3889 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No power to the fan and compressor
222 of 302 people
found this instruction helpful.
-
Christian from Kearneysville, WV
- Really Easy
- Less than 15 mins
-
Screw drivers
I have a fridge in my garage. I have found that a glass of ice water or a cold drink outside is very important to me. When I discovered melting ice dripping onto the garage floor I was very upset. I spun the fridge and found that the compressor and fan weren't starting. I got out my multi-meter and discovered that power was not makin
... Read more
g it to these components. I did some research and found the wiring diagram online. There really isn't too much going on with a fridge and the most likely candidate seemed to be the run capacitor. I ordered the part, replaced it in a few minutes and the fridge began working again.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
F1 code - gas over would not heat.
172 of 188 people
found this instruction helpful.
-
george from birmingham, AL
- Easy
- 15 - 30 mins
-
Screw drivers
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.
Replacing ... Read more the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.
Replacing ... Read more the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.
Read less
Was this helpful?
Thank you for voting!
ice stalactites were drooling out of the icemaker and gumming up the cubes in the receiving tray.
91 of 133 people
found this instruction helpful.
-
Gerald from Benicia, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I first shut off water flow to the fridge. Examination of the package (which was not exact in appearance to the original) demonstrated that the electrical connectors were well-insulated so I arrogantly and successfully proceded without disconnecting the power. My fridge is old enough that the model doesn't appear exactly on anyone's list
... Read more
so I wasn't alarmed that it took an extra 10 minutes or so to noodle out how to adapt the slightly different inlet cowling and electrical cord with extension, but the device is pretty simple.
Soon I loosened the two mounting screws with a nut driver, used a screwdriver to pry away the plastic snap-in housing over the electrical socket on the fridge inner wall and pulled away the electrical plug. The original water fill tube remained in its cavity, ready for re-use.
The new unit's mounting points matched the original screw locations perfectly, as did the fill cowling - which on the replacement icemaker has two possible attachment points. The new unit's electrical connector required an extension pigtail to adapt to my socket, but it was included in the package. The extra cable posed a minor cosmetic issue because it hangs in the collection basket a bit, but that will soon be remedied with a tie wrap.
After the water was restored and an anxious wait of a few hours, we had well-formed ice cubes that weren't all stuck together and the stalactites haven't reappeared.
Soon I loosened the two mounting screws with a nut driver, used a screwdriver to pry away the plastic snap-in housing over the electrical socket on the fridge inner wall and pulled away the electrical plug. The original water fill tube remained in its cavity, ready for re-use.
The new unit's mounting points matched the original screw locations perfectly, as did the fill cowling - which on the replacement icemaker has two possible attachment points. The new unit's electrical connector required an extension pigtail to adapt to my socket, but it was included in the package. The extra cable posed a minor cosmetic issue because it hangs in the collection basket a bit, but that will soon be remedied with a tie wrap.
After the water was restored and an anxious wait of a few hours, we had well-formed ice cubes that weren't all stuck together and the stalactites haven't reappeared.
Read less
Was this helpful?
Thank you for voting!
Ice maker stopped working
84 of 118 people
found this instruction helpful.
-
Dan from West Bloomfield, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
I unplugged the electrical connection. Then I removed the 2 screws holding the icemaker in place. I lifted out the old icemaker unit and put the new one in place. Then put the 2 screws back in and plugged in the new unit.
The icemaker started making ice very soon after turning the unit on.
The icemaker started making ice very soon after turning the unit on.
Was this helpful?
Thank you for voting!
broken ice maker part
78 of 108 people
found this instruction helpful.
-
Laura Beth from Mandeville, LA
- Really Easy
- Less than 15 mins
-
Screw drivers
used a screwdriver to remove screw and unplugged part. Plugged in new one and secured with a screw.
Simple
Simple
Was this helpful?
Thank you for voting!
Needed to replace oven door gasket.
58 of 69 people
found this instruction helpful.
-
Lori from Scottsdale, AZ
- Really Easy
- Less than 15 mins
-
Pliers
First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum.
Was this helpful?
