38HA Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Indicatror Light For 6" Burner Quit Working
5 of 7 people
found this instruction helpful.
-
NANCY from LITTLETON, CO
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Ok this is a glasstop jenn air cce3531b, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the
... Read more
counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since I had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. Thanks you partselect
Read less
Was this helpful?
Thank you for voting!
Replacement of broil element in wall oven
4 of 4 people
found this instruction helpful.
-
David from San Rafael, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
In principle it should be easy to replace the broil element in the wall oven, after unscrewing the supports for the back and front of the element (see other postings for details). The difficulty is with the ground screw, which is inconveniently only accessible from behind close to the back wall of the oven. A very short phillips screw d
... Read more
river is required, but designed so that good torque can be applied for unscrewing and replacing. The newly designed ground connector on the latest replacement elements makes life a little easier, but still be prepared to work slowly and carefully to complete the replacement. Note the new ground screws supplied only work with a flat-blade screw driver, not a phillips-type.
Read less
Was this helpful?
Thank you for voting!
One of the electric stove top elements had burnt out
4 of 5 people
found this instruction helpful.
-
Anthony from Palmyra, VA
- Really Easy
- 30 - 60 mins
-
Screw drivers
The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on th
... Read more
e new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.
Read less
Was this helpful?
Thank you for voting!
Oven was not correctly heating to set temperature
4 of 5 people
found this instruction helpful.
-
Trace from Ofallon, MO
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces
... Read more
of sheet metal back on and plugged in the oven.
Read less
Was this helpful?
Thank you for voting!
Panel light burnt out after 10 years
4 of 5 people
found this instruction helpful.
-
Pamela from La Junta, CO
- Really Easy
- Less than 15 mins
I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just
... Read more
4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .
Read less
Was this helpful?
Thank you for voting!
The drip bowls were all caked and corroded.
4 of 5 people
found this instruction helpful.
-
Terry from Mountain City, TN
- Really Easy
- Less than 15 mins
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
Other Parts Used:
Was this helpful?
Thank you for voting!
Old coil broke.
6 of 12 people
found this instruction helpful.
-
Paula Collins from Needham, MA
- Really Easy
- Less than 15 mins
After I removed the piece of metal separating the two wires, I inserted the unit with no problem.
Was this helpful?
Thank you for voting!
broken terminal
3 of 3 people
found this instruction helpful.
-
Gary from Shirley, IN
- Really Easy
- Less than 15 mins
Simply removed the old heating element and plug the new element terminals into socket.
Was this helpful?
Thank you for voting!
Burned up oven door gasket needed replaced.
7 of 15 people
found this instruction helpful.
-
Daniel from Prescott, MI
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt awa
... Read more
y about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Read less
Was this helpful?
Thank you for voting!
Oven erratic, not heating correctly, timer beeper sounding
3 of 3 people
found this instruction helpful.
-
Dave from SANTA BARBARA, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched
... Read more
off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
Read less
Was this helpful?
Thank you for voting!
ovens wouldn't maintain temperature after preheat cycle
3 of 4 people
found this instruction helpful.
-
sherri from elk horn, IA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.p
... Read more
lugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!
Read less
Was this helpful?
Thank you for voting!
piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.
3 of 4 people
found this instruction helpful.
-
George from Irving, TX
- Really Easy
- Less than 15 mins
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
Other Parts Used:
Was this helpful?
Thank you for voting!
i sat a tupperware bowl on a hot burner and it stuck to the burner so i had to replace it
3 of 4 people
found this instruction helpful.
-
judy from palatine, IL
- Really Easy
- 15 - 30 mins
just plugged it in!
Was this helpful?
Thank you for voting!
Replace the oven Sensor
3 of 5 people
found this instruction helpful.
-
Michael from Exeter, NH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not loo
... Read more
k for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike
Mike
Read less
Was this helpful?
Thank you for voting!
the burner element stopped working
2 of 2 people
found this instruction helpful.
-
Dominic from Fleetwood, PA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Unscrewed ceramic stove top , lifted top and exposed element , unscrewed element from top and disconnected wireing (marking wires to assure proper reinstillation .
Took new element and attached to top and returned wires to proper terminals , there was A slight change in wireing but was easy to understand and quick to adjust to new el ... Read more ement .
Replaced top on stove and rescrewed to secure .
Took new element and attached to top and returned wires to proper terminals , there was A slight change in wireing but was easy to understand and quick to adjust to new el ... Read more ement .
Replaced top on stove and rescrewed to secure .
Read less
Was this helpful?
Thank you for voting!