EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38187 General Electric Refrigerator - Instructions

All Instructions for the 38187
46 - 60 of 125

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer was cold but fridge was warm. Coils in the back of the freezer were getting frosted. Defrost Sensor was broken
1 person found this instruction helpful.
  • Kevin from Charlotte, NC
  • Easy
  • 30 - 60 mins
  • Socket set
-Empty the freezer
-Take the cover in the back of the freezer off
-Melt the ice off the coils (heat gun, hot water, etc.)
-Cut the wires off the old sensor and connect the new sensor using a soldering iron or some other method.
-Cover the spliced wire with heat shrink, electrical tape or some other method.
-Reasse mble the cover

Done!
Was this helpful?
Thank you for voting!
water leaking from under dishwasher
1 person found this instruction helpful.
  • Edward from E LONGMEADOW, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Socket set, Wrench (Adjustable)
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.

Indeed , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.

A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Was this helpful?
Thank you for voting!
Fan was not centered in the middle of the back panel opening.
1 person found this instruction helpful.
  • James from GREENSBORO, NC
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.
Was this helpful?
Thank you for voting!
Loud whirling noises when the motor started up, then they subside (and stop) in a short time
1 person found this instruction helpful.
  • Randy from VALLEY CENTER, CA
  • Very Difficult
  • More than 2 hours
I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one
Was this helpful?
Thank you for voting!
Noisy
1 person found this instruction helpful.
  • Brad from SPRING MILLS, PA
  • Very Difficult
  • More than 2 hours
I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.
Was this helpful?
Thank you for voting!
Loud Sound In Freezer
1 person found this instruction helpful.
  • Carolyn from Santa Ana, CA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I followed the video for my model refrigerator on parts select. My hint: when returning the back panel of the freezer, it's slightly adjustable left and right to avoid grazing the fan.
Was this helpful?
Thank you for voting!
noisy refrigerator
1 person found this instruction helpful.
  • James from NEW YORK, NY
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled al l the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.
Was this helpful?
Thank you for voting!
light switch freezer door
3 of 7 people found this instruction helpful.
  • Sumlorq from Cleveland, OH
  • Really Easy
  • Less than 15 mins
put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil
Was this helpful?
Thank you for voting!
Light went out in refrigerator
1 person found this instruction helpful.
  • Gary from EAST JORDAN, MI
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
Was this helpful?
Thank you for voting!
Light would stay on when door closed
3 of 7 people found this instruction helpful.
  • James from Glendale Heights, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.
Was this helpful?
Thank you for voting!
40 year old refrigerator brittle light switch fell apart
1 person found this instruction helpful.
  • Loren from EL PASO, TX
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP
Was this helpful?
Thank you for voting!
Was not allowing defrost heater to work
1 person found this instruction helpful.
  • Ronnie from MARION, LA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
Unplugged refrigerator Removed the cover in freezer compartment
Removed old thermostat and installed new
Replaced cover and plugged in refrigerator
Was this helpful?
Thank you for voting!
Light Switch Not Working - Needed New Switch
1 person found this instruction helpful.
  • Joe from SUGAR LAND, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch d islodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.
Was this helpful?
Thank you for voting!
Broken light switch
1 person found this instruction helpful.
  • Deborah from BRADLEYVILLE, MO
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!
Was this helpful?
Thank you for voting!
freezer iceing up
1 person found this instruction helpful.
  • tom from WESLEY CHAPEL, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
removed screws holding back plate removed air devise pul slightly out lift straight up and ou remov 2 screws in the fan cage remove ice maker 2 screws and a plug in connector.pull back fram slowly forward angle to the left remove.you'll see condenser in front of you.thermostat is to the right attached to top coil of condenser clips on rem ove.two wires cut close to old thermos and remove install new one make sure back which is plastic faces you.attach wires with wire nut or inline #14 slices.just go in reverse to finish. maakesure you unplug fridge first and of course plug her back in.wait 24 hours for everything to settle down.
Was this helpful?
Thank you for voting!
All Instructions for the 38187
46 - 60 of 125