38187 General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
A power surge made my side by side refrigerator stop working
-
Country at from SAYRE, OK
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I started at the compressor and replaced the overload and the Ptcr first and that did not make the compressor start running again, so I replaced the capasitor and it still did not start, so I bit the bulett and replaced the Main Control Board and that is what I should have checked first, when I removed the old one I found a little burnt s
... Read more
pot on the back that I could not see from the front. The new one did not look exactly like the old one, it had two more wire terminals than the old one, but just leave them blank and everything will work just fine!
Read less
Was this helpful?
Thank you for voting!
install second set pan sliders
-
William from Rockville, MD
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Because the kit did not include fasteners, had to use wood screws and superglue.
Other Parts Used:
Was this helpful?
Thank you for voting!
Compressor not coming on
-
Kevin from Morris, IL
- Easy
- 15 - 30 mins
-
Nutdriver
Had to e-mail GE for electrical schematic. Checked voltages to compressor. Jumpered compressor to see if it would even come on. Found bad run capacitor. Fixed.
Was this helpful?
Thank you for voting!
broking slide
-
Anthony from Painter, VA
- Easy
- 15 - 30 mins
replace the bar lift top off
Was this helpful?
Thank you for voting!
The refrigerator made a humming/grinding sound
-
Glenroy from Martinsburg, WV
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I used the socket set to remove pannel that allowed me to have access to the evaporator fan. Once the fan and it's container was visible, I removed the entire fan container using the socket set. I took the fan out of the container, removed the damage blade and the damaged fan grommets. I then replace the old blade with the new blade and p
... Read more
ut the fan and the compartment back together. I am not very handy so if I am able to do this, anybody can. Ps. I was very very pleased with the services I received from PartSelect and would encourage others to use them - must admit I was very suspicious at first.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Added a Second Snack Pan
-
WILLIAM from CHESAPEAKE, VA
- Easy
- 15 - 30 mins
-
Nutdriver
My fridge came with only a single snack pan, and since the glass shelves are identical I decided to order the parts needed for installing the second snack pan. The glass shelf is secured in front by a round plastic pin protruding from the side of the fridge. Once the shelf is lifted upward and free of this pin, the rear retaining ears on
... Read more
the metal shelf side brackets can be released from the vertical-slotted metal track at the rear of the fridge. Make certain that you have the Right and Left snack pan slides oriented correctly, and positioned on the correct side of the metal shelf brackets. You’ll need to thread two self-tapping screws into each of the snack pan slides: one near the front, and the other at the rear. These screws extend through the metal side brackets into pre-aligned holes in each pan slide. When this is completed, you can test-fit the new clear plastic pan slide (drawer) into the slides to make sure it fits correctly. All that's left to do is insert the retaining ears into the appropriate pair of slots at the rear, then lower the front of the glass shelf until it's properly positioned over the plastic support pin. Now you're ready to enjoy twice the snack pan capacity as before!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
frosting over and freezer not cold enough and not circulating cold air .
-
Erold from Alamosa, CO
- Really Easy
- 15 - 30 mins
-
Nutdriver
Defrosted the refrigerator,power off and cut the 2 wires on thermostat and sodered the new one on and shrink tube sealed the wires,refrigerator works like new!
Was this helpful?
Thank you for voting!
refig light did not work
-
paul from east hanover, NJ
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
per your instructions
Was this helpful?
Thank you for voting!
frig door kept slamming into cabinet
-
Anthony from Riverview, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took the old stop off put the new stop on
Was this helpful?
Thank you for voting!
replace worn & yellowed door handles
-
Grace from The Villages, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Just unscrewed old handles & screwed in the new one. Very easy. Have a good Phillips head screw driver.
Was this helpful?
Thank you for voting!
light switch quit working
-
David from Simpsonville, SC
- Easy
- Less than 15 mins
-
Screw drivers
removed the inside fridge electrical panel and swapped switches
Was this helpful?
Thank you for voting!
failed light switch
-
Jules from Crowley, LA
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this helpful?
Thank you for voting!
no light in freezer
-
christopher from collegeville, PA
- Really Easy
- Less than 15 mins
Connected the 2 wires and pushed in the switch until it clicked.
Was this helpful?
Thank you for voting!
The Gasket arount the door was coming apart and the door would not close properly.
-
Susan L from Hagerstown, MD
- Really Easy
- Less than 15 mins
I came home to find a mess near the refridgetor. My teenage daughter or son had made themselves a peterbutter and strawberry homemade jam sandwhich. The strawberry jam was all over the inside of the door and on the floor. What a mess, so I was waiting for my husband to change the gasket around the door anyways. So I though to myself I jus
... Read more
t change it myself. The old one just came off and I pulled the new one out of the box and I went right on with not much effort. ( I wiped down the area after I put off the old gasket) Thank you very much for making the parts so easily avaiable on your website without having to buy a new refrigator. Thanks again Sue and Ed
Read less
Was this helpful?
Thank you for voting!
sticky switch
-
ANTHONY from NEW EGYPT, NJ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this helpful?
Thank you for voting!