3889 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Baked on sauce
12 of 16 people
found this instruction helpful.
-
Julie from Newnan, GA
- A Bit Difficult
- More than 2 hours
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.
Was this helpful?
Thank you for voting!
Refridgerator Freezer stoped making ice
17 of 31 people
found this instruction helpful.
-
Marion from Palm Coast, FL
- Easy
- 30 - 60 mins
-
Screw drivers
Turned off power, removed cover from Ice maker, checked resistance across thermostat for zero (read open), all other switches read proper value (when activated). Ordered and received thermostat. Removed Ice Maker from freezer, removed two screws holding ice tray to Control Assembly. Removed Thermostat and replaced with new one. Applied Si
... Read more
licone Sealant to face of Thermostat for adhesion to ice tray when assembled. Remounted Ice Tray to Control Assembly and remounted in freezer. Works Great...
Read less
Was this helpful?
Thank you for voting!
ice maker quit working
14 of 23 people
found this instruction helpful.
-
Timothy from Ayden, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers
I was looking to see if there was a reason that there was no ice. By luck I removed the cover to the ice maker and found two gears, one of which was damaged. I could see one of the gears had missing teeth. I ordered part to fix problem and received the gear. 10 minutes later, viola! ice maker restarted and ice was falling in a few minute
... Read more
s.
Read less
Was this helpful?
Thank you for voting!
spin cycle was not working / poor
11 of 14 people
found this instruction helpful.
-
Craig from Plano, TX
- Easy
- 30 - 60 mins
-
Pliers, Socket set
Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive ass
... Read more
embly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.
Read less
Was this helpful?
Thank you for voting!
Ice machine wasnt making ice
14 of 23 people
found this instruction helpful.
-
Robert from Auburn, AL
- Really Easy
- Less than 15 mins
-
Screw drivers
First I turned the refrigerator and water line off. Then moved to the freezer section, followed the directions, removed the two screws. Directions state to not remove them but I had to in this case. Unplugged the ice maker and removed it from the freezer. I installed the two mounting screws then tried to plug the electrical connection bac
... Read more
k in but had to use the adaptor cord furnished in the kit. The cord was a little long but I tucked it in and mounted the ice maker. Turned it on then turned the refrigerator and water back on and in a few hours had ice! Very easy to do!
Read less
Was this helpful?
Thank you for voting!
Fridge keeps cycling on and off and a clicking sound happens every time compressor cycles.
10 of 11 people
found this instruction helpful.
-
Kirk E from GRASS VALLEY, CA
- Easy
- Less than 15 mins
-
Screw drivers
I opened the back panel of the fridge and exposed the compressor. Unplugged existing run capacitor and installed new one with the addition of the sleeve that is stated must be installed around the run capacitor.
Everything I read and on this web site says that based on these symptoms, that the problem is the run capacitor. I search ... Read more ed and search for a part called a start relay which plugs in to the compressor. This run capacitor plugs in to this other part which I take as the start relay.
Installing this run capacitor did not solve the problem. The fridge compressor keeps cycling on and off. Freezer doesn't keep as cold as it should.
Everything I read and on this web site says that based on these symptoms, that the problem is the run capacitor. I search ... Read more ed and search for a part called a start relay which plugs in to the compressor. This run capacitor plugs in to this other part which I take as the start relay.
Installing this run capacitor did not solve the problem. The fridge compressor keeps cycling on and off. Freezer doesn't keep as cold as it should.
Read less
Was this helpful?
Thank you for voting!
Ice maker Stripper lost a tooth
10 of 12 people
found this instruction helpful.
-
Ernest W. from Charlotte, NC
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First turn off the power, remove the ice tray, remove the two screws holding the ice maker to the side of the freezer, use the screw driver to gently open the electrical clip for the power cord inside the freezer, remove the complete unit from freezer, bend the old stripper from the holding pin- it is flexible- it will bend, replace the n
... Read more
ew stripper on the holding pin and bend into the slot to hold it firmly, no water will come out from the fill cup into the freezer, plug in the power cord, mount back to side of freezer, you are done.
Read less
Was this helpful?
Thank you for voting!
broken ice maker
10 of 12 people
found this instruction helpful.
-
robert from bensalem, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
removed 3 screws unplug and remove old unit. install two screws install new ice maker, tighten screws plug in and turn on. had ice in 20 min.
Was this helpful?
Thank you for voting!
Burner not working
12 of 18 people
found this instruction helpful.
-
Warren C from Slidell, LA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
First thing- I cut off power to the range. I then removed two screws to allow the cook top to be lifted. I marked the wiring and replaced the burner. Reapplied power and started cooking!
Was this helpful?
Thank you for voting!
thermistat and defrost timer
10 of 13 people
found this instruction helpful.
-
brad from brenham, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
i have a friend that had a big side by side refrigerator . he had repair man after repairman come and look at it. one thought it was the overload relay in the back and another just said it was compressor problems. this went on for over a month. after all of this and no one able to fix it he went and got another refrigerator . being the ti
... Read more
nker with stuff kind of person i am i said i will come and get the old one to keep him from having to haul it off (he agreed). well i did my home work and tried a few things messing with it. tapping on the thermistat resetting the defrost timer and it dawned on me that that the fridge would run great if i wiggle a wire on the thermistat and reset the defrost timer. so i get on the internet look around for the parts. come to find out they were realy cheap. the day they get here i break out with a screw driver and a nut driver and take the cover off. i take the old parts out and put the new ones in in about 15 minutes. i wiped the inside of the frige clean and pluged it back in. well in no time flat this thing was cooling like a northern blowing through in january. then it dawned on me that i have a 27 cubic ft frige that i didnt pay any thing for (well the 65 bucks i spent on the parts) and it runs great. what a deal.
