3868 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
burned in half
544 of 548 people
found this instruction helpful.
-
mike from gold bar, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
put the new element in the oven pushed wire onto connector on element held it up to match holes and put the screws back in, very easy to change. I really like the fast way I receive a part from you.
Was this helpful?
Thank you for voting!
No heat - element had burst.
236 of 302 people
found this instruction helpful.
-
John from Marion, IA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Unscrewed 2 screws holding terminal ends of the element in place. Eased the element out, until the two AC power wires were exposed. Pulled off the connectors from the element terminals (pretty tight fit - needed pliers to remove one of them).
Slipped the connectors onto the new element terminals, and eased the element back int ... Read more o the oven wall. Secured the element with the two screws removed previously, and that was pretty much all there was to it. Closed the circuit breakers, and the element tested OK.
Overall, a no-sweat job. One thing, though: I squeezed the oven connectors tight before pushing them back onto the new element. They had loosened up somewhat after pulling them off. A tight connection here seems pretty important, as arcing and corrosion could occur over time if they're too loose.
Slipped the connectors onto the new element terminals, and eased the element back int ... Read more o the oven wall. Secured the element with the two screws removed previously, and that was pretty much all there was to it. Closed the circuit breakers, and the element tested OK.
Overall, a no-sweat job. One thing, though: I squeezed the oven connectors tight before pushing them back onto the new element. They had loosened up somewhat after pulling them off. A tight connection here seems pretty important, as arcing and corrosion could occur over time if they're too loose.
Read less
Was this helpful?
Thank you for voting!
No power to the fan and compressor
222 of 302 people
found this instruction helpful.
-
Christian from Kearneysville, WV
- Really Easy
- Less than 15 mins
-
Screw drivers
I have a fridge in my garage. I have found that a glass of ice water or a cold drink outside is very important to me. When I discovered melting ice dripping onto the garage floor I was very upset. I spun the fridge and found that the compressor and fan weren't starting. I got out my multi-meter and discovered that power was not makin
... Read more
g it to these components. I did some research and found the wiring diagram online. There really isn't too much going on with a fridge and the most likely candidate seemed to be the run capacitor. I ordered the part, replaced it in a few minutes and the fridge began working again.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
F1 code - gas over would not heat.
172 of 188 people
found this instruction helpful.
-
george from birmingham, AL
- Easy
- 15 - 30 mins
-
Screw drivers
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.
Replacing ... Read more the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.
Replacing ... Read more the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.
Read less
Was this helpful?
Thank you for voting!
Oven not holding 350 F, when cooling the coils did not reheat
163 of 215 people
found this instruction helpful.
-
David from Westford, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening,
... Read more
reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Read less
Was this helpful?
Thank you for voting!
Bake element burnt out
132 of 195 people
found this instruction helpful.
-
Glenn from Jupiter, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Before you touch anything unplug the range or trip the breaker. Pull the racks out of the oven, it gives more room to work. Remove the two screws that hold the element and pull the element out about 2-3". Disconnect the old element. Before you install the new element check the wire and the connectors for age and heat damage. If the connec
... Read more
tors are loose replace them (2 connectors @ $1.97 is better than a short in the oven). If the insulation on the wire is degraded (brittle, flaking, brown) consider changing out the wiring. This means opening up the back of the oven and that is another chapter. In most cases you can just re-connect to the replacement element and attach it back to the oven with the two screws. I ran the oven to 400 degrees to just check that everything was OK. Spent a couple extra minutes to check everything out and save yourself pain later.
Read less
Was this helpful?
Thank you for voting!
Heating Element would not heat up for Baking
87 of 91 people
found this instruction helpful.
-
Karen from High Springs, FL
- Easy
- Less than 15 mins
-
Screw drivers
Removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and then replaced the new heating element by connecting the wires and then placing the screws back in. Was a lil difficult because this unit has no oven light and it required a flash light.
Was this helpful?
Thank you for voting!
The Burner was getting too hot and you could not regular the tempature
77 of 89 people
found this instruction helpful.
-
Dennis from Hagerstown, MD
- Really Easy
- Less than 15 mins
-
Screw drivers
Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one
Was this helpful?
Thank you for voting!
F1-1 code
79 of 110 people
found this instruction helpful.
-
charles from marstons mills, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Fa
... Read more
ilure to do so will cause the plastic plug connector to melt from oven heat.
Read less
Was this helpful?
Thank you for voting!
The original heating element shorted and caught fire
89 of 151 people
found this instruction helpful.
-
Eric from Tooele, UT
- Really Easy
- Less than 15 mins
-
Screw drivers
The repair was simple; I removed just two screws, pulled out the wires, and slipped the two spade connectors off the original element. The repair was simply the reverse of the disassembly. The only thing to remember is to throw the circuit breaker before handling the electrical connectors. Other than that, it couldn't be any more strai
... Read more
ght forward.
Read less
Was this helpful?
Thank you for voting!
Needed to replace oven door gasket.
58 of 69 people
found this instruction helpful.
-
Lori from Scottsdale, AZ
- Really Easy
- Less than 15 mins
-
Pliers
First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum.
Was this helpful?
Thank you for voting!
bad light socket
45 of 56 people
found this instruction helpful.
-
nancy from silsbee, TX
- Really Easy
- Less than 15 mins
unplugged refrigerator. removed light bulb from old socket. unsnapped old light socket and pulled it out just enough to diconnect the electrical plug that plugs into the socket . discarded the old socket and plugged in new socket. snapped in new socket into refrigerator. i watched how to do this simple procedure on you tube and decided to
... Read more
do it myself. easy easy easy
Read less
Was this helpful?
Thank you for voting!
Burned terminal block and filter board
95 of 208 people
found this instruction helpful.
-
Joseph from Decatur, GA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench set
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Was this helpful?
Thank you for voting!
Relay
42 of 54 people
found this instruction helpful.
-
John H from Austin, TX
- Really Easy
- 15 - 30 mins
Removed back panel. Opened cover to relay attached to the compressor and pulled off replacing with new relay. No problem.
Better than paying $250 for someone else to do it.
Better than paying $250 for someone else to do it.
Was this helpful?
Thank you for voting!
Repeated oven temperature sensor fault codes.
35 of 43 people
found this instruction helpful.
-
David from Arlington, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the righ
... Read more
t side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.
Read less
Was this helpful?
Thank you for voting!