38187 General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The light inside the oven had burned out
3 of 7 people
found this instruction helpful.
-
Catherine from SEATTLE, WA
- Very Easy
- Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
Fan was getting really noisy.
1 person
found this instruction helpful.
-
frankie from Port Richey, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
Looked at fan and seen it was rubbing metal cage. After looking and checking fan noticed bushings were worn letting fan hit cage. Repair was very easy. Used a 1/4 inch nut driver to remove bracket holding fan. Pulled fan blade off shaft by just pulling it forward. Removed fan and replaced grommets. Reassembled fan and fan blade. Took
... Read more
just 10 minutes.
Read less
Was this helpful?
Thank you for voting!
Supports for vegetable baskets broken
2 of 4 people
found this instruction helpful.
-
Marian from Chapel Hill, NC
- Difficult
- 15 - 30 mins
Installed it by hand with my son and myself. Hard ot figure it out and found another part broken. Did not figure out how the screws went in or what they attached to.
Other Parts Used:
Was this helpful?
Thank you for voting!
Noisy Freezer Evaporator
1 person
found this instruction helpful.
-
Brian from BOZEMAN, MT
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 ... Read more years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 ... Read more years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Light was flicking
1 of 2 people
found this instruction helpful.
-
Stephanie from KEARNY, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
It was way to ez to install only a couple of minutes that's it
Was this helpful?
Thank you for voting!
Broken light switch
1 of 2 people
found this instruction helpful.
-
Ted from SANDWICH, IL
- Easy
- 15 - 30 mins
-
Screw drivers
took a little more effort than the video show to remove old module and replace new. Works fine now.
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people
found this instruction helpful.
-
Louis from LEAGUE CITY, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
Easy
Was this helpful?
Thank you for voting!
The door activated light switch was missing.
1 of 3 people
found this instruction helpful.
-
Don from Eugene, OR
- Really Easy
- Less than 15 mins
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this helpful?
Thank you for voting!
Fan stopped working, Ice maker burned out
0 of 1 people
found this instruction helpful.
-
TODD from PLAINVILLE, CT
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Fan Quit So did the Ice Maker. $150.00 worth of parts plus my time. Also the Freezer Floor cracked for some stupid reason.
Other Parts Used:
Was this helpful?
Thank you for voting!
Bad switch for door prevented interior light from coming on
0 of 1 people
found this instruction helpful.
-
Patricia from Sylva, NC
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of yo
... Read more
ur company & it's repair video. THANK YOU SO MUCH
Read less
Was this helpful?
Thank you for voting!
The evaporator fan in the freezer compartment began making a loud noise.
0 of 1 people
found this instruction helpful.
-
Boyd from Rapid City, SD
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people
found this instruction helpful.
-
Roscoe G from ROCHESTER, NY
- Very Easy
- Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
Cracked Dairy Door
0 of 3 people
found this instruction helpful.
-
Fr Kerry from Washington, DC
- Really Easy
- Less than 15 mins
PartSelect shipped me the part and it arrived in less than 3 days. It took longer to unwrap the excellent packing than it did to pop the new door into place. Wonderful!
Was this helpful?
Thank you for voting!
Center slide missing on crisper drawer
0 of 4 people
found this instruction helpful.
-
Deanna from Glendale, AZ
- Really Easy
- Less than 15 mins
Took out the drawers slipped the new track into place and replaced the drawers.
Was this helpful?
Thank you for voting!
light in freezer section not working
6 of 24 people
found this instruction helpful.
-
Victor from Fort Myers, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks
Was this helpful?
Thank you for voting!