instruction helpful.
-
Thomas from Norwich, CT
- Really Easy
- Less than 15 mins
I took the new screen out of the box. I removed the old lint screen from the dryer, and I put in the new screen. Real simple!
Was this helpful?
Thank you for voting!
Propane dryer would not ignite
1 of 2 people
found this instruction helpful.
-
chris from Hinesburg, VT
- Really Easy
- Less than 15 mins
-
Screw drivers
Cover of the dryer pops off and hinges back. Use a flat screw driver to pop the clips on the front sides. Two phillips head screws hold the front panel on. Remove them then lift the panel off the clips at the bottom. Two phillips head hold the Ignition Coil bracket in place. Take note of the direction of the cable connection, it's no
... Read more
t marked. Dryer would ignite intermittently. Clothes were not dry after 1 hour.
Read less
Was this helpful?
Thank you for voting!
Door catch broke and fell into dryer.
1 of 2 people
found this instruction helpful.
-
Genevieve from NORTH ANDOVER, MA
- Very Easy
- Less than 15 mins
All I had to do was pop in the new door catch. Works perfectly.
Was this helpful?
Thank you for voting!
dryer would dry for the first 5 min them make noise with no heat.
1 of 2 people
found this instruction helpful.
-
Matthew from lake villa, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
my experience was just like the other responses. top comes off, 2 screws and the front comes off and the screws to the solenoids come off. Replaced the solenoids and put everything back together.
Was this helpful?
Thank you for voting!
Lint screen had separated from frame letting lint into vent.
1 of 2 people
found this instruction helpful.
-
George W. from Wallkill, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
New screen and holder came in, removed screws holding the holder in place and reinstalled new one & dropped the screen in place.
Was this helpful?
Thank you for voting!
Dryer was putting brown spots and tearing clothes.
1 of 2 people
found this instruction helpful.
-
Angela from Runnemede, NJ
- Easy
- 15 - 30 mins
My husband took the front panel off. We scaped the old seals off. Used the adhesive that came with the drum glide and replaced both parts. No more ripped and stained clothes, that easy!
Other Parts Used:
Was this helpful?
Thank you for voting!