EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3868 - Instructions

All Instructions for the 3868
76 - 90 of 547

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator to warm
5 of 5 people found this instruction helpful.
  • Lloyd from PITTSBURG, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long
Was this helpful?
Thank you for voting!
Faulty bulb receptacle
10 of 20 people found this instruction helpful.
  • Kenneth from Lynchburg, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!
Was this helpful?
Thank you for voting!
the left front burner burned out & none of the lights to show if a burner was hot would come on.
5 of 5 people found this instruction helpful.
  • Richard from Fair oaks Ranch, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
FIrst we found the power source ( this took us awhile) and cut the power at the fuse box. then we unplugged the cooktop and started to take out screws. It turned out the screw removal had nothing to do with the stove top coming out. We took the taping knife & pried it under a corner and lifted. the cook top was just sitting on the count er.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people found this instruction helpful.
  • Carl from RIVERSIDE, CA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
Oven sensor caused cooling fan to run continuously. Had to flip breaker to get it to turn off..
5 of 5 people found this instruction helpful.
  • Aubrey from EADS, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.
Was this helpful?
Thank you for voting!
Bake Element Failed
5 of 6 people found this instruction helpful.
  • Douglas from Plymouth, WI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplugged the stove. I removed the old element by removing the two screws holding it in, and plugged the stove back in. I ordered the part and it came in 2 days. Unpluged the stove again, connected the new element, and re-attached it via the two screws. Plugged it back in, and it worked great. Fantastic price and quick delivery. Only too k about 5 minutes to fix, and I saved at least $100 by not having to call a service man.
Was this helpful?
Thank you for voting!
6" surface heating coil remained warm when "off"
8 of 15 people found this instruction helpful.
  • William C. from Sealy, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers
Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sl eeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.
Was this helpful?
Thank you for voting!
Variable oven heat and Ignitor. problems
5 of 6 people found this instruction helpful.
  • Floyd from Kenai, AK
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
moved stove away from the wall, Disconnected power, Removed 2 screws on the access panel and removed panel. Disconnected qwick release conections on heat sensor and ignitor, Removed oven door and burner cover to expose ignitor, removed 2 screws to remove ignitor and replaced ignitor. Removed 2 screws and removed sensor, replaced sensor. Reconnected qwick conects on sensor and ignitor. Replaced oven door, burner cover and access panel and checked out. Checks OK !
Was this helpful?
Thank you for voting!
Indicatror Light For 6" Burner Quit Working
5 of 7 people found this instruction helpful.
  • NANCY from LITTLETON, CO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Ok this is a glasstop jenn air cce3531b, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since I had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. Thanks you partselect
Was this helpful?
Thank you for voting!
The lights were on inside however the the water/ice dispenser did not work and the fridge and freezer side was not cooling
5 of 7 people found this instruction helpful.
  • Rickey from DUMAS, AR
  • Really Easy
  • 30 - 60 mins
  • Socket set
Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugge d it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.
Was this helpful?
Thank you for voting!
Left front burner went out.
5 of 7 people found this instruction helpful.
  • Donald from North Highlands, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed 8 screws of retainer holding glass top to box.. Pulled 5 knobs and glass top and set aside. Popped 2 retaining clips holding burner , removed them and transferred to new burner (#12 and #48 position). Used wide blade screwdriver to facilitate removing terminals from old burner and attached terminals to new burner.Popped retaining clips into crossbeam, put glass top on and 8 screws back into retainer. Works great.
Was this helpful?
Thank you for voting!
Oven would not maintain temperature
5 of 7 people found this instruction helpful.
  • KATHY from PLEASANT GAP, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is l ike new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.
Was this helpful?
Thank you for voting!
power light on, but burner not getting hot
7 of 13 people found this instruction helpful.
  • Aaron from Weymouth, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.
Was this helpful?
Thank you for voting!
The 6" heating element stop working on the stove top.
4 of 4 people found this instruction helpful.
  • JULIUS from JACKSON, MI
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First I reviewed a video on YouTube by this site. Even though the range on the video was not the same as mind, it gave me an idea on what to do. I proceeded to pull the rang out from the wall and disconnected the power plug. Next I removed two screws from the back located on the left and used a flat blade screw driver to depress two brack ets on the front to release the glass top panel. I unplugged the wiring harness and disconnected the grounding wire and took the glass panel off and laid it upside down on the kitchen table. I removed the old heating element first by unplugging the wiring and removing the brackets that held it in place. Installed the new one, plugged in all wirings, brackets, screws and replace the top back on the stove.
Was this helpful?
Thank you for voting!
Grandson lost the ignition key to my Toro!
15 of 38 people found this instruction helpful.
  • Michelle from AYLETT, VA
  • Really Easy
  • Less than 15 mins
No repair, lol! Just a perfect fit for my ignition :). I bought two in case my grandson gets curious again.
Was this helpful?
Thank you for voting!
All Instructions for the 3868
76 - 90 of 547