3644 Kenmore Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner wouldn't heat up
3 of 4 people
found this instruction helpful.
-
James from Saratoga Springs, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
pulled out the stove,,unhooked the power cord from outlet. I then pulled the control knob off and removed the the six screws from the back panel. I then removed the two screws the were under the knob and removed switch from panel..I unhooked the wires one at a time and rehooked them to the new switch,,pushed the switch back in the panel a
... Read more
nd installed the two screws. The knob was different from the shaft on the new switch so I took my dremel and contoured the shaft to fit my switch. I plugged the stove back into the outlet and it worked perfect..
Read less
Was this helpful?
Thank you for voting!
Oven element burned out
3 of 4 people
found this instruction helpful.
-
STEVEN from EXTON, PA
- Easy
- 30 - 60 mins
-
Nutdriver
Truned off the power took out the two screws holding the old element disconnect the power leads and put in the new element. Was great to recieve the new element in one day, the day before Xmas.
Was this helpful?
Thank you for voting!
The top (broiler) element melted in two.
2 of 2 people
found this instruction helpful.
-
Kenneth from PLANO, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Socket set
Be sure to flip the breaker to the oven to the OFF position before doing anything. Take out the two screws at the back of the oven that hold the element. Carefully pull the element forewarn to expose the connections to the wires. Disconnect the element from the wiring connectors. Be careful not to damage the connectors or the wiring. Plug
... Read more
the new element into the wiring connectors. Make sure you have the connections firmly in place. Push the wiring and connectors back into place. Replace the two screws. Make sure the element is resting in the spacers that keep it the correct distance from the top of the oven. Flip the breaker to the ON position, Turn the oven on Broil. The element should start turning a bright red. some fumes will come off the element. That is just oil from processing and handling. Your done!
Read less
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people
found this instruction helpful.
-
Gerald from WINTERVILLE, GA
- Very Easy
- Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
Oven top Broiler was broke
2 of 2 people
found this instruction helpful.
-
Alvin from CRYSTAL SPGS, MS
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I pulled the old broiler from holding clamps. I unscrewed the 2 screws holding the old broiler, pulled it out very slowly while using clips to hold the wires from going back into the wall behind the oven. That’s very important, I then pulled the old broiler off and replaced the new one. First I secured the elements on the oven clips that
... Read more
hold the element up, I reattach the new element, screwed the 2 screws back in. DONE My grandson helped, total time, maybe 15 minutes. Watch their video. Really easy, save money.
Read less
Was this helpful?
Thank you for voting!
bake element caught fire and turned to ash in a section
2 of 2 people
found this instruction helpful.
-
Heather from Dearborn, MI
- A Bit Difficult
- 15 - 30 mins
-
Socket set
The entire element was replaced. Since the oven is proably older than me (about 30 years) the holes did not light up exactly so 2 new holes had to be drilled. It is working great now and I'm happy to find a part that works.
Was this helpful?
Thank you for voting!
Element had burned itself out
2 of 2 people
found this instruction helpful.
-
Glen from West Harrison,, NY
- Really Easy
- 15 - 30 mins
-
Wrench (Adjustable)
The repair was remarkably simple. Had i a nut driver, it would have been simpler still. Nonetheless, I managed to remove the nuts affixing the element to the back of the oven with a wrench, pulled out the old element, reattached the wires (they slipped in with ease), replaced the element, tightened the nuts and, presto, I was done. I s
... Read more
uspect I saved over $100, though would rather my wife not know for fear it will be spent elsewhere;-)
Read less
Was this helpful?
Thank you for voting!
element burned out
2 of 2 people
found this instruction helpful.
-
meryl from chester, NJ
- Easy
- 15 - 30 mins
-
Pliers, Socket set
Removed screws holding old element; removed back panel. Attached new element with old screws and replaced panel.
Was this helpful?
Thank you for voting!
bake element burnt into
2 of 3 people
found this instruction helpful.
-
gary from assumption, IL
- Easy
- 15 - 30 mins
-
Nutdriver
repair went fine, real easy.
Was this helpful?
Thank you for voting!
Broil element
2 of 3 people
found this instruction helpful.
-
Maria from Costa Mesa, CA
- Easy
- 15 - 30 mins
-
Socket set
switched off power to oven, unscrewed old broiling unit and installed new one.
Was this helpful?
Thank you for voting!
oven stopped heating and element appeared broken
2 of 3 people
found this instruction helpful.
-
Henry J from South Haven, MI
- Really Easy
- 15 - 30 mins
-
Socket set
The customer service rep was brilliant in finding the
right part number! It was sent the following day
(with email to let me know) The part itself was just
exactly like the old one. I simply turned off the power,
removed the 2 metal screws and unplugged the
broken element. The new one fit properly and works
... Read more />like a million dollars. For about $50, you made me
look like a hero in my own house! Thjank you
right part number! It was sent the following day
(with email to let me know) The part itself was just
exactly like the old one. I simply turned off the power,
removed the 2 metal screws and unplugged the
broken element. The new one fit properly and works
... Read more />like a million dollars. For about $50, you made me
look like a hero in my own house! Thjank you
Read less
Was this helpful?
Thank you for voting!
Burner control was erratic. Sometimes it worked, sometimes it didn't.
2 of 3 people
found this instruction helpful.
-
Charles from Clarksville, OH
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First pull knob off switch. You may need a small screwdriver to gently start it. I then removed two screws, one in each end of control panel. Then rolled the panel up and out, as it is kind of hinged in the back. Removed two screws from switch front,layed it to the side and installed new switch. Removed wires (there were 5) one at a time
... Read more
with needle nose pliers, and placed on new switch. Replaced panel screws and was finished. Easy fix, quick delivery of part, I have used Partselect in the past and will continue.
Read less
Was this helpful?
Thank you for voting!
Inner glass of slide in range was cracked needed replaced
2 of 3 people
found this instruction helpful.
-
Thomas from Westerville, OH
- Easy
- 30 - 60 mins
-
Screw drivers
Removed door from Oven.
removed screws from several components comprising the door and separated pieces.
Removed broken glass.
Prior to putting back together I took advantage of the convenience and used oven cleaner to clean inner portion of door. Installed new glass.
Reassembled door.
removed screws from several components comprising the door and separated pieces.
Removed broken glass.
Prior to putting back together I took advantage of the convenience and used oven cleaner to clean inner portion of door. Installed new glass.
Reassembled door.
Was this helpful?
Thank you for voting!
broiler element broken -- rotted
2 of 3 people
found this instruction helpful.
-
Robert from Alpine, NJ
- Easy
- 1- 2 hours
-
Nutdriver, Pliers
First I removed the two screws that hold the element in place. I then pulled the element out disconnected the two wires. THE PROBLEM IS THAT THERE IS HARDLY ANY WIRE TO WORK WITH. Otherwise I would have been finished in ten minutes.
Was this helpful?
Thank you for voting!
Heat element burned out
1 person
found this instruction helpful.
-
Donna from Thornville, OH
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..
Was this helpful?
Thank you for voting!