3835 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
end cap to bar of freezer door broke
3 of 4 people
found this instruction helpful.
-
Kimberly A from Columbus, OH
- Really Easy
- Less than 15 mins
Snapped end cap onto bar and installed bar onto freezer door.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
Was this helpful?
Thank you for voting!
Condensor fan blade cracked, blade was sheared off.
3 of 4 people
found this instruction helpful.
-
Bradley from Cedarburg, WI
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
First, remove the cardboard cover on the back, lower portion of the refrigerator.
Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)
Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the b ... Read more lade shaft toward the motor (away from the fan blades) to loosen.
Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.
Reverse the above steps to attach the new blade.
Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)
Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the b ... Read more lade shaft toward the motor (away from the fan blades) to loosen.
Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.
Reverse the above steps to attach the new blade.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
During Hurricane Ike, frig. saw several inched of saltwater and sand underneath. AFter cleaning up, I tried to run and only the blower fan worked. It must have been just above the water. The compressor did not kick on. I looked at the lowest elec. connections and saw corrsion on the overload protect
3 of 4 people
found this instruction helpful.
-
ken from fulshear, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
This was after sitting idle for 9 mos. I simply pulled the part, ordered the same part and installed. Nothing more than a couple of screws and 2 wire connections. It now works great.
Was this helpful?
Thank you for voting!
light wouldn't come out of socket
3 of 5 people
found this instruction helpful.
-
Joyce from Tacoma, WA
- Really Easy
- Less than 15 mins
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this helpful?
Thank you for voting!
Not cooling and freezer freezing up
6 of 14 people
found this instruction helpful.
-
kenneth from carmel, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the condenser cover removed old fan blade defrosted the condenser section installed new blade and reassembled
Was this helpful?
Thank you for voting!
Broken shelf retainer bar end cap.
2 of 2 people
found this instruction helpful.
-
Ruchik from Bronx, NY
- Really Easy
- Less than 15 mins
I ordered 2 end caps just to keep one as spare. Turned out I had ordered a size larger than the one already on the refrigerator. So I replaced both ends and it worked fine - with increased shelf space. Now I can even fit a gallon container with ease!!! Took about 20 seconds. I just wish there was an easier way to measure parts before orde
... Read more
ring. Otherwise, the entire process from order to finish took about 3 days.
Read less
Was this helpful?
Thank you for voting!
Old end cap broke.
2 of 2 people
found this instruction helpful.
-
Travis from North Quincy, MA
- Really Easy
- Less than 15 mins
Put the new end cap on and snapped it into place, took about 5 seconds.
Was this helpful?
Thank you for voting!
The above door End Cap broke.
2 of 2 people
found this instruction helpful.
-
John from Northglenn, CO
- Really Easy
- Less than 15 mins
The repair just required snapping the new part on to the door shelf and then snapping the shelf in to the door.
Was this helpful?
Thank you for voting!
I didn't know if I could get a replacement part, but I googled "replacement parts" (or some such), and since this website looked easy to navigate, chose it. (Actually, I did my ordering via telephone). The sales rep. helped me clarify which part I needed, I ordered it, and received the part the very
2 of 2 people
found this instruction helpful.
-
Kaye from San Francisco, CA
- Really Easy
- Less than 15 mins
I simply snapped the two end pieces into place, attaching the guard rail. It was like putting the pieces of a very easy puzzle together‚ especially for someone like myself who is mechanically challenged.
Was this helpful?
Thank you for voting!
Broken shelf frame
2 of 2 people
found this instruction helpful.
-
Yvonne from FORESTVILLE, NY
- Really Easy
- Less than 15 mins
Easy
Was this helpful?
Thank you for voting!
Shelf was cracked on both sides
2 of 2 people
found this instruction helpful.
-
Marcella from SPRINGFIELD, MA
- Really Easy
- Less than 15 mins
I first washed old shelf to make sure glass will easily slip out. Installed old glass and replaced.
Was this helpful?
Thank you for voting!
Cap on the door retainer bar broke.
2 of 2 people
found this instruction helpful.
-
Mary from New Milford, NJ
- Really Easy
- Less than 15 mins
The replacement cap fit perfectly. Unfortunately when the orinigal cap broke it tookout a small piece of the surrounding plastic leaving nothing for the new cap to catch. I have the piece and tried several kinds of glue but nothing holds it securely enough. I would however readily recommend your company. The service was terrific.
... Read more Thank you.
... Read more Thank you.
Read less
Was this helpful?
Thank you for voting!
Was getting too cold
2 of 2 people
found this instruction helpful.
-
Jose A from WEST PALM BCH, FL
- Very Easy
- Less than 15 mins
-
Screw drivers
Was only two screws after that carefully took the part away unplugging the wires at the same time was plugging in to the new part and was done after 5 or 7 min
Was this helpful?
Thank you for voting!
light kept blinking on and off never same way
2 of 2 people
found this instruction helpful.
-
michael from CENTRALIA, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends
Other Parts Used:
Was this helpful?
Thank you for voting!
the old shelf was brittle and breaking off in the front support corners.
2 of 2 people
found this instruction helpful.
-
Kim from LABELLE, FL
- Very Easy
- Less than 15 mins
I ordered the new part from PartSelect and it was delivered very quickly. I removed the part from the box, laid the old glass shelf inside if it and placed it in the fridge. No tools required, and then slid the vegetable drawers into it and replaced the food. Very satisfied with my purchase experience.
Was this helpful?
Thank you for voting!