38HA Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven Temperature was 50 degrees low
2 of 3 people
found this instruction helpful.
-
Eugene from Clinton, IA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees
... Read more
low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Read less
Was this helpful?
Thank you for voting!
Replaced Broiler Element
2 of 3 people
found this instruction helpful.
-
Phillip from Reston, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.
Was this helpful?
Thank you for voting!
Oven door was locked, couldn't set oven temps
1 person
found this instruction helpful.
-
William from Nashville, TN
- Easy
- 15 - 30 mins
-
Screw drivers
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off)
... Read more
now turned off. That's a lot of things working better for less than $50!
Read less
Was this helpful?
Thank you for voting!
Element burned out, broke circle, heat only half
1 person
found this instruction helpful.
-
Michael from Thornton, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering
... Read more
the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.
Read less
Was this helpful?
Thank you for voting!
replace element
1 person
found this instruction helpful.
-
alex from huntington, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.
Was this helpful?
Thank you for voting!
Couldn't find correct drip bowls that fit.
2 of 4 people
found this instruction helpful.
-
Lowell from Hardin, KY
- Really Easy
- Less than 15 mins
Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.
Other Parts Used:
Was this helpful?
Thank you for voting!
The old drip bowls were rusting, no chrome left
3 of 7 people
found this instruction helpful.
-
kathryn from piqua, OH
- Really Easy
- Less than 15 mins
Took the old ones out and put in the new ones! What I am so pleased about it that I just went online and at Parts Select website it was easy to find what I needed, a fair price and the 4 bowls arrived within 2 days!
Other Parts Used:
Was this helpful?
Thank you for voting!
No problem installing the sensor
1 person
found this instruction helpful.
-
tommy from FAYETTEVILLE, NC
- Very Easy
- Less than 15 mins
-
Screw drivers
I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted
Was this helpful?
Thank you for voting!
Oven would not hold temperature, not turn on, and would shut off during use.
1 person
found this instruction helpful.
-
John from Arvada, CO
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Phili
... Read more
ps head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.
Read less
Was this helpful?
Thank you for voting!
"F3" error message and no oven heat
1 person
found this instruction helpful.
-
Pat from PAYSON, AZ
- Very Easy
- 15 - 30 mins
-
Screw drivers
Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and
... Read more
behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!
Read less
Was this helpful?
Thank you for voting!
2 Service Elements Didn't Work (Didn't heat up)
1 person
found this instruction helpful.
-
Roseann from MEADVILLE, PA
- Very Easy
- Less than 15 mins
Unplugged old elements and plugged in new ones
Other Parts Used:
Was this helpful?
Thank you for voting!
Element burn out. Would not heat
1 person
found this instruction helpful.
-
Dennis from AIKEN, SC
- Very Easy
- 15 - 30 mins
-
Nutdriver
Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall
... Read more
screws and turn Circuit breaker power back on. Done and Done
Read less
Was this helpful?
Thank you for voting!
The heating element on the left front burner was out
2 of 4 people
found this instruction helpful.
-
Julie from Salt Lake City, UT
- Really Easy
- Less than 15 mins
Pulled the old one out and plugged the new one in. It was that simple!
Was this helpful?
Thank you for voting!
oven not heating to set temp. 100 degrees too cold
2 of 4 people
found this instruction helpful.
-
Robert from Funston, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.
Was this helpful?
Thank you for voting!
surface element needed to be replaced along with all the drip Bowls
2 of 4 people
found this instruction helpful.
-
Tawnia from SHOW LOW, AZ
- Really Easy
- Less than 15 mins
take out the old put in the new
Other Parts Used:
Was this helpful?
Thank you for voting!