after getting the big side by side fixed up and running like a champ i realized i have a refrigerator in the garage that my parents gave me a couple of years ago that only ran for a couple of months. well i get brave and decide to try my luck with the second one. due to it sitting up for so long and the humidity i had to do a little more work to it. i replaced a few wires, changed out a couple of connections, put a thermistat , a defrost timer and a evapmotor in it this thing also ran like a champ. i cleaned it up real good ran some steel wool over the outside and sprayed a couple of coats of enamel on it and it looks brand new.
so to end this story i spent about 140 bucks and i have two refrigerators a big side by side ice and water despensing refrigerator in the house and a 17 cubic ft refrigerator in the garage (the wife was happy simply because i had a place to put beer and bait).
if i would have went and purchased both of these refrigerators i would have spent about $1400 for the side by side and about $450 for the other one. man what a bargin, so from now on even if it seems a little dificult i dont get rid of any thing until i give it a good look over and see if i can fix it. i saved a total of $1700 (minus tax).
after getting the big side by side fixed up and running like a champ i realized i have a refrigerator in the garage that my parents gave me a couple of years ago that only ran for a couple of months. well i get brave and decide to try my luck with the second one. due to it sitting up for so long and the humidity i had to do a little more work to it. i replaced a few wires, changed out a couple of connections, put a thermistat , a defrost timer and a evapmotor in it this thing also ran like a champ. i cleaned it up real good ran some steel wool over the outside and sprayed a couple of coats of enamel on it and it looks brand new.
so to end this story i spent about 140 bucks and i have two refrigerators a big side by side ice and water despensing refrigerator in the house and a 17 cubic ft refrigerator in the garage (the wife was happy simply because i had a place to put beer and bait).
if i would have went and purchased both of these refrigerators i would have spent about $1400 for the side by side and about $450 for the other one. man what a bargin, so from now on even if it seems a little dificult i dont get rid of any thing until i give it a good look over and see if i can fix it. i saved a total of $1700 (minus tax).
Read less
Was this helpful?
Thank you for voting!
Ice maker was not making ice
10 of 13 people
found this instruction helpful.
-
Larry from Virginia Beach, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplugged the old ice maker. Removed the two screws that held it in. Removed the old ice maker and replaced it with the new one. Put back the two screws, plugged it back in and turned on the power switch. It started making and dropping ice in the first 1/2 hour.
Was this helpful?
Thank you for voting!
Bought with no icemaker
11 of 16 people
found this instruction helpful.
-
Dale from El Dorado, AR
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench set
By following the instructions in the manual that went with it, I used the parts in the order that the instructions said. The illustrations were very easy and now we dont have to use ice cube trays any longer. Any person without experience that can follow directions can put in an icemaker with the simple to follow instructions that was use
... Read more
d in the manual.
Read less
Was this helpful?
Thank you for voting!
Factory ice maker was running water out of the fridge onto the floor.
9 of 10 people
found this instruction helpful.
-
Don from Cambridge, WI
- Really Easy
- More than 2 hours
-
Screw drivers
My wife and I decided to tackle this job on a Saturday. The fridge was due for a good cleaning anyway. We pulled it out and shut off the water to the ice maker.
I took out the old ice maker, (two screws and the plug) Then went to the back of the fridge. removed the cardboard cover at the bottom of the frigdge and took the mountin ... Read more g screw out of the water valve. I had a double valve for the no longer working in-door water so I made sure to identify Then installed the new water valve. Note: be sure to check your connections for leaks before mounting the water valve - it is easier to see and fix them !!!! You can leave the water on at this point because the icemaker and water valve will not operate until the icemaker is plugged in. Next choose the right water fill cup, and install the ice maker to the existing screw mounts and plug in the connector. Note: be sure the ice maker is turned off. Start the fridge, let it get cold, then turn on the icemaker.
Overall this is a great multi install package - Don't worry about extra parts because you will have some. If we would have just needed to do the icemaker and not clean the fridge, I could have done it in about an hour.
Overall I would highly recommend this package vs what is available at other retailers for more money. Best Buy has a bargain replacement icemaker but does not have the versatility and completeness of this product. I give this product 5 stars.... dm
I took out the old ice maker, (two screws and the plug) Then went to the back of the fridge. removed the cardboard cover at the bottom of the frigdge and took the mountin ... Read more g screw out of the water valve. I had a double valve for the no longer working in-door water so I made sure to identify Then installed the new water valve. Note: be sure to check your connections for leaks before mounting the water valve - it is easier to see and fix them !!!! You can leave the water on at this point because the icemaker and water valve will not operate until the icemaker is plugged in. Next choose the right water fill cup, and install the ice maker to the existing screw mounts and plug in the connector. Note: be sure the ice maker is turned off. Start the fridge, let it get cold, then turn on the icemaker.
Overall this is a great multi install package - Don't worry about extra parts because you will have some. If we would have just needed to do the icemaker and not clean the fridge, I could have done it in about an hour.
Overall I would highly recommend this package vs what is available at other retailers for more money. Best Buy has a bargain replacement icemaker but does not have the versatility and completeness of this product. I give this product 5 stars.... dm
Read less
Was this helpful?
Thank you for voting!
When the oven was turned on, F2 and F4 came on. Oven wouldn't heat.
9 of 11 people
found this instruction helpful.
-
Crystal from Scott City, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now ju
... Read more
st like a new oven.
Read less
Was this helpful?
Thank you for voting!
Will not make ice
13 of 23 people
found this instruction helpful.
-
GEORGE from ELIOT, ME
- Easy
- Less than 15 mins
-
Screw drivers
Bing , Bang, Boom.
Was this helpful?
Thank you for voting!