3834 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
replace broken door dairy
3 of 3 people
found this instruction helpful.
-
Edwin from BELLINGHAM, WA
- Very Easy
- Less than 15 mins
a-ok. no problems
Was this helpful?
Thank you for voting!
The unit cycles but does not achieve proper temperature
3 of 3 people
found this instruction helpful.
-
Anthony from COVINGTON, LA
- Very Easy
- Less than 15 mins
-
Screw drivers
Remove power from the unit. With short length #2 Phillips loosen and remove the two(2) screws on the control panel located center top of the refrigeration area. Slide the control panel back about 1/2 inch and allow it to dangle from its wiring harness. Pinch the locking tab on the harness connector with one hand and use the other hand to
... Read more
separate the two sides. A little force is required. Remove the control panel from the refrigerator and shut the refrigerator door. Examine and note the routing of the temperature probe (Silver colored flexible wire) take a picture for later reference. Remove the old and replace with new unit. route temperature probe like the replaced unit. Reverse the steps and reinstall the control panel. It is a good idea to also purchase and replace the defrost timer.
Read less
Was this helpful?
Thank you for voting!
the evaporator fan motor was making noise sometimes, but not all the time during the cooling cycle
3 of 3 people
found this instruction helpful.
-
Kenneth from SEATTLE, WA
- Really Easy
- 15 - 30 mins
-
Socket set
after watching how easy it was to get to the evaporator fan motor on u-tube, I took out the motor to inspect it......the motor had about 1/8 inch shaft end play and a slight amount of play on the shaft, the rubber grommets looked OK.....I then put it back together......since the motor was the only moving part in this location I figured it
... Read more
had to be the part making the noise, so I ordered a motor and 2 grommets …...the replacement motor also had 1/8 inch end play on the shaft, but no play on the shaft....I installed the new parts and it has been a week now and no noise.....SUCCESS!...….the shaft on the motor protrudes from the motor, and the fan is mounted about 1 1/4 inch away from the bearing in the motor and the fan is unsupported, so I ASSUME that the slight amount of play on the shaft caused some harmonics which caused it to make noise some of the time, but not all of the time......
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Interior Light did not go on due to faulty switch
4 of 6 people
found this instruction helpful.
-
Robert from Coto de Caza, CA
- Really Easy
- Less than 15 mins
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this helpful?
Thank you for voting!
noisy fan
4 of 6 people
found this instruction helpful.
-
ronald from springfield, VT
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
removed cover over fan, four screws. removed two screws ,that holds fan in place,removed two more screws that holds fan in bracket,then reinstalled
Was this helpful?
Thank you for voting!
intermittent loud screeching,,humming sound
3 of 3 people
found this instruction helpful.
-
LARRY. T from KNOXVILLE, TN
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
removed food from freezer section removed fan guard, partially remove ice maker, remove back panel, then fan assembly,disaasembled fan motor from brackets, fan from motor, grommet from bracket. assembled grommet in bracket, fan blade on motor, motor in bracket, fan assembly back in compartment, installed back panel,then ice maker, replace
... Read more
d fan guard and food. no more noise.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
freezer compartment worked fine but very little cooling going to refrigerator section.
3 of 3 people
found this instruction helpful.
-
Lee from OZARK, AR
- Really Easy
- 30 - 60 mins
-
Screw drivers
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The re
... Read more
placement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Read less
Was this helpful?
Thank you for voting!
Fan not working
3 of 3 people
found this instruction helpful.
-
joan from STERLING HTS, MI
- Easy
- 1- 2 hours
-
Screw drivers, Socket set
Took out old put new in. Watched a u tube, no problems
Other Parts Used:
Was this helpful?
Thank you for voting!
NOISE FROM THE FREEZER SECTION OF THE REFRIGERATOR
3 of 3 people
found this instruction helpful.
