3976 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
There was a warm spot at the front edge of dividing wall. The fan motor was not working.
4 of 4 people
found this instruction helpful.
-
Kathrine from FORT MILL, SC
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
I followed the directions of Steve on the installation video. He makes it easy to do the repair with his step by step description of the installation. I have repaired three different aging appliances with help of Steve and PartSelect's very helpful Customer Service.
I wish Steve a wonderful retirement and hope PartSelect can find ... Read more someone as easy to follow for future videos. The videos are priceless for the repairs.
I wish Steve a wonderful retirement and hope PartSelect can find ... Read more someone as easy to follow for future videos. The videos are priceless for the repairs.
Read less
Was this helpful?
Thank you for voting!
The lights were on inside however the the water/ice dispenser did not work and the fridge and freezer side was not cooling
5 of 7 people
found this instruction helpful.
-
Rickey from DUMAS, AR
- Really Easy
- 30 - 60 mins
-
Socket set
Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugge
... Read more
d it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.
Read less
Was this helpful?
Thank you for voting!
Refrigerat
5 of 7 people
found this instruction helpful.
-
Charles from Rose Bud, AR
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
rerfrigator side not cooling After determinating that the defrost timer was running I turned it to defrost and watched tosee if frost started to melt. When it didn't I checked the heater with ohmeter, checked OK, so the only other component in the defrost system is the thermostat. Then just a matter of cutting and splicing wires and
... Read more
snapping the new thermost in place
Read less
Was this helpful?
Thank you for voting!
drawer rails were broken
4 of 4 people
found this instruction helpful.
-
samuel from FAIRVIEW PARK, OH
- Very Easy
- Less than 15 mins
-
Screw drivers
. i found this site that has a diagram of the refrigerator was able to get the right parts. it was just a matter of removeing two screws and installing the new rails. very easy
Other Parts Used:
Was this helpful?
Thank you for voting!
Refrigerator light wouldn't come on.
4 of 5 people
found this instruction helpful.
-
Daniel from Crown Point, IN
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.
Was this helpful?
Thank you for voting!
Difficulty in removing the old switch
5 of 8 people
found this instruction helpful.
-
James from Federal Way, AL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around.
... Read more
If i had ordered the replacement before and not afterwards I would have seen this before hand.
Read less
Was this helpful?
Thank you for voting!
low temp due to frost built-up on freezer coils.
4 of 6 people
found this instruction helpful.
-
alfred from petersburg, NJ
- Easy
- 30 - 60 mins
-
Screw drivers
UNPLUGGED REFRIGERATOR..
removed top shelf in refrigerator..removed back plate covering controls..removed two screws holding control housing..removed two screws holding defrost timer..unplugged defrost timer and plugged new timer in..put all parts back in place with procedure reversed..
removed top shelf in refrigerator..removed back plate covering controls..removed two screws holding control housing..removed two screws holding defrost timer..unplugged defrost timer and plugged new timer in..put all parts back in place with procedure reversed..
Was this helpful?
Thank you for voting!
cam closing washer broken
3 of 3 people
found this instruction helpful.
-
David from Elk Grove, CA
- Easy
- 15 - 30 mins
-
Socket set
I propped up the door with 2x4 and shims to be level with the freezer door. Then removed the 2 screws holding the hinge to the main unit. Then removed the 2 screws holding the cam washer to the door.
Replacement was the reverse of disassembly. Be sure to tighten screws almost tight until both pieces are located correctly then fully t ... Read more ighten. Lift up refrigerator door slightly to remove shims and wood block.
I did the replacement myself but was nervous that the door would fall off the block and shims. I recommend having another person hold the door closed during the process.
Replacement was the reverse of disassembly. Be sure to tighten screws almost tight until both pieces are located correctly then fully t ... Read more ighten. Lift up refrigerator door slightly to remove shims and wood block.
I did the replacement myself but was nervous that the door would fall off the block and shims. I recommend having another person hold the door closed during the process.
Read less
Was this helpful?
Thank you for voting!
Lower door hinge cam worn out/door dropped, not sealing
3 of 3 people
found this instruction helpful.
