3644 Kenmore Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake element burned out
1 of 2 people
found this instruction helpful.
-
Cynthia from Pierson, MI
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
My husband (a retired tool & die maker) easily removed the old bake element after first turning off the circuit. He cleaned up the burned salt that we had used to try to put the "fire" out but finally just shut down the circuit. Then just as easily istalled the new element. Thanks to your quick service, we were only without the use of
... Read more
the oven for a day and a half!
Read less
Was this helpful?
Thank you for voting!
New element had blade connectors (male).
1 of 2 people
found this instruction helpful.
-
James from MARIETTA, GA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Drilled small holes in blades to accept existing machine screws from oven wires.
Was this helpful?
Thank you for voting!
Lower bake element burned out.
1 of 2 people
found this instruction helpful.
-
Elaine from Hanover, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
1. Turned off power at the breaker box. Removed oven door from oven, and removed bake racks. Determined replacement element from PartSelect was correct. Inspected new element. Using meter, determined new element was OK via continuity test. Gathered all appropriate tools to do the job.
2. Using 1/4" nut driver, removed two reta ... Read more ining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake
2. Using 1/4" nut driver, removed two reta ... Read more ining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake
Read less
Was this helpful?
Thank you for voting!
Element feet broke off and element was laying against botom of oven.
1 of 2 people
found this instruction helpful.
-
James from Glassboro, NJ
- Really Easy
- Less than 15 mins
-
Nutdriver
Turned off the power at the panel and then simply removed the two hext screws and unplugged the old element. Plugged in the new element and used a nut driver to relpace the two screws.
Was this helpful?
Thank you for voting!
Upper over broil unit burned out
1 of 2 people
found this instruction helpful.
-
tim from fort scott, KS
- Really Easy
- 15 - 30 mins
-
Wrench set
This part is a plug-in unit - two screws off; unplug the old unit; plug in the new unit; two screws on. Very simple.
Was this helpful?
Thank you for voting!
Oven elements were not heating properly.
1 of 2 people
found this instruction helpful.
-
Aaron J. from Bartlett, TN
- Really Easy
- 15 - 30 mins
-
Nutdriver
I had to remove two screws that held these elements in place from back of oven; pull the elements out about three inches to disconnect two wires; connected wires to new elements and
replaced two screws.
A very easy job to perform thanks to right parts from PartSelect.
replaced two screws.
A very easy job to perform thanks to right parts from PartSelect.
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven wouldn't heat bottom
1 of 2 people
found this instruction helpful.
-
Thomas N from Blackfoot, ID
- Really Easy
- Less than 15 mins
-
Nutdriver
.First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and reversed the procedure with the new element very simple.
Was this helpful?
Thank you for voting!
Short circuited/burned out upper bake element
1 of 2 people
found this instruction helpful.
-
William from Centreville, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
This is a simple repair of the PS249249 UPPER BAKE ELEMENT requiring only a 1/4 in nut driver or socket wrench.
1. unplug the old element after removing the two screws holding the element in place.
2. Insert the new element in the electrical receptacle and reinsert the screws to secure the new element.
Make s ... Read more ure not to remove any insulation.
1. unplug the old element after removing the two screws holding the element in place.
2. Insert the new element in the electrical receptacle and reinsert the screws to secure the new element.
Make s ... Read more ure not to remove any insulation.
Read less
Was this helpful?
Thank you for voting!
I researched the part number from partselect.com, ordered it and in less than a week (even in all the snow!) I had my part. Fifteen minutes later, my wife was broiling dinner! I repaired my broiler element without waiting on a repairman and for less than $50.00!
1 of 2 people
found this instruction helpful.
-
Elwood from Allen, MD
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the defective element with the new - all inless than fifteen minutes!
Was this helpful?
Thank you for voting!
Bake element broken
1 of 2 people
found this instruction helpful.
-
Charles from Damascus, MD
- Easy
- Less than 15 mins
-
Wrench (Adjustable)
Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.
I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven ... Read more . I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.
I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.
I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven ... Read more . I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.
I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.
Read less
Was this helpful?
Thank you for voting!
Bake burned out, checked open with an ohm meter
1 of 2 people
found this instruction helpful.
-
Jack from Corinth, MS
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
removed two screws holding the element in place, pulled old element out enough to remove wires that are attached with flag terminals. Installation was in reverse. Turned the oven on and cooked some biscuits. The element that I received from PartSelect was a perfect match.
Was this helpful?
Thank you for voting!
Baking element burned through.
1 of 2 people
found this instruction helpful.
-
James from Seattle, WA
- Easy
- Less than 15 mins
-
Nutdriver
First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."
Disconnecting the two wires and recon ... Read more necting them was a simple operation after I cleaned my pants from the electrical short.
Re attaching the two-screw panes to hold the element in place finished the project.
Disconnecting the two wires and recon ... Read more necting them was a simple operation after I cleaned my pants from the electrical short.
Re attaching the two-screw panes to hold the element in place finished the project.
Read less
Was this helpful?
Thank you for voting!
broken element
1 of 2 people
found this instruction helpful.
-
james from keller, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected new one, put back in place with screws
Was this helpful?
Thank you for voting!
burned out
1 of 2 people
found this instruction helpful.
-
David from Woodbridge, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people
found this instruction helpful.
-
Louis from LEAGUE CITY, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
Easy
Was this helpful?
Thank you for voting!