EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3835 - Instructions

All Instructions for the 3835
91 - 105 of 358

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
noise from fan blade hitting refrigerator interior panel.
4 of 4 people found this instruction helpful.
  • Dennis from LEHIGHTON, PA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
The hardest part of the repair was emptying the freezer, next was getting the fan off of the motor shaft, The only reason the job was difficult is because i am 67 years old and not as flexible as i used to be.I had a tough time getting the fan off of the motor shaft, but i got it off with the use of a vise, and had to use the hammer and a socket to install a new fan blade.
Was this helpful?
Thank you for voting!
Install rear wheel
4 of 4 people found this instruction helpful.
  • Bruce from COLUSA, CA
  • Very Difficult
  • More than 2 hours
I haven’t received the wheel yet. Originally ordered on Dec. 13. Hadn’t received it by Dec. 20. Finally shipped on Dec. 22. Tracking said it was expected to be delivered on Jan.2. Not delivered. Then it said it was still on its way but it was unknown when it would be delivered. Still waiting on Jan. 6. By far the most expensive e conomy shipping ever, as this refrigerator is in a rental that can’t be rented until a wheel is installed.
Was this helpful?
Thank you for voting!
Difficulty in removing the old switch
5 of 8 people found this instruction helpful.
  • James from Federal Way, AL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.
Was this helpful?
Thank you for voting!
Refrigerator light wouldn't come on.
4 of 5 people found this instruction helpful.
  • Daniel from Crown Point, IN
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.
Was this helpful?
Thank you for voting!
Fridge doesn't cool properly; freezer iced up
4 of 5 people found this instruction helpful.
  • Will from Houston, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver
You will need a 1/4" nut driver or socket & extension.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.
Was this helpful?
Thank you for voting!
The food door gasket was not doing its función properly.
4 of 5 people found this instruction helpful.
  • ROBERTO SOLIS PTY from MIAMI, FL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Well, when I opened the package the gasket was bended in half so I opened it and put it first on the floor and after some minutes I put it on the refrigerator side.
Then I took a screwdriver and easily removed the old gasket, cleaned the the channel where the new gasket had to seat or be inserted. Then I took the new gasket and put it on place and begining on the top right corner I began to insert the gasket into the channel from the right to the left. Double check to see if was ok
I continued on both sides from top to the bottom, one by one.
When I reached the bottom I began from the left to the right inserting the gasket into the channel. To complete the installation at the bottom I had to pull the gasket a little to properly reach the corner and I finished
To make sure the gasket was on place I hit the gasket with my bare hand all around and I was done.
It was very easy, I just followed the instructions given by the manufacturer
Was this helpful?
Thank you for voting!
Old timer quit working.
7 of 14 people found this instruction helpful.
  • John from Mesa, AZ
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Installed the new timer.
Was this helpful?
Thank you for voting!
Broken vegetable pan cover
4 of 5 people found this instruction helpful.
  • Luis from Washington, DC
  • Really Easy
  • Less than 15 mins
The part was delivered promptly. Then, to quote Raymond from Georgia:
I pulled the old one out, and put the new one in.
Was this helpful?
Thank you for voting!
Interior Light did not go on due to faulty switch
4 of 6 people found this instruction helpful.
  • Robert from Coto de Caza, CA
  • Really Easy
  • Less than 15 mins
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this helpful?
Thank you for voting!
the frame was broken and it made using the shelf for food storage difficult.
3 of 3 people found this instruction helpful.
  • martha from Lehigh Acres, FL
  • Very Easy
  • Less than 15 mins
Emptied the lower area of food, removed the drawers and the removed the broken shelf frame. My glass was unbroken so after removing it from the broken frame and cleaning it, I just had to place it in the new frame and put it in the frig. Can't believe how easy and quick the whole process was. I can now utilized all that wasted space in my frig again.
Was this helpful?
Thank you for voting!
replace broken door dairy
3 of 3 people found this instruction helpful.
  • Edwin from BELLINGHAM, WA
  • Very Easy
  • Less than 15 mins
a-ok. no problems
Was this helpful?
Thank you for voting!
The unit cycles but does not achieve proper temperature
3 of 3 people found this instruction helpful.
  • Anthony from COVINGTON, LA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Remove power from the unit. With short length #2 Phillips loosen and remove the two(2) screws on the control panel located center top of the refrigeration area. Slide the control panel back about 1/2 inch and allow it to dangle from its wiring harness. Pinch the locking tab on the harness connector with one hand and use the other hand to separate the two sides. A little force is required. Remove the control panel from the refrigerator and shut the refrigerator door. Examine and note the routing of the temperature probe (Silver colored flexible wire) take a picture for later reference. Remove the old and replace with new unit. route temperature probe like the replaced unit. Reverse the steps and reinstall the control panel. It is a good idea to also purchase and replace the defrost timer.
