EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3868 - Instructions

All Instructions for the 3868
121 - 135 of 547

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Maytag range had "F3" code display, oven would not work.
2 of 2 people found this instruction helpful.
  • phillip from Farmington, NM
  • Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.
Was this helpful?
Thank you for voting!
Bake element eroded
2 of 2 people found this instruction helpful.
  • Alison from NORTH EASTON, MA
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
Everything was straightforward other than the tabs that the screws go through before going into the back of the oven were the wrong size and the predrilled holes were not in the right location. Had to trim the metal tabs and redrill the screw holes.
Was this helpful?
Thank you for voting!
Burner control knob/switch shaft had broken off.
4 of 8 people found this instruction helpful.
  • Steve from San Luis Obispo, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.
Was this helpful?
Thank you for voting!
The Refridgerator and Freezer were not cooling.
2 of 2 people found this instruction helpful.
  • Frank from VERO BEACH, FL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Installing the part repaired the fridge and freezer immediately.
Was this helpful?
Thank you for voting!
After cleaning, F1-1 error flashed and neither oven worked
3 of 5 people found this instruction helpful.
  • Georgene from Rock City, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your websit e. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!
Was this helpful?
Thank you for voting!
oven light glass cover was broken
2 of 2 people found this instruction helpful.
  • wayne from LIMINGTON, ME
  • Really Easy
  • 15 - 30 mins
took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.
Was this helpful?
Thank you for voting!
Bake Element wouldn't heat up to temperature
2 of 2 people found this instruction helpful.
  • John from Foxboro, MA
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
I had viewed the video link on PartsSelect. I removed 2 screws and proceeded to pull element out to disconnect wire connectors. However one side the wire connected was melted on to the contact tab of the element and the wire was broken off. I proceeded to remove back panel from stove and located the exposed broken wire. I stripped back wi re and installed a new wire connector that I had in my tool box. I fed wire through small hole. Then I re-installed back panel. I then connected wires to the new bake element and installed element mounting screws.
Was this helpful?
Thank you for voting!
Cooling fan runs fault code displayed
2 of 2 people found this instruction helpful.
  • FRANK from CLARENCE CTR, NY
  • Easy
  • 30 - 60 mins
  • Screw drivers
Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it eas ily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done
Was this helpful?
Thank you for voting!
f1&f3 error> continuous beeping,oven stopped working after using the self cleaning mode
2 of 2 people found this instruction helpful.
  • Robert from FITCHBURG, MA
  • Easy
  • 30 - 60 mins
  • Nutdriver
I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.
Was this helpful?
Thank you for voting!
Broil element burst
2 of 2 people found this instruction helpful.
  • Ronald from WEST COLUMBIA, SC
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Drop in range was in excellent condition until element burst and was getting ready to purchase another range and then I was looking to replace the element and found part select and they were great from the order process and shipping was fast and the whole process was 5 STARS. As far as me doing the repair I watched the video and it was s imple for even me. I also replaced the bake element at the same time. Once again I highly recommend Part Select and they are second to none.
Was this helpful?
Thank you for voting!
Old end cap broke.
2 of 2 people found this instruction helpful.
  • Travis from North Quincy, MA
  • Really Easy
  • Less than 15 mins
Put the new end cap on and snapped it into place, took about 5 seconds.
Was this helpful?
Thank you for voting!
The above door End Cap broke.
2 of 2 people found this instruction helpful.
  • John from Northglenn, CO
  • Really Easy
  • Less than 15 mins
The repair just required snapping the new part on to the door shelf and then snapping the shelf in to the door.
Was this helpful?
Thank you for voting!
Not cooling and freezer freezing up
6 of 14 people found this instruction helpful.
  • kenneth from carmel, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the condenser cover removed old fan blade defrosted the condenser section installed new blade and reassembled
Was this helpful?
Thank you for voting!
Cap on the door retainer bar broke.
2 of 2 people found this instruction helpful.
  • Mary from New Milford, NJ
  • Really Easy
  • Less than 15 mins
The replacement cap fit perfectly. Unfortunately when the orinigal cap broke it tookout a small piece of the surrounding plastic leaving nothing for the new cap to catch. I have the piece and tried several kinds of glue but nothing holds it securely enough. I would however readily recommend your company. The service was terrific.
Thank you.
Was this helpful?
Thank you for voting!
Broken shelf retainer bar end cap.
2 of 2 people found this instruction helpful.
  • Ruchik from Bronx, NY
  • Really Easy
  • Less than 15 mins
I ordered 2 end caps just to keep one as spare. Turned out I had ordered a size larger than the one already on the refrigerator. So I replaced both ends and it worked fine - with increased shelf space. Now I can even fit a gallon container with ease!!! Took about 20 seconds. I just wish there was an easier way to measure parts before orde ring. Otherwise, the entire process from order to finish took about 3 days.
Was this helpful?
Thank you for voting!
All Instructions for the 3868
121 - 135 of 547