EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38HA Magic Chef Range - Instructions

All Instructions for the 38HA
91 - 105 of 257

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burnt out
2 of 4 people found this instruction helpful.
  • David from Elba, AL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Was this helpful?
Thank you for voting!
Replaced Burned-out Cooktop Element
1 person found this instruction helpful.
  • Seth from Old Orchard Beach, ME
  • Easy
  • 15 - 30 mins
  • Nutdriver
Exact fit, but read the instructions! Male connectors on element are labeled 1A 1B 2A 2C, very faintly etched in the ceramic. Even though the old and new elements look the same (and I took photos to aid installation), the connector locations are different -- 1A on the old element is where 2B on the new one is, etc. Used included exten sion wire for one that would not reach with the new configuration and everything works perfectly.
Was this helpful?
Thank you for voting!
Right rear burner under glass no longer would heat
1 person found this instruction helpful.
  • John from Maple Valley, WA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Turned off power to cooktop and double checked
Lifted up entire cooktop and rested it on two pieces of wood that spanned gap underneath
Removed screws from around edges to free the metal framework that holds the cooktop in place-- this requires spinning the cooktop a bit to get access to the back.
Lifted metal framework off
Lifted glass from cooktop off
Checked configuration of power plug ins against new part and noted where they should go. There was a slight difference of how plugs were arranged, but it was easy to logic out.
Removed old burner unit and plugged in new one. Ensure that nothing was touching contacts.
Replaced the glass top onto cooktop
Put metal frame back in place and screwed in
Lifted entire cooktop, removed boards, and lowered back into place
Was this helpful?
Thank you for voting!
Broiler element was only working on one side
1 person found this instruction helpful.
  • Helen from SPRINGFIELD, OH
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Grandson spent 1/2 hour installing unit and 15 minutes of that time was trying to get the very short grounded screw to begin to thread. It was a very small space to work in and it kept falling out. The instructions were a lot to be desired - almost nothing. He went to YouTube and got very explicit instructions. Then he had no problem as to what to do. The unit is working great now.
Was this helpful?
Thank you for voting!
Oven temperature fluctuates
1 person found this instruction helpful.
  • Larry from SOLON, IA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.
Was this helpful?
Thank you for voting!
Element in oven would not adjust to the oven temperature.
1 person found this instruction helpful.
  • Dolores from Edmond, OK
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fi sh out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.
Was this helpful?
Thank you for voting!
Half of broiler element worked
1 person found this instruction helpful.
  • Paul from SEATTLE, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Turned off power at panel. Removed 2 Phillips screws holding broiler element support in place. Squirted 2 additional Phillips head screws attaching element to back of stove with WD-40 and removed screws. Slid element out to access electrical connection and used short phillips screwdriver to remove. Reattached electrical connection to new element with short screwdriver (no fun as you are cantilevered into the oven and have to hold the element, the screw and the screwdriver to do this). Slid element into support and screwed support to top of stove cavity to align element. Installed screws holding element onto back wall. Turned on power and ran element long enough to dissipate WD-40 fumes.
Was this helpful?
Thank you for voting!
Small burner on glass top stove stopped working.
1 person found this instruction helpful.
  • REX from VIRGINIA BEACH, VA
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don 't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.
Was this helpful?
Thank you for voting!
Drip Pans were stained and burned on.
1 person found this instruction helpful.
  • Sandra Collignon from SANTA CLAUS, IN
  • Really Easy
  • 30 - 60 mins
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this helpful?
Thank you for voting!
F5 fault code kept appearing
1 person found this instruction helpful.
  • Louis Rodriguez from Granbury, TX
  • Very Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis
Was this helpful?
Thank you for voting!
Oven not heating to desired temp
2 of 5 people found this instruction helpful.
  • Raymond from Ridgecrest, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cab le adapter that came with the new sensor was needed in my case.
Was this helpful?
Thank you for voting!
Oven would not heat
1 of 2 people found this instruction helpful.
  • Ralph from Nicholasville, KY
  • Easy
  • 30 - 60 mins
  • Screw drivers
Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and ove n works like new.
Was this helpful?
Thank you for voting!
Drip bowls very dirty and stained
1 of 2 people found this instruction helpful.
  • john from donna, TX
  • Really Easy
  • Less than 15 mins
Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering proces ses were simple and delivery was faster than I hed expected.
Thank you
Was this helpful?
Thank you for voting!
Old burner pan warped.burner sat at 15 degree angle.
1 of 2 people found this instruction helpful.
  • Michael from Portland, OR
  • Really Easy
  • Less than 15 mins
Removed burner and then burner pan.Then replaced pan and reinstalled burner.
Was this helpful?
Thank you for voting!
Replaced appliance bulb in owen
1 of 2 people found this instruction helpful.
  • Billy from Grand Prairie, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed burnt bulb. On replacing the bulb I glued the bracket, retainer gasket and bulb cover together- I used only a small amount of glue-just enough to hold the three items together. You need to do this since the three items slip in your hand while you attempt to screw the bracket to the oven wall. Need my help, email me @ Lexidog999@t x.rr.com
Was this helpful?
Thank you for voting!
All Instructions for the 38HA
91 - 105 of 257