Was this helpful?
Thank you for voting!
the evaporator fan motor was making noise sometimes, but not all the time during the cooling cycle
3 of 3 people found this instruction helpful.
  • Kenneth from SEATTLE, WA
  • Really Easy
  • 15 - 30 mins
  • Socket set
after watching how easy it was to get to the evaporator fan motor on u-tube, I took out the motor to inspect it......the motor had about 1/8 inch shaft end play and a slight amount of play on the shaft, the rubber grommets looked OK.....I then put it back together......since the motor was the only moving part in this location I figured it had to be the part making the noise, so I ordered a motor and 2 grommets …...the replacement motor also had 1/8 inch end play on the shaft, but no play on the shaft....I installed the new parts and it has been a week now and no noise.....SUCCESS!...….the shaft on the motor protrudes from the motor, and the fan is mounted about 1 1/4 inch away from the bearing in the motor and the fan is unsupported, so I ASSUME that the slight amount of play on the shaft caused some harmonics which caused it to make noise some of the time, but not all of the time......
Was this helpful?
Thank you for voting!
NOISE FROM THE FREEZER SECTION OF THE REFRIGERATOR
3 of 3 people found this instruction helpful.
  • Sarafina from DEWEY, AZ
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
1) TURNED POWER OFF FROM REFRIGERATOR 2) REMOVED THE FREEZER SHELF FIRST BY GENTLY TAPPING THE LEFT SIDE UP AND OUT THEN THE RIGHT SIDE UP AND OUT 3) REMOVED THE 2 PHILLIPS SCREWS HOLDING THE EVAPORATIVE FAN COVER IN PLACE 4) GENTLY PUSHED THE COVER UP AND MAKING SURE THE 2 CLIPS WERE NOT DAMAGED 5) VERY GENTLY PUSHED UP ON THE STYRO FOA M SHIELD GRASPING IT FROM THE BOTTOM, BE VERY CAREFUL NOT TO CRACK OR DAMAGE THIS 6) THEN REMOVED 4 OF THE PHILLIPS SCREWS HOLDING THE BACK PANEL 7) THEN REMOVED THE 2 SCREWS HOLDING THE FAN MOTOR IN POSITION ON THE BACK COVER AND LAID THAT ASIDE 8) I COULD THEN SEE THE MOTOR SO I UNCLIPPED THE RED/DARK WIRE CLIP FROM THE HARNESS WITH MY FINGERS, THEN TOOK MY NEEDLE NOSE PLIERS AND GENTLY PULLED UP ON THE GREEN GROUND WIRE 9) I THEN REMOVED THE 2 PHILLIPS HEAD SCREWS HOLDING THE MOTOR BRACKET TO THE WALL OF THE FREEZER 10) THEN REMOVED THE ENTIRE MOTOR AND PUT THAT ON THE KITCHEN TABLE 11) TOOK MY NEEDLE NOSE PLIERS AND VERY, VERY GENTLY PRIED OFF THAT LITTLE METAL RING HOLDING THE FAN BLADE ON (TRICKY SO LEFT UP GENTLY)...I BOUGHT ADDITIONAL IN CASE I DAMAGED IT 12) TOOK MY 5/16 NUT DRIVER AND UNSCREWED THE TOP METAL BRACKET HOLDING THE MOTOR 13) LIFTED THE MOTOR OFF AND LOOKED AT THE TOP AND BOTTOM GROMMETS TO SEE IF DAMAGED OR CRACKED (I BOUGHT ADDITIONAL GROMMETS IN CASE THEY WERE CRACKED OR DAMAGED, EASY FIX) 14) THEN ATTACHED THE NEW MOTOR AND BASICALLY SIMPLY DID EVERYTHING IN REVERSE TO INSTALL THE NEW MOTOR. MAKE SURE YOU KEEP YOUR SCREWS IN ORDER SO YOU CAN IDENTIFY WHICH PART THEY CAME FROM. MAKE SURE YOU DO NOT PINCH AND WIRES WHEN RE-INSTALLING THE MOTOR. SAVED ME A REPAIR PERSON CALL.
Was this helpful?
Thank you for voting!
broken Vegetable drawer frame
3 of 3 people found this instruction helpful.
  • Helen from PASO ROBLES, CA
  • Really Easy
  • 30 - 60 mins
Ordered the frame and put it in.
Was this helpful?
Thank you for voting!
All Instructions for the 3835
91 - 105 of 358