3644 Kenmore Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake Element on Oven Arced and Split
1 person
found this instruction helpful.
-
Lisa from The Woodlands, TX
- Easy
- Less than 15 mins
-
Socket set
Instead of flipping circuit breaker, we pulled the oven away from the wall and unplugged it. Used socket wrench to loosen screws of bracket holding old element onto the back oven wall, then gently pulled element until connecting wires appeared. Removed the 'clips' attached to the old element prongs and discarded old element. Reattached
... Read more
the 'clips' to new element prongs, then gently pushed prongs into back into oven wall until the bracket was flush with the wall. Used socket wrench to screw and tighten the bracket into place. Plugged in the oven and tested the new element to make sure it worked. The whole process took only a few minutes.....it took longer to clean the oven before installing the new element.
Read less
Was this helpful?
Thank you for voting!
burnrd -out heating elements
1 person
found this instruction helpful.
-
deborah from poughquag, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Turned AC off. Removed bracket screws and pulled out ac connections. Removed old element and reilstalled new element and set AC on.
Was this helpful?
Thank you for voting!
The bake element caught on fire. I needed to replace the burner..
1 person
found this instruction helpful.
-
Sandra from Muskegon, MI
- Really Easy
- Less than 15 mins
-
Socket set
All I had to do was just unscrew the bolts,pull out the old one, and put the new one on its metal clips and then rebolt.So easy and I know I would have had to pay much more then what I did for the part..This place is super.I ordered my part one day, and it was there the next...Sandy
Was this helpful?
Thank you for voting!
baking element arced and burned out
1 person
found this instruction helpful.
-
Norman Levitz from Manchester Center, VT
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to
... Read more
swap out the parts and... success!
Don't forget to turn off the circuit breaker before starting repairs.
Don't forget to turn off the circuit breaker before starting repairs.
Read less
Was this helpful?
Thank you for voting!
a segment of the broil element took on fire
2 of 4 people
found this instruction helpful.
-
maria from great neck, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
it was real easy, I just watched my husband do it!
Was this helpful?
Thank you for voting!
Bake element caught fire and melted
2 of 4 people
found this instruction helpful.
-
Fareed from Randolph, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver
Turn off power at the circuit breaker before working on electric thing.
Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.
Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.
Was this helpful?
Thank you for voting!
Old Terminal Block was arcing.
1 person
found this instruction helpful.
-
Robert from HOUSTON, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Cut Wires to old terminal block and wired in new Terminal Block
Was this helpful?
Thank you for voting!
oven heating element burned out
1 person
found this instruction helpful.
-
Howard from East Orleans, MA
- Easy
- 15 - 30 mins
-
Pliers, Socket set
First turned off the power to the stove at the breaker panel, thenI removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Disconnecting/reconnecting the "clips" was the only difficult part because they did not slip off/on easily. Replaced the element in the ov
... Read more
en, replaced the screws...good to go!
Best part of buying from Parts Select was that they shipped the part the same day I ordered it, which was the Friday after Christmas. Competitor would not have shipped till the following Monday and we needed the oven ASAP!
Best part of buying from Parts Select was that they shipped the part the same day I ordered it, which was the Friday after Christmas. Competitor would not have shipped till the following Monday and we needed the oven ASAP!
Read less
Was this helpful?
Thank you for voting!
RT END CAP THAT WAS BR0KEN
1 person
found this instruction helpful.
-
WILLIAM from ALLENTOWN, PA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
REMOVED 5 PHILLIPS SCREWS
REMOVED BROKEN RT CAP
INSTALLED NEW END CAP
REINSTALLED THE SCREWS
PROJECT COMPLETE
REMOVED BROKEN RT CAP
INSTALLED NEW END CAP
REINSTALLED THE SCREWS
PROJECT COMPLETE
Was this helpful?
Thank you for voting!
Oven would not heat
1 person
found this instruction helpful.
-
Franz from CRESTVIEW, FL
- Very Easy
- Less than 15 mins
-
Nutdriver
Removed old broken element and installed new one. Took less than 10 minutes
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 people
found this instruction helpful.
-
Catherine from SEATTLE, WA
- Very Easy
- Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
element broke
1 person
found this instruction helpful.
-
Art from FRESNO, CA
- Very Easy
- 15 - 30 mins
-
Screw drivers
Fast shipping, Very easy to install I am a senior and had no problems works Great!!
Was this helpful?
Thank you for voting!
element broke
1 person
found this instruction helpful.
-
Richard from NEW BERLIN, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.
Was this helpful?
Thank you for voting!
bake element was fried
1 person
found this instruction helpful.
-
William from MARTIN, GA
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
I went by the video
Was this helpful?
Thank you for voting!
Replace bake heater element
1 person
found this instruction helpful.
-
Douglas from Corvallis, OR
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings
... Read more
. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.
Read less
Was this helpful?
Thank you for voting!