3834 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer door would not close all the way.
4 of 4 people
found this instruction helpful.
-
Paul from LINCOLN, DE
- Very Easy
- Less than 15 mins
-
Socket set
Pulled the door off easily and noticed that the spacer on the Center hinge was ground down to nothing and that a small screw in the bottom plate of the door was half way out. This screw would catch on the cabinet Center hinge bracket and stopped the door from closing. Problem was solved by tightening the screw and putting in a new "spac
... Read more
er" that kept the small screws from contacting the Center hinge bracket. The freezer door now closes like new.
Read less
Was this helpful?
Thank you for voting!
missing a shelf
6 of 10 people
found this instruction helpful.
-
Joseph from Rome, NY
- Really Easy
- Less than 15 mins
My repair was simple. Just put the shelf in the holes in the freezer. The AMAZING thing was how quickly I recieved the part after placing my order. I placed the order at about 3:30 pm on a friday checked the box for ground shipping and the part was at my door the next morning. I think that was a mistake, but I was impressed.
Was this helpful?
Thank you for voting!
freezer cold but refrigerator warm, would not cycle the defrost on freezer
4 of 4 people
found this instruction helpful.
-
MATT from OAKLAND, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
two screws and a connector were removed to replace the timer.
Timer was located on the top front of fridge
Timer was located on the top front of fridge
Was this helpful?
Thank you for voting!
Freezer door gasket was not sealing
4 of 4 people
found this instruction helpful.
-
Reginald from VERO BEACH, FL
- Really Easy
- Less than 15 mins
Went on YouTube and it had excellent instructions for removal and installation
Was this helpful?
Thank you for voting!
top freezer working, bottom section of the fridge not cooling
6 of 10 people
found this instruction helpful.
-
Michael from Jamaica, NY
- Easy
- 15 - 30 mins
-
Screw drivers
First I removed the two screws, the fan and unpluged the electrical connection. Then, plugged in the new part and then screw it back together.
Was this helpful?
Thank you for voting!
Bad defrost timer
5 of 7 people
found this instruction helpful.
-
Bruce from Silver Spring, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers
Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.
I'll be back...
I'll be back...
Was this helpful?
Thank you for voting!
Howling motor
4 of 4 people
found this instruction helpful.
-
Gregg from COEUR D ALENE, ID
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver
Open freezer, remove rack....this got a little complicated because I had to remove the door, that required the offset screwdriver because I had a clearance issues preventing the door from opening all the way. Remove the panel covering the fan, unplug the fan, remove it from bracket, install new fan, plug in, replace panel, replace rack, r
... Read more
eplace door...bam all done!
Read less
Was this helpful?
Thank you for voting!
The lights were on inside however the the water/ice dispenser did not work and the fridge and freezer side was not cooling
5 of 7 people
found this instruction helpful.
-
Rickey from DUMAS, AR
- Really Easy
- 30 - 60 mins
-
Socket set
Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugge
... Read more
d it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.
Read less
Was this helpful?
Thank you for voting!
Install rear wheel
4 of 4 people
found this instruction helpful.
-
Bruce from COLUSA, CA
- Very Difficult
- More than 2 hours
I haven’t received the wheel yet. Originally ordered on Dec. 13. Hadn’t received it by Dec. 20. Finally shipped on Dec. 22. Tracking said it was expected to be delivered on Jan.2. Not delivered. Then it said it was still on its way but it was unknown when it would be delivered. Still waiting on Jan. 6. By far the most expensive e
... Read more
conomy shipping ever, as this refrigerator is in a rental that can’t be rented until a wheel is installed.
Read less
Was this helpful?
Thank you for voting!
noise from fan blade hitting refrigerator interior panel.
4 of 4 people
found this instruction helpful.
-
Dennis from LEHIGHTON, PA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
The hardest part of the repair was emptying the freezer, next was getting the fan off of the motor shaft, The only reason the job was difficult is because i am 67 years old and not as flexible as i used to be.I had a tough time getting the fan off of the motor shaft, but i got it off with the use of a vise, and had to use the hammer and a
... Read more
socket to install a new fan blade.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Refrigerator light wouldn't come on.
4 of 5 people
found this instruction helpful.
-
Daniel from Crown Point, IN
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.
Was this helpful?
Thank you for voting!
Difficulty in removing the old switch
5 of 8 people
found this instruction helpful.
-
James from Federal Way, AL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around.
... Read more
If i had ordered the replacement before and not afterwards I would have seen this before hand.
Read less
Was this helpful?
Thank you for voting!
Fridge doesn't cool properly; freezer iced up
4 of 5 people
found this instruction helpful.
-
Will from Houston, TX
- Easy
- 15 - 30 mins
-
Nutdriver
You will need a 1/4" nut driver or socket & extension.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.
Was this helpful?
Thank you for voting!
The food door gasket was not doing its función properly.
4 of 5 people
found this instruction helpful.
-
ROBERTO SOLIS PTY from MIAMI, FL
- Very Easy
- Less than 15 mins
-
Screw drivers
Well, when I opened the package the gasket was bended in half so I opened it and put it first on the floor and after some minutes I put it on the refrigerator side.
Then I took a screwdriver and easily removed the old gasket, cleaned the the channel where the new gasket had to seat or be inserted. Then I took the new gasket and put ... Read more it on place and begining on the top right corner I began to insert the gasket into the channel from the right to the left. Double check to see if was ok
I continued on both sides from top to the bottom, one by one.
When I reached the bottom I began from the left to the right inserting the gasket into the channel. To complete the installation at the bottom I had to pull the gasket a little to properly reach the corner and I finished
To make sure the gasket was on place I hit the gasket with my bare hand all around and I was done.
It was very easy, I just followed the instructions given by the manufacturer
Then I took a screwdriver and easily removed the old gasket, cleaned the the channel where the new gasket had to seat or be inserted. Then I took the new gasket and put ... Read more it on place and begining on the top right corner I began to insert the gasket into the channel from the right to the left. Double check to see if was ok
I continued on both sides from top to the bottom, one by one.
When I reached the bottom I began from the left to the right inserting the gasket into the channel. To complete the installation at the bottom I had to pull the gasket a little to properly reach the corner and I finished
To make sure the gasket was on place I hit the gasket with my bare hand all around and I was done.
It was very easy, I just followed the instructions given by the manufacturer
Read less
Was this helpful?
Thank you for voting!
Old timer quit working.
7 of 14 people
found this instruction helpful.
-
John from Mesa, AZ
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Installed the new timer.
Was this helpful?
Thank you for voting!