3889 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
freezer not working
7 of 13 people
found this instruction helpful.
-
robert from wall, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
replaced condenser fan motor.
also, i ordered the part on a tuesday and received it the next day. partselect is a very well run company.
also, i ordered the part on a tuesday and received it the next day. partselect is a very well run company.
Was this helpful?
Thank you for voting!
Oven would not maintain temperature
5 of 7 people
found this instruction helpful.
-
KATHY from PLEASANT GAP, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is l
... Read more
ike new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.
Read less
Was this helpful?
Thank you for voting!
Indicatror Light For 6" Burner Quit Working
5 of 7 people
found this instruction helpful.
-
NANCY from LITTLETON, CO
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Ok this is a glasstop jenn air cce3531b, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the
... Read more
counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since I had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. Thanks you partselect
Read less
Was this helpful?
Thank you for voting!
Left front burner went out.
5 of 7 people
found this instruction helpful.
-
Donald from North Highlands, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed 8 screws of retainer holding glass top to box.. Pulled 5 knobs and glass top and set aside. Popped 2 retaining clips holding burner , removed them and transferred to new burner (#12 and #48 position). Used wide blade screwdriver to facilitate removing terminals from old burner and attached terminals to new burner.Popped retaining
... Read more
clips into crossbeam, put glass top on and 8 screws back into retainer. Works great.
Read less
Was this helpful?
Thank you for voting!
The 6" heating element stop working on the stove top.
4 of 4 people
found this instruction helpful.
-
JULIUS from JACKSON, MI
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
First I reviewed a video on YouTube by this site. Even though the range on the video was not the same as mind, it gave me an idea on what to do. I proceeded to pull the rang out from the wall and disconnected the power plug. Next I removed two screws from the back located on the left and used a flat blade screw driver to depress two brack
... Read more
ets on the front to release the glass top panel. I unplugged the wiring harness and disconnected the grounding wire and took the glass panel off and laid it upside down on the kitchen table. I removed the old heating element first by unplugging the wiring and removing the brackets that held it in place. Installed the new one, plugged in all wirings, brackets, screws and replace the top back on the stove.
Read less
Was this helpful?
Thank you for voting!
The Icemaker failed to make ice
8 of 16 people
found this instruction helpful.
-
Dean from Folsom, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I pulled the refrigerator away from the wall and turned off the water to the refrigerator and unplugged it from the wall. After removing the icebucket from the freezer I located the mounting screws, loosened them, unplugged the electrical connection below the icemaker and carefully removed it from the freezer. I unpacked the replacement i
... Read more
cemaker, matched it against the original and attached the electrical connection adapter. Using the slots provided on the new icemaker I placed it over the mounting screws after aligning the water inlet pipe properly. I tightened the mounting screws while maintaining the icemaker in a level position. I plugged in the electrical connector. Then I replaced the icebucket, plugged in the refigerator back into the 110VAC outlet, turned on the water and repositioned the refrigerator in it's normal position.
Read less
Was this helpful?
Thank you for voting!
The lights were on inside however the the water/ice dispenser did not work and the fridge and freezer side was not cooling
5 of 7 people
found this instruction helpful.
-
Rickey from DUMAS, AR
- Really Easy
- 30 - 60 mins
-
Socket set
Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugge
... Read more
d it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.
Read less
Was this helpful?
Thank you for voting!
One of the electric stove top elements had burnt out
4 of 5 people
found this instruction helpful.
-
Anthony from Palmyra, VA
- Really Easy
- 30 - 60 mins
-
Screw drivers
The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on th
... Read more
e new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.
Read less
Was this helpful?
Thank you for voting!
no ice made
5 of 8 people
found this instruction helpful.
-
Robert from San Marcos, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Performed self test.turned off ice maker switch four 5 minutes.Then turn on switch,within 10 seconds,pushed ice paddle 3 times,with 1 second in between each push.Push all the way back and release. Ice maker should cycle and squirt water. My ice maker did neither.I unplugged cord from fridge.So i replaced the ice maker.After a couple of s
... Read more
crews had ice again !
Read less
Was this helpful?
Thank you for voting!
Broiler part wouldn't heat. Element internally broken
5 of 8 people
found this instruction helpful.
-
Richard from Perkinsville, VT
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
i removed the two screws that holds the element in. I pulled the element out and disconnected the wires and I had to adapt a double male adapter to the wire ends and plug the wires back onto the element. The old element had male spades and the new element had female spades.
Other Parts Used:
Was this helpful?
Thank you for voting!
No ice
4 of 5 people
found this instruction helpful.
-
Edward from Kissimmee, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
Ice maker not working. Received my order in 30 hours. (Excellent) After installing ice maker and water valve, I noticed that where the water enters through the freezer to the ice maker spout, there was a frozen spot in the connector. After melting the ice blockage with a hair dryer, the ice maker and water valve began working. No problem
... Read more
since. Unit working perfectly.
Read less
Was this helpful?
Thank you for voting!
Needed to replace the oven door gasket/seal
4 of 5 people
found this instruction helpful.
-
Daniel from Katy, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old
... Read more
gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.
Read less
Was this helpful?
Thank you for voting!
Fridge doesn't cool properly; freezer iced up
4 of 5 people
found this instruction helpful.
-
Will from Houston, TX
- Easy
- 15 - 30 mins
-
Nutdriver
You will need a 1/4" nut driver or socket & extension.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.
Was this helpful?
Thank you for voting!
oven would not come to set heat
4 of 5 people
found this instruction helpful.
-
Ralph from Portsmouth, NH
- Really Easy
- Less than 15 mins
-
Screw drivers
slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.
Was this helpful?
Thank you for voting!
Door gasket was hard and brittle from baked-on grease - heat leaking around door
4 of 5 people
found this instruction helpful.
-
Harlen from Spring Creek, NV
- Really Easy
- Less than 15 mins
Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in
... Read more
each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.
Read less
Was this helpful?
Thank you for voting!