EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3889 - Instructions

All Instructions for the 3889
61 - 75 of 401

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not preheat and gave 'F1' error
9 of 11 people found this instruction helpful.
  • Joshua from Reno, NV
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...
Was this helpful?
Thank you for voting!
F-3 error code
8 of 8 people found this instruction helpful.
  • Mark from Lake Orion, MI
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.
Was this helpful?
Thank you for voting!
inner glass busted
9 of 11 people found this instruction helpful.
  • robert from orange, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed door by opening it to first stop and lifted it up off the hinge's. I removed all screws that held the inner panel to the outer panel and handle. Removed inner panel from outer panel, then glass and insulation, replaced glass and insulation and panel.

Replaced screws and handle,pulled hinge's out to first stop and sli d door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.

PS: shipping was fast and price was great.
Thanks Bob G.
Was this helpful?
Thank you for voting!
Unit wouldn't maintain a low temp.
9 of 12 people found this instruction helpful.
  • David from Erie, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench set
Opened back,found fan not moving. Cleaned out dust and dirt. Received exact fan motor. Easiest fix I ever performed(very unusual). Fridge now runs great! Also, water line to in-door ice and water dry roughted and sprung leak. Replaced tubing.
Was this helpful?
Thank you for voting!
Original oven light lens had cracked and broken in two.
17 of 36 people found this instruction helpful.
  • Pat from Bucklin, KS
  • Really Easy
  • Less than 15 mins
I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).
Was this helpful?
Thank you for voting!
Front left burner quit after bright flash under glass top
11 of 19 people found this instruction helpful.
  • Brian L. from Wilkes-Barre, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I ohmed out the burner element that wasnt working and found it was open. I ordered a new element thru PartSelect and installed it in the stove. I powered up the stove and turned on the burner but it didnt get hot. After a bit of testing I found that the new elements safety overtemp terminals werent in the same configuration as the origina l unit. I made some wiring adjustments and the burner was operating properly. Thanks PartSelect
Was this helpful?
Thank you for voting!
Broken gear
8 of 10 people found this instruction helpful.
  • D.H. from Mulberry, AL
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed old gear and tapped the replacement on.
Was this helpful?
Thank you for voting!
Freezer not getting cold enough to freeze ice cream
8 of 10 people found this instruction helpful.
  • Gary from ROSETO, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
Was this helpful?
Thank you for voting!
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
7 of 7 people found this instruction helpful.
  • Jared from UNION GROVE, AL
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Was this helpful?
Thank you for voting!
Inner Galls on door was craked
8 of 11 people found this instruction helpful.
  • Randall from Katy, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Remove outer panel first, outer glass and handle come off as one piece. Be carefull to secure as last screws are removed. Remove inner silver panel. Remove broken glass and replace with new. Reaassemble. Around 10 Phillips head screws altogether. Much easier than I thought
Was this helpful?
Thank you for voting!
oven temperature not reaching setting/temp. up and down
7 of 8 people found this instruction helpful.
  • Ellen from Schenectady, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed back of stove, removed screws from sensor inside oven, unplugged connector from back of stove, pulled sensor out through oven; installed new sensor, replaced back of stove. Set the oven to bake, waited for it to pre-heat; the oven thermometer showed that the same problem was occurring, the sensor replacement didn't work.
Was this helpful?
Thank you for voting!
Oven temperature lower then setpoint.
7 of 8 people found this instruction helpful.
  • Robert from Massapequa, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
After shutting the main valve behind stove. Removed all shelves and rear cover from stove. Unplugged the plug to the sensor. Removed the two mounting screws and pulled the old sensor out. Installed new sensor and plugged it in again. After reinstalling the rear cover and shelves, replugged in power, openned the gas valve behind the stove and tested with soapy water to make sure there wasn't ant developed leaks. Turned on oven with a test thermometer in it. Monitored operation and now oven temperature is roughly 10 to 20 degrees to the setpoint.
Was this helpful?
Thank you for voting!
My ice maker quit making ice.
8 of 12 people found this instruction helpful.
  • Steve from Louisville, KY
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the maker from the freezer, three phillps head screws, I pulled off the white plastic cover and found the top (small) gear had poped out, after carefull inspection, I notice two missing teeth. I ordered a new gear from ParstSelect re-installed and with in two days my ice maker was working like new. I estimate I saved myself seve al hundred dollars, my wife wanted to call a service professional or worse buy a new refrigerator freezer. Thanks PartSelect!
Was this helpful?
Thank you for voting!
Ice maker would not shut off
8 of 12 people found this instruction helpful.
  • Jack from Bloomington, IL
  • Easy
  • 15 - 30 mins
Removed the ice maker from the freezer. Removed the switch. Tested the switch with a multimeter. Ordered a new switch. Replaced it in the box. Installed the ice maker ( 3screws and electric cord plug. It works. Details available on the internet.
Was this helpful?
Thank you for voting!
The F3 error code displayed and beeped during use of the oven and oven shut down.
7 of 9 people found this instruction helpful.
  • Debra from Colts Neck, NJ
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
My husband and I began to pull the oven out and I realized that it was too heavy for me to hold. Luckily we were able to get another man to help. Other than that it was easy. Also, it took us awhile to figure out which screws secured the oven into the cabinet. We saved over $1000.00 on a new oven and installation. Kudos to everyone who added their comments! They gave us courage to give it a try.
Was this helpful?
Thank you for voting!
All Instructions for the 3889
61 - 75 of 401