3644 Kenmore Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake Element Burned Through A Weak Section Of The Tube.
18 of 19 people
found this instruction helpful.
-
PAUL from CAMDEN, AR
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I removed the two mounting screws then pulled the element forward and disconnected the two element screws. I reversed the process to install the new one/ this oven is over 30yrs old.
Was this helpful?
Thank you for voting!
Replacement of heating element
16 of 16 people
found this instruction helpful.
-
Kimberly from El Cerrito, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
If I'd had the Nut driver, it would have taken 15 -20 minutes or less. Went to Ace Hardware, bought the nut driver for $4.99.
Turn off the power at the box! Turn off the oven as well. Four screws total. Two to hold it in place and two that connect the element to the source.
First I removed the two screws that h ... Read more old the element in place. I pulled the element out about 2 inches. Two more screws connect the element wires. I disconnected the element, threw it away, then connected the new element. I put the element in place, then replaced the screws that connect the power. Finally, I replaced the screws that hold the element in place.
Kimberly, El Cerrito, California
Turn off the power at the box! Turn off the oven as well. Four screws total. Two to hold it in place and two that connect the element to the source.
First I removed the two screws that h ... Read more old the element in place. I pulled the element out about 2 inches. Two more screws connect the element wires. I disconnected the element, threw it away, then connected the new element. I put the element in place, then replaced the screws that connect the power. Finally, I replaced the screws that hold the element in place.
Kimberly, El Cerrito, California
Read less
Was this helpful?
Thank you for voting!
Oven stops heating and states F3 error code.
19 of 26 people
found this instruction helpful.
-
Arno from Sacramento, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
The most obbious suspect is the upper oven fan. Turned off power circuit breaker. Removed two philip screws at top of control panel and lowered the panel. Using the 3D view of the oven on this web site I located the fan limit switch. Jumpered the limit switch. Turned power on and the fan ran. That proved the switch was defective and
... Read more
not the fan. Replaced the limit I purchased from Partselect.com.
Please note* My life career was electrical. I used the schematic that came with the oven to determine that the limit was the only control between one of the 240 volt lines and the fan. Thus I knew it was safe to jump the limit.
If you are in doubt, seek some advice.
Good Luck, Arno
Please note* My life career was electrical. I used the schematic that came with the oven to determine that the limit was the only control between one of the 240 volt lines and the fan. Thus I knew it was safe to jump the limit.
If you are in doubt, seek some advice.
Good Luck, Arno
Read less
Was this helpful?
Thank you for voting!
uncontrollable heat - would not cycle off
17 of 21 people
found this instruction helpful.
-
anthony from maumelle, AR
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Turn circuit breaker off.Raise up cook top and remove 6 screws that hold catch pan in place.move 3 screws that hold switch cover panel [2 sections]in place. Pull off knob for bad switch and remove 2 screws.Pull off each of the 5 wire terminal clips by removing one at a time and replacing that one on the new switch control to assure correc
... Read more
t placement.Reinstall switch cover panel and catch pan.
Read less
Was this helpful?
Thank you for voting!
Baking element broke in half
12 of 12 people
found this instruction helpful.
-
Nancy from West Harrison, IN
- Really Easy
- Less than 15 mins
-
Wrench set
I removed the screws holding the old element in place, then pulled it out a few inches from the back oven wall. Then I pulled the wires away from the old baking element (pulled off easily), and being careful to keep the wires on the same sides as before, pushed the new element on to the wires. It was then just a matter of inserting the
... Read more
wires and insulation back into the opening and tightening the screws. Simple!
Read less
Was this helpful?
Thank you for voting!
Lower Heating Element Out
12 of 13 people
found this instruction helpful.
-
Steve from Clarksville, OH
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) discovering a burnt spot in the element sent me searching for a new one. I couldn't find any locally, so I continued my search to the internet. This is when I came in contact with PartsSelect.com .
... Read more
They made identifing the part and ordering so easy it was unbelievable. Super fast deliverey astounded me as well. The installation of the new element was reverse of the old. All of the dimensions and info for the part were right there on this site. Thanks
They made identifing the part and ordering so easy it was unbelievable. Super fast deliverey astounded me as well. The installation of the new element was reverse of the old. All of the dimensions and info for the part were right there on this site. Thanks
Read less
Was this helpful?
Thank you for voting!
Broiler element would not heat; bake element did heat
12 of 14 people
found this instruction helpful.
-
Brad from San Carlos, CA
- Easy
- 15 - 30 mins
-
Socket set
Removed the oven racks, removed screws holding element hanging support from roof of oven, removed screws holding plate of element to rear of oven. CAREFULLY worked element loose from back of oven and gently alternated pulling each side of element (near the base) until connecting wires came free of insulating batting. Pull too hard and t
... Read more
he connecting wires can break loose and disappear behind the batting. Once freed, disconnected both wires with socket (use pliers for extra grip on flat part of connectors, if necessary), removed element, braced new element on bottom of oven, aligning connectors to now-free wires. Re-attached with the new screws that came with the element (attachment points on element are threaded; do not reuse old screws as the threads may not match), gently re-inserted element into insulating batting at rear of oven, reattached hanging support, then replaced element plate screws.