-
Sarafina from DEWEY, AZ
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
1) TURNED POWER OFF FROM REFRIGERATOR 2) REMOVED THE FREEZER SHELF FIRST BY GENTLY TAPPING THE LEFT SIDE UP AND OUT THEN THE RIGHT SIDE UP AND OUT 3) REMOVED THE 2 PHILLIPS SCREWS HOLDING THE EVAPORATIVE FAN COVER IN PLACE 4) GENTLY PUSHED THE COVER UP AND MAKING SURE THE 2 CLIPS WERE NOT DAMAGED 5) VERY GENTLY PUSHED UP ON THE STYRO FOA
... Read more
M SHIELD GRASPING IT FROM THE BOTTOM, BE VERY CAREFUL NOT TO CRACK OR DAMAGE THIS 6) THEN REMOVED 4 OF THE PHILLIPS SCREWS HOLDING THE BACK PANEL 7) THEN REMOVED THE 2 SCREWS HOLDING THE FAN MOTOR IN POSITION ON THE BACK COVER AND LAID THAT ASIDE 8) I COULD THEN SEE THE MOTOR SO I UNCLIPPED THE RED/DARK WIRE CLIP FROM THE HARNESS WITH MY FINGERS, THEN TOOK MY NEEDLE NOSE PLIERS AND GENTLY PULLED UP ON THE GREEN GROUND WIRE 9) I THEN REMOVED THE 2 PHILLIPS HEAD SCREWS HOLDING THE MOTOR BRACKET TO THE WALL OF THE FREEZER 10) THEN REMOVED THE ENTIRE MOTOR AND PUT THAT ON THE KITCHEN TABLE 11) TOOK MY NEEDLE NOSE PLIERS AND VERY, VERY GENTLY PRIED OFF THAT LITTLE METAL RING HOLDING THE FAN BLADE ON (TRICKY SO LEFT UP GENTLY)...I BOUGHT ADDITIONAL IN CASE I DAMAGED IT 12) TOOK MY 5/16 NUT DRIVER AND UNSCREWED THE TOP METAL BRACKET HOLDING THE MOTOR 13) LIFTED THE MOTOR OFF AND LOOKED AT THE TOP AND BOTTOM GROMMETS TO SEE IF DAMAGED OR CRACKED (I BOUGHT ADDITIONAL GROMMETS IN CASE THEY WERE CRACKED OR DAMAGED, EASY FIX) 14) THEN ATTACHED THE NEW MOTOR AND BASICALLY SIMPLY DID EVERYTHING IN REVERSE TO INSTALL THE NEW MOTOR. MAKE SURE YOU KEEP YOUR SCREWS IN ORDER SO YOU CAN IDENTIFY WHICH PART THEY CAME FROM. MAKE SURE YOU DO NOT PINCH AND WIRES WHEN RE-INSTALLING THE MOTOR. SAVED ME A REPAIR PERSON CALL.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Compressor would randomly not turn on. Fridge too warm sometimes.
3 of 4 people
found this instruction helpful.
-
Mackenzie from Williston, ND
- Really Easy
- 30 - 60 mins
-
Screw drivers
Replace temperature control. That fixed it. Also, removed plastic bag obstructing air vent in freezer which added performance. Fridge works good now.
Was this helpful?
Thank you for voting!
Replace the door gasket on the freezer door of my top-freezer refrigerator
3 of 4 people
found this instruction helpful.
-
Scott from NAPLES, FL
- Very Difficult
- 1- 2 hours
-
Socket set
Removed the door by removing the two screws holding it on. Do not try to do this repair with the door attached. Easily removed the old gasket. Getting the new one on the door was EXTREMELY difficult. I couldn't do it. After 90 minutes, I gave up and called my appliance repairman. When he arrived, he and I worked together to get the new ga
... Read more
sket on the door. It took 2 sets of hands to do this. It still took us about 40 minutes. My repairman had a few choice words about the design of the system holding the gasket on the door. Ditto for me. So the cost of my repair was doubled because I had to pay the repairman to help me attach the new gasket. I should have just bought a new fridge.
Read less
Was this helpful?
Thank you for voting!
gasket was not easily fitted
3 of 4 people
found this instruction helpful.
-
neal j from COLUMBIA, SC
- Very Difficult
- More than 2 hours
I did not do the repair but observed a friend trying to replace gasket in refrigerator. It was a very difficult procedure. He works as a handyman so he knew what he was doing and had to manually fit gasket with some help with a hammer. Gasket did not go in easy and had to be forced to fit until job completed/
Was this helpful?
Thank you for voting!
Rear flap had deteriorated.
3 of 4 people
found this instruction helpful.
-
David from PITTSBURGH, PA
- A Bit Difficult
- 30 - 60 mins
-
Pliers
Grip each retaining clip next to the housing with large pliers. Squeeze clip completely and pull straight out. Important: Do not attempt to bend clip up or down as clip may bend and become very difficult to remove. When old flap is removed, mower edge can be cleaned and painted to avoid rust. Install new flap in same direction front/rear
... Read more
as removed flap. Reinstall clips in same direction as they were, as up and down sides are not the same.
Read less
Was this helpful?
Thank you for voting!
switchlight on my refrigerator was not working
5 of 10 people
found this instruction helpful.
-
Eileen from Coto de Caza, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point,
... Read more
it was just a matter of plugging in the new switchlight , which was very simple.
Read less
Was this helpful?
Thank you for voting!
was not defrosting
3 of 4 people
found this instruction helpful.
-
denis from freedom, NH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
first i removed all the screws inside the freezer compartment took out theback and bottom to get to the evap motor,unpluged the wires and removed the evap motor ,removed the fan from old unit and put it on the new unit them mounted it to the back wall of the fridge,,, and put back top and bottom
Was this helpful?
Thank you for voting!