3868 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
door seal contaminated by a boil-over, not flexible
3 of 3 people
found this instruction helpful.
-
Rob from Yakima, WA
- Really Easy
- Less than 15 mins
From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.
Was this helpful?
Thank you for voting!
Gasket was worn out.
3 of 3 people
found this instruction helpful.
-
Michael from VALLEJO, CA
- Really Easy
- Less than 15 mins
-
Pliers
Put a new one in.
Was this helpful?
Thank you for voting!
Broiler drawer front slide plastic guides broke so drawer sagged and was difficult to pull out.
3 of 3 people
found this instruction helpful.
-
DOUGLAS from MESA, AZ
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the single phillips screw that held each plastic slide guide to the stove, and replaced the part reusing the screws. Was so simple I didn't even have to swear. This was my mother-in-law's stove, and she was so happy to have it repaired she's fed me twice since.
Was this helpful?
Thank you for voting!
Crazy codes and not heating the oven properly at desired temp settings
3 of 3 people
found this instruction helpful.
-
Stan from CHICAGO RIDGE, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. I
... Read more
f you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!
Read less
Was this helpful?
Thank you for voting!
Old element caught fire, replaced with new one
3 of 3 people
found this instruction helpful.
-
louis from CAHOKIA, IL
- Very Easy
- Less than 15 mins
-
Screw drivers
Removed screws of old element pulled clips off replaced with new element very easy
Was this helpful?
Thank you for voting!
drain freezing up found cond fan not working
3 of 4 people
found this instruction helpful.
-
glenn from la harpe, KS
- Really Easy
- Less than 15 mins
Cleaned oh t freezer removed floor. Removed back inside wall removed and replaced fan and put back removed parts
L
L
Was this helpful?
Thank you for voting!
Oven heat loss, door gasket needed replacement
3 of 4 people
found this instruction helpful.
-
Stephen from Chapell Hill, NC
- Really Easy
- Less than 15 mins
The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in plac
... Read more
e! Simple!
Read less
Was this helpful?
Thank you for voting!
Broiler front drawer slides broke
3 of 4 people
found this instruction helpful.
-
Ernie from Fremont, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I noticed the drawer on the broiler was sliding crooked and found the plastic slides had broken. Of course I thought it would be a hassle and not worth the time to fix it. I would just "live with it". Boy was I wrong, it was probably the simplest fix ever. It was easy to get the correct parts from PartSelect with their exploded and concis
... Read more
e diagram. The parts were ordered and delivered in a couple of days. It took me all of 10 minutes with a screwdriver to make the repairs. Now it is a good as new.
Read less
Was this helpful?
Thank you for voting!
Broiler drawer didn't track poperly
3 of 4 people
found this instruction helpful.
-
Keith from Atlanta, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove screw securing the broken drawer guide. Placed new drawer support in place and tightened screw. Replaced drawer. All done in less than 5 minutes (and cheaply).
Was this helpful?
Thank you for voting!
end cap to bar of freezer door broke
3 of 4 people
found this instruction helpful.
-
Kimberly A from Columbus, OH
- Really Easy
- Less than 15 mins
Snapped end cap onto bar and installed bar onto freezer door.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
Was this helpful?
Thank you for voting!
ovens wouldn't maintain temperature after preheat cycle
3 of 4 people
found this instruction helpful.
-
sherri from elk horn, IA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.p
... Read more
lugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!
Read less
Was this helpful?
Thank you for voting!
The inside glass was broken on oven door.
3 of 4 people
found this instruction helpful.
-
Jacob from Cotton, MN
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I was pleased with how the job went.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how ... Read more simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how ... Read more simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.
Read less
Was this helpful?
Thank you for voting!
was not defrosting
3 of 4 people
found this instruction helpful.
-
denis from freedom, NH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
first i removed all the screws inside the freezer compartment took out theback and bottom to get to the evap motor,unpluged the wires and removed the evap motor ,removed the fan from old unit and put it on the new unit them mounted it to the back wall of the fridge,,, and put back top and bottom
Was this helpful?
Thank you for voting!
one electric burner does not get hot
5 of 10 people
found this instruction helpful.
-
dinh from austin, TX
- Easy
- 15 - 30 mins
-
Screw drivers
swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. U
... Read more
sed the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.
Read less
Was this helpful?
Thank you for voting!
Temp out of wack
3 of 4 people
found this instruction helpful.
-
Peter from Montello, WI
- Really Easy
- More than 2 hours
-
Nutdriver
replaced heat sensor
Was this helpful?
Thank you for voting!