Can be difficult to work in small, deep ovens....many oven doors can be removed. If so, remove oven door and use a chair as a support...lie on your back on the chair and hang your head and arms in the oven.
Can be difficult to work in small, deep ovens....many oven doors can be removed. If so, remove oven door and use a chair as a support...lie on your back on the chair and hang your head and arms in the oven.
Read less
Was this helpful?
Thank you for voting!
Oven would not preheat - took over 1 hr to get to 350 degrees
11 of 12 people
found this instruction helpful.
-
Tim from Mt Juliet, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
Turned the range/oven off at the breaker box. Pulled all the racks out. Unscrewed two screws holding lower heating element in. Pulled the heating element out to expose connections. Unhooked connections, plugged in new element. Replaced the screws. Turned breaker back one. Pretty simple!
Was this helpful?
Thank you for voting!
Interior light needed replaced
22 of 46 people
found this instruction helpful.
-
Leo from TWIN FALLS, ID
- Really Easy
- Less than 15 mins
-
Nutdriver
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Was this helpful?
Thank you for voting!
Broken oven element.
10 of 11 people
found this instruction helpful.
-
NICHOLAS from BALTIMORE, MD
- Really Easy
- Less than 15 mins
-
Nutdriver
DO NOT ATTEMPT THIS REPAIR UNTIL THE RANGE IS UNPLUGGED AND THE CIRCUIT BREAKER IS OFF!!!!!!
Very easy repair, but, either there is a minor amount of current flowing through the element at all times, or the off switch wasn't working when I started. didn't turn the breaker off, after I removed the nuts, as I was pulling the ele ... Read more ment to reveal the terminals, the terminals arc'd on the oven wall. BIG SPARKS!
After I turned the breaker off and started again. No problems.
Very easy repair, but, either there is a minor amount of current flowing through the element at all times, or the off switch wasn't working when I started. didn't turn the breaker off, after I removed the nuts, as I was pulling the ele ... Read more ment to reveal the terminals, the terminals arc'd on the oven wall. BIG SPARKS!
After I turned the breaker off and started again. No problems.
Read less
Was this helpful?
Thank you for voting!
Daughter broke outer glass on stove
8 of 8 people
found this instruction helpful.
-
Pat from Rudyard, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Unpacked the glass, unscrewed the screws, slid the glass in and screwed the screws again.
Was this helpful?
Thank you for voting!
the bottom baking element broke on my upper oven... cracken in half
9 of 11 people
found this instruction helpful.
-
Kathy from Naperville, IL
- Easy
- Less than 15 mins
-
Pliers, Wrench set
It was very simple.. first turn off the electricity... next take out the two screws holding the element to the back of the oven... then pull the two plugs apart( male and female ends) ... throw away old part.
put new part in by plugging the male and female ends back together... push back into oven back.. get all insulation back in... ... Read more put two old screws back in to secure... done.. turn on power...
don't be afraid.. it was very, very easy.
put new part in by plugging the male and female ends back together... push back into oven back.. get all insulation back in... ... Read more put two old screws back in to secure... done.. turn on power...
don't be afraid.. it was very, very easy.
Read less
Was this helpful?
Thank you for voting!
Twice I ordered the oven light bulb & each time the light bulb was defected
18 of 38 people
found this instruction helpful.
-
Barbara from BELLEVUE, WA
- Very Difficult
- Less than 15 mins
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl
... Read more
iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Read less
Was this helpful?
Thank you for voting!
The Bake Element Split
8 of 9 people
found this instruction helpful.
-
Steve from Surprise, AZ
- Really Easy
- Less than 15 mins
-
Pliers, Socket set
This was so easy I should be a repairman! Turned off power at the breaker, used socket to unscrew two hex head screws, pulled out element slowly from the back of oven wall - enough to expose the wires about 3". Used pliers to remove clips from terminals, put new element in, pushed on new terminal clips, fed wires and terminals back throug
... Read more
h the two holes, replaced the hex head screws, turned breaker on and wallah! My wife was happy! That's a good thing.
Read less
Was this helpful?
Thank you for voting!
Bake element did not get hot.
8 of 9 people
found this instruction helpful.
-
Jeanette from Vergennes, VT
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench set
I was able to remove the heating element but in the process one of the wires fell behind the back wall of the oven so I needed a little help getting it out. It was my first time working with electricity. If this didn't happen the repair would have been quit easy. The instructions were great.
Was this helpful?
Thank you for voting!