EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3644 Kenmore Range - Instructions

All Instructions for the 3644
31 - 45 of 367

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lower element burned out
7 of 7 people found this instruction helpful.
  • John from Germantown, WI
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Remove the screws inside the oven holding the back of the element to the rear wall of the oven. These scrrews are a square drive. Pull element forward and remove 2 screws that hold wires in place. Both sets of screws needed to be replaced with a different size. Reverse order to install.
Was this helpful?
Thank you for voting!
Oven bake element blew out
6 of 6 people found this instruction helpful.
  • Michael from Indianapolis, IN
  • Really Easy
  • Less than 15 mins
  • Pliers
Shut off the power from the fuse box. Removed p the two screws and plate that attach the element to the wires and back of oven. Installed the replacement element by attaching the wires and reinserting the two screws. Restored power and tested the new element by preheating the oven at 350 degrees and letting it heat for 15 minutes. Works like a charm!
Was this helpful?
Thank you for voting!
26 year old oven, lower element burned into two pieces.
6 of 6 people found this instruction helpful.
  • marsha from oklahoma city, OK
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
I first removed the broken element by removing the two hexhead screws on either side of the element bracket. Then I gently pulled the wires through the opening and removed two more screws that attached the wiring to the element. I then compared the new and old elements and found a few differences.

First, the screw holes whe re the wires connect to the element were tiny in the new element, about a third the size of the holes in the old one. Secondly, the mounting bracket was not as long as the original, and the holes to mount it to the back of the oven are located at the top of the bracket, instead of the sides.

Since this was the only element that I have found, that comes close to the original, I decided to make it work.

I took my drill and a small bit and bored out the screw holes, just enough to get a self taping screw to fit and reconnected the wires.

Now I'm not sure that I would recomment the next step to anyone, but I did this: I held the new bracket against the back of the oven and drilled new holes to match the new bracket, and again used self tapping screws. The reason that I don't encourage this is that the new bracket fits just inside of the old opening, but the insulation cannot be seen as long as the element does not get moved. I then plugged the original bracket holes with the original hex head screws.

It took a little more time and effort than I had expected, but well worth it, after eight months without the use of my oven.
Was this helpful?
Thank you for voting!
Bottom element burnt out
6 of 7 people found this instruction helpful.
  • Curtis from Oxon Hill, MD
  • Easy
  • Less than 15 mins
  • Screw drivers
remove two screws slide out. slide new one in. put two screws back. done.
Was this helpful?
Thank you for voting!
element burned out
6 of 7 people found this instruction helpful.
  • John from Durham, NC
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
It's so simple most people could mannage the repair. Turn oven off. Remove oven door and shelves. Use a nut driver to remove mounting screws. Pliers to pull quick connect terminated wires off element terminals. Use pliers to push connectors onto new element,wires may connect to either terminal. Nut driver for screws to mechanically mount new element. Replace shelves and door. First time element gets hot it will burn off oils and dirt, not a problem but do it now not later.
Was this helpful?
Thank you for voting!
my lower oven heater went out
6 of 7 people found this instruction helpful.
  • lorita from bend, OR
  • Really Easy
  • Less than 15 mins
  • Nutdriver
i was really pleased getting the order from partselect. i had torn my oven appart and knew i needed just this one part i came home and ordered it from parts select and actually got the part the next day.... very nice.... so pleased
Was this helpful?
Thank you for voting!
Replace the heating coil in convection oven
5 of 6 people found this instruction helpful.
  • Victoria from San Jose, CA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
[1] squirted LiquidWrench on the 4 screws holding the convection fanblade rear cover in place. Used a socket and rachet to remove screws; the loosener really helped after 10+ years.

[2] the broken heating element was easy to remove. The two spade connectors however didn't have much free length;these wires wanted to retreat back into the rear oven wall.
[3] So i put a small binder clip from my desk supplies on each spade end, this left the connectors where I could grab them.
[4]I used needle-nose pliers to firmly crimp the the spade connectors onto the new heating element; couldn't have made a firm placement with fingertip pressure alone.
[5] I cleaned the oven door hinge area, oven bulb area, and other hard to reach spots with Simple Green and wipes.
Was this helpful?
Thank you for voting!
TOP OVEN BROILER ELEMENT BURNED OUT & BROKE
5 of 6 people found this instruction helpful.
  • HIDDEN HILLS from TONASKET, WA
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Pliers
1) TURNED OFF THE POWER TO THE OVEN. 2) REMOVED THE TOP DOOR AND RACKS. 3) REMOVED THE 2- 1/4 HEAD HEX NUTS AND PULLED THE ELEMENT FORWARD ENOUGH TO EXPOSE THE ELECTRICAL CLIPS TO THE ELEMENT. REMOVED THE CLIPS WITH A PAIR OF NEEDLE NOSE AS ADDED GRIP. 4) PUT THE WIRE CLIPS ON THE NEW ELEMENT A ND REVERSED THE ABOVE PROCEDURES.
Was this helpful?
Thank you for voting!
Baking element quit
4 of 4 people found this instruction helpful.
  • Richard from Laguna Niguel, CA
  • Very Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Socket set, Wrench (Adjustable), Wrench set
Removed burned out element and discovered replacement element had a different back plate and different hole pattern. Also, the electical connecttion from power wires to ends of element were a TOTALLY different size, both in hole size and size of material that hole was placed. This tood a lot of slow increasing the size of the hole time. Also, the backplate was a different size with a two hole pattern at the top of the plate, as oppossed to the original plate with holes centered at the sides of the plate. Had to drill holes in back oven wall higher than I wanted, as the oven wall had a depression in the back wall and I could not drill at that point. By drilling holes that were higher than previous holes, there was now a 1/2" opening at the bottom of this plate. Used a hack saw and cut off a piece of the old plate to slip underneath, then screwed in the new plate, thus filling the remaining opening, and securing the additional hand made additional plate. This was a lot more than I had bargain for, and when I turned on the oven, it did not work! I re-checked the connection of the power wires to the grid element and found one of the connections to be disconnected. Reconnected this wire and everything is just ducky now.
Was this helpful?
Thank you for voting!
Large burner didn't work
4 of 5 people found this instruction helpful.
  • Mell from San Antonio, TX
  • Easy
  • 1- 2 hours
  • Screw drivers
Switching out the part was reasonably easy. The hard part twas that over 15 years some of the other parts have dried out. The oven indicator light came loose and the tabs on the clock were broken. With the help of some glue & some Z bracket it is back together minus the oven indicator light. Not perfect but cheaper than buying a new one.
Was this helpful?
Thank you for voting!
Heating element had shorted out and broken.
4 of 5 people found this instruction helpful.
  • Lisa from Lexington, KY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Unscrewed the heating element from the inside back of the oven and removed the housing cover from the back of the stove to access the terminals. (The unit had arked and fused the terminal to the connector.) Installed the new unit and replaced the housing cover on the back and screwed the unit into the back of the oven. Works like a charm .
Was this helpful?
Thank you for voting!
Element control stopped working
4 