3889 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
icemaker stripper fall a part
3 of 4 people
found this instruction helpful.
-
Ted from Harrisonburg, VA
- Easy
- 15 - 30 mins
-
Screw drivers
instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull"
Dremel and it works!The instalation part of the "job" was less then 10 min.
Dremel and it works!The instalation part of the "job" was less then 10 min.
Was this helpful?
Thank you for voting!
Ice maker didn't work.
3 of 4 people
found this instruction helpful.
-
Amanda from New Albany, MS
- Easy
- 15 - 30 mins
-
Screw drivers
Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable s
... Read more
hould be more flexible and adapt to the fridge a little more friendly.
Read less
Was this helpful?
Thank you for voting!
The inside glass was broken on oven door.
3 of 4 people
found this instruction helpful.
-
Jacob from Cotton, MN
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I was pleased with how the job went.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how ... Read more simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how ... Read more simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.
Read less
Was this helpful?
Thank you for voting!
Broiler front drawer slides broke
3 of 4 people
found this instruction helpful.
-
Ernie from Fremont, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I noticed the drawer on the broiler was sliding crooked and found the plastic slides had broken. Of course I thought it would be a hassle and not worth the time to fix it. I would just "live with it". Boy was I wrong, it was probably the simplest fix ever. It was easy to get the correct parts from PartSelect with their exploded and concis
... Read more
e diagram. The parts were ordered and delivered in a couple of days. It took me all of 10 minutes with a screwdriver to make the repairs. Now it is a good as new.
Read less
Was this helpful?
Thank you for voting!
Oven heat loss, door gasket needed replacement
3 of 4 people
found this instruction helpful.
-
Stephen from Chapell Hill, NC
- Really Easy
- Less than 15 mins
The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in plac
... Read more
e! Simple!
Read less
Was this helpful?
Thank you for voting!
Broiler drawer didn't track poperly
3 of 4 people
found this instruction helpful.
-
Keith from Atlanta, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove screw securing the broken drawer guide. Placed new drawer support in place and tightened screw. Replaced drawer. All done in less than 5 minutes (and cheaply).
Was this helpful?
Thank you for voting!
drain freezing up found cond fan not working
3 of 4 people
found this instruction helpful.
-
glenn from la harpe, KS
- Really Easy
- Less than 15 mins
Cleaned oh t freezer removed floor. Removed back inside wall removed and replaced fan and put back removed parts
L
L
Was this helpful?
Thank you for voting!
end cap to bar of freezer door broke
3 of 4 people
found this instruction helpful.
-
Kimberly A from Columbus, OH
- Really Easy
- Less than 15 mins
Snapped end cap onto bar and installed bar onto freezer door.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
Was this helpful?
Thank you for voting!
Not cooling and freezer freezing up
6 of 14 people
found this instruction helpful.
-
kenneth from carmel, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the condenser cover removed old fan blade defrosted the condenser section installed new blade and reassembled
Was this helpful?
Thank you for voting!
broken shelf end caps- right side of 2 shelves.
2 of 2 people
found this instruction helpful.
-
William from PRESQUE ISLE, ME
- Really Easy
- Less than 15 mins
After watching video I took off end shelf caps. It took close to 10 mins to replace them.
Was this helpful?
Thank you for voting!
Cap on the door retainer bar broke.
2 of 2 people
found this instruction helpful.
-
Mary from New Milford, NJ
- Really Easy
- Less than 15 mins
The replacement cap fit perfectly. Unfortunately when the orinigal cap broke it tookout a small piece of the surrounding plastic leaving nothing for the new cap to catch. I have the piece and tried several kinds of glue but nothing holds it securely enough. I would however readily recommend your company. The service was terrific.
... Read more Thank you.
... Read more Thank you.
Read less
Was this helpful?
Thank you for voting!
light wouldn't come out of socket
3 of 5 people
found this instruction helpful.
-
Joyce from Tacoma, WA
- Really Easy
- Less than 15 mins
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this helpful?
Thank you for voting!
Broken shelf retainer bar end cap.
2 of 2 people
found this instruction helpful.
-
Ruchik from Bronx, NY
- Really Easy
- Less than 15 mins
I ordered 2 end caps just to keep one as spare. Turned out I had ordered a size larger than the one already on the refrigerator. So I replaced both ends and it worked fine - with increased shelf space. Now I can even fit a gallon container with ease!!! Took about 20 seconds. I just wish there was an easier way to measure parts before orde
... Read more
ring. Otherwise, the entire process from order to finish took about 3 days.
Read less
Was this helpful?
Thank you for voting!
I didn't know if I could get a replacement part, but I googled "replacement parts" (or some such), and since this website looked easy to navigate, chose it. (Actually, I did my ordering via telephone). The sales rep. helped me clarify which part I needed, I ordered it, and received the part the very
2 of 2 people
found this instruction helpful.
-
Kaye from San Francisco, CA
- Really Easy
- Less than 15 mins
I simply snapped the two end pieces into place, attaching the guard rail. It was like putting the pieces of a very easy puzzle together‚ especially for someone like myself who is mechanically challenged.
Was this helpful?
Thank you for voting!
Old end cap broke.
2 of 2 people
found this instruction helpful.
-
Travis from North Quincy, MA
- Really Easy
- Less than 15 mins
Put the new end cap on and snapped it into place, took about 5 seconds.
Was this helpful?
Thank you for voting!