3835 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
freezer compartment worked fine but very little cooling going to refrigerator section.
3 of 3 people
found this instruction helpful.
-
Lee from OZARK, AR
- Really Easy
- 30 - 60 mins
-
Screw drivers
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The re
... Read more
placement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Read less
Was this helpful?
Thank you for voting!
noisy fan
4 of 6 people
found this instruction helpful.
-
ronald from springfield, VT
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
removed cover over fan, four screws. removed two screws ,that holds fan in place,removed two more screws that holds fan in bracket,then reinstalled
Was this helpful?
Thank you for voting!
intermittent loud screeching,,humming sound
3 of 3 people
found this instruction helpful.
-
LARRY. T from KNOXVILLE, TN
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
removed food from freezer section removed fan guard, partially remove ice maker, remove back panel, then fan assembly,disaasembled fan motor from brackets, fan from motor, grommet from bracket. assembled grommet in bracket, fan blade on motor, motor in bracket, fan assembly back in compartment, installed back panel,then ice maker, replace
... Read more
d fan guard and food. no more noise.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Plastic bracket broke so vegetable drawer would no longer stay in place
3 of 3 people
found this instruction helpful.
-
jim from CORNING, NY
- Really Easy
- 30 - 60 mins
Pipes out the glass from existing shelf while in place inside refrigerator. Remove broken shelf. Install new shelf. Clean and replace glass. Easy job thanks to finding the correct part from Part Select!
Was this helpful?
Thank you for voting!
Fan not working
3 of 3 people
found this instruction helpful.
-
joan from STERLING HTS, MI
- Easy
- 1- 2 hours
-
Screw drivers, Socket set
Took out old put new in. Watched a u tube, no problems
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken Vegetable Drawer Shelf Frame
3 of 3 people
found this instruction helpful.
-
Laura from CRAIGVILLE, IN
- Really Easy
- 30 - 60 mins
I took the broken piece out and replace it with the new replacement shelf
Was this helpful?
Thank you for voting!
Compressor would randomly not turn on. Fridge too warm sometimes.
3 of 4 people
found this instruction helpful.
-
Mackenzie from Williston, ND
- Really Easy
- 30 - 60 mins
-
Screw drivers
Replace temperature control. That fixed it. Also, removed plastic bag obstructing air vent in freezer which added performance. Fridge works good now.
Was this helpful?
Thank you for voting!
gasket was not easily fitted
3 of 4 people
found this instruction helpful.
-
neal j from COLUMBIA, SC
- Very Difficult
- More than 2 hours
I did not do the repair but observed a friend trying to replace gasket in refrigerator. It was a very difficult procedure. He works as a handyman so he knew what he was doing and had to manually fit gasket with some help with a hammer. Gasket did not go in easy and had to be forced to fit until job completed/
Was this helpful?
Thank you for voting!
Replace the door gasket on the freezer door of my top-freezer refrigerator
3 of 4 people
found this instruction helpful.
-
Scott from NAPLES, FL
- Very Difficult
- 1- 2 hours
-
Socket set
Removed the door by removing the two screws holding it on. Do not try to do this repair with the door attached. Easily removed the old gasket. Getting the new one on the door was EXTREMELY difficult. I couldn't do it. After 90 minutes, I gave up and called my appliance repairman. When he arrived, he and I worked together to get the new ga
... Read more
sket on the door. It took 2 sets of hands to do this. It still took us about 40 minutes. My repairman had a few choice words about the design of the system holding the gasket on the door. Ditto for me. So the cost of my repair was doubled because I had to pay the repairman to help me attach the new gasket. I should have just bought a new fridge.
Read less
Was this helpful?
Thank you for voting!
switchlight on my refrigerator was not working
5 of 10 people
found this instruction helpful.
-
Eileen from Coto de Caza, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point,
... Read more
it was just a matter of plugging in the new switchlight , which was very simple.
Read less
Was this helpful?
Thank you for voting!
Could not adjust temperature
3 of 4 people
found this instruction helpful.
-
Boyd from Blaine, WA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Replaced temp controller
Was this helpful?
Thank you for voting!
was not defrosting
3 of 4 people
found this instruction helpful.
-
denis from freedom, NH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
first i removed all the screws inside the freezer compartment took out theback and bottom to get to the evap motor,unpluged the wires and removed the evap motor ,removed the fan from old unit and put it on the new unit them mounted it to the back wall of the fridge,,, and put back top and bottom
Was this helpful?
Thank you for voting!
Fridge never cuts off.freeze everything inside of fridge.
3 of 4 people
found this instruction helpful.
-
Henry from DOUGLASVILLE, GA
- Very Easy
- Less than 15 mins
-
Screw drivers
To remove the temp sensor.2 Phillip head screws not remove the cover inside fridge .the temp control knob cover.removed that and unplugged switch.installed new switch.reinstalled cover.
Was this helpful?
Thank you for voting!
Freezer was not freezing food.
3 of 4 people
found this instruction helpful.
-
Steve from Ridgecrest, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Inspected freezer because food was not freezing, getting cold, but not freezing. Noticed fan was not blowing air, but making a little motor noise, like it's trying to turn. Removed cover panel, and found the fan blade rubbing on the panel, fan shaft was worn out and very loose, wobley. That told me the fan needed to be replaced. Found par
... Read more
t on the GE Partselect website and ordered the parts via the website order process. This was easy. The parts were shipped quickley and were at my front door the next day. Couldn't believe it. The actual process was very easy: Remove cover, remove bracket holding fan motor, remove and replace motor, re-assemble parts. About 20-25 minutes from start to finish. Freezer is working like it's suppose to.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
drain freezing up found cond fan not working
3 of 4 people
found this instruction helpful.
-
glenn from la harpe, KS
- Really Easy
- Less than 15 mins
Cleaned oh t freezer removed floor. Removed back inside wall removed and replaced fan and put back removed parts
L
L
Was this helpful?
Thank you for voting!