Thank you for voting!
bad light socket
45 of 56 people
found this instruction helpful.
-
nancy from silsbee, TX
- Really Easy
- Less than 15 mins
unplugged refrigerator. removed light bulb from old socket. unsnapped old light socket and pulled it out just enough to diconnect the electrical plug that plugs into the socket . discarded the old socket and plugged in new socket. snapped in new socket into refrigerator. i watched how to do this simple procedure on you tube and decided to
... Read more
do it myself. easy easy easy
Read less
Was this helpful?
Thank you for voting!
Burned terminal block and filter board
95 of 208 people
found this instruction helpful.
-
Joseph from Decatur, GA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench set
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Was this helpful?
Thank you for voting!
Spin cycle stopped working
41 of 48 people
found this instruction helpful.
-
Brent from Highlands Ranch, CO
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Farly easy repair, once I figured out the problem. The clutch assebly plastic part broke (over 15 yrs old), which is the part that engages the drum for the spin cycle. Following the very helpful diagram on Part Select, I removed the agitator cap and bolt from inside the agitator assembly, and pulled the assembly out of the drum. Then I
... Read more
put the washer on its side and removed the three bolts and two hose claps that hold the motor assembly. I pulled the motor assembly along with the drive shaft out to access the clutch/brake assembly area, removed the broken plastic drive piece and re-assembled.
Read less
Was this helpful?
Thank you for voting!
Relay
42 of 54 people
found this instruction helpful.
-
John H from Austin, TX
- Really Easy
- 15 - 30 mins
Removed back panel. Opened cover to relay attached to the compressor and pulled off replacing with new relay. No problem.
Better than paying $250 for someone else to do it.
Better than paying $250 for someone else to do it.
Was this helpful?
Thank you for voting!
Ice maker quit making ice
40 of 53 people
found this instruction helpful.
-
Jeffrey from Bluefield, WV
- Really Easy
- 30 - 60 mins
-
Nutdriver
the first thing i did was replace the water valve at the bottom of the refrigerator but that didn't work so then i spent more time researching the problem on your site and your diagnostic said to replace the ice maker so i ordered it, took the old one out, plugged the new one in and we had ice the next day.
Was this helpful?
Thank you for voting!
Quit making ice.
37 of 49 people
found this instruction helpful.
-
Joe from Brentwood, TN
- Really Easy
- 15 - 30 mins
-
Screw drivers
There were not two screws as the instructions said. There was only one screw and I had to firmly pull it out after taking out the one screw. Then, to put the new one in, I had to line up two slots on two knob-like things and push it in firmly. Then screw the one screw in.
Other than the two-screw problem, it was easy.
Other than the two-screw problem, it was easy.
Was this helpful?
Thank you for voting!
ice maker leaked water slowly and froze the cubes together
41 of 62 people
found this instruction helpful.
-
Steven from Cave Creek, AZ
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
The replacement ice maker that GE supplies for my old refrigerator is a little different than the original. The electrical plug changed from a round plug to a square one. They include an adapter for it, but DON'T USE IT. There's not enough room for the bulky cord and connector. I got a much cleaner installation by taking apart the old and
... Read more
the new ice maker, and then splicing in the old connector into the new ice maker. You need to carefully unscrew a circuit board inside to wire it in, and it'll be more secure if you solider 3 wires instead of using crimp connectors. The instructions also tell you to use your old 'ice breaker', but it won't fit on the new ice maker. I just left the new ice maker's ice breaker on, and it seems to work perfect.
Read less
Was this helpful?
Thank you for voting!
Found cracked brake shoe
33 of 41 people
found this instruction helpful.
-
Michael from Trafalgar, IN
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, the
... Read more
n used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.
Read less
Was this helpful?
Thank you for voting!
replaced heating element on flat surface stove top
35 of 48 people
found this instruction helpful.
-
dennis from assonet, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed 4 screws and then lifted up the top it gave me access to the element I followed the direction that came with the element (very clear to follow) removed and installed the new element and it worked fine. Remember to unplug the stove if it is electric this is not in the instructions.
Was this helpful?
Thank you for voting!