-
Frank from Las Cruces, NM
- Easy
- 30 - 60 mins
-
Socket set
Removed door contents to lower weight (good time to clean/disinfect door compartments), blocked and shimmed door up to correct fininished height. Removed lower hinge components (make sure shims positions are noted). Replaced w/new components and removed blocking. Easy job, should have done sooner.
Was this helpful?
Thank you for voting!
Refridgerator and freezer would not stay cold and keep getting warmer.Ice was building up behind the back panel in the freezer and blocking the airflow
3 of 3 people
found this instruction helpful.
-
Donald from Cincinatti, OH
- Easy
- 1- 2 hours
-
Screw drivers
First i unplugged the refridgerator.Then i removed the freezer shelves and the 4 screws that hold the rear panel in the freezer.Next use a heat gun or hair dryer to melt the ice from the coils making sure not to overheat anything.Be sure to place something in the bottom of the freezer to catch the water and block the hole with something t
... Read more
o keep screws from falling in there.
Next,look how the heater element wires are routed so you can get them back the same way or close.Take a picture if you want.Now remove the 2 screws on the end of each element and remove the elements.Replace both even if only one looks bad.The element wire plugs in near the top of the freezer and the thermostat clips onto a metal tube.
Next,look how the heater element wires are routed so you can get them back the same way or close.Take a picture if you want.Now remove the 2 screws on the end of each element and remove the elements.Replace both even if only one looks bad.The element wire plugs in near the top of the freezer and the thermostat clips onto a metal tube.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
coils frozen freezer 18 degrees refrigerator at 68 degrees
3 of 3 people
found this instruction helpful.
-
JAY from EVERETT, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Checked continuity of defrost timer and marked to make sure was cycling. When checked continuity of top defrost tube-it was fine but, soon as looked at bottom tube could see problem. Tube was black, no continuity, and left side of tube was separated from the rubber connector, thought obviously water entered tube during defrost and shorted
... Read more
unit and since wired in series with bottom unit not working would not allow power to reach top unit. New replacement kit simple to install-4 phillips screws hold the 2 units in place- thermostat clips to top coil and wiring runs along the coils to top with thermostat- connect 3 prong plug to existing hook up and put on cover plate with 2 cap screws and 2 phillips the job was completed, IMMEDIATE RESULTS. Suggestion- even though tubes are available separately the time to rewire into the existing harness to save couple $$ is not worth it- the other unit will have lost some continuity in comparison to new install so will have tendency to go bad quickly-spring for the difference and have piece of mind for many years to come for replacement of this part. 2 day standard shipping by ground right to door and the little woman thought I was superman of repairs. Since this model was built by GE for Sears- check on Sears was double and inquire in tech repair was double again-Part Select is quality,speed in processing and makes tight budget go the distance.
Read less
Was this helpful?
Thank you for voting!
Door would not close properly
3 of 3 people
found this instruction helpful.
-
Laurence from Dearborn, MI
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I emptied everything from door compartments.I removed the top cover of the door pivot with a phillips screwdriver. I removed the two screws that that hold the pivot bracket with a 8 mm socket. Lift the door off the bottom pivot bracket. Remove the old bottom pivot bracket with an 8mm socket and replace it with the new cam bushings.You mu
... Read more
st replace both bushings on the bottom of the door and on the bracket that mounts to the base of the body of the refrigerator. Reinstall the door and screws .The doors should be level with each other if they are installed properly.If not check the freezer door .The bushings may be worn on that door also.
Read less
Was this helpful?
Thank you for voting!
Door was squeaky and would no close
3 of 3 people
found this instruction helpful.
-
Ronald from Yuma, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver
I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and ap
... Read more
plied a little lubricant to the cam and job complete.
Read less
Was this helpful?
Thank you for voting!
Interior Light did not go on due to faulty switch
4 of 6 people
found this instruction helpful.
-
Robert from Coto de Caza, CA
- Really Easy
- Less than 15 mins
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this helpful?
Thank you for voting!
Refrigerator Water Leak
4 of 7 people
found this instruction helpful.
-
BRIGIDA from MIAMI, FL
- Easy
- Less than 15 mins
Icemaker waterline leaking inside by the grommet where the water line comes in the refrigerator . First removed the water line from grommet . Then removed grommet by hand from the fridge. Last, reversed prodedure.
Was this helpful?
Thank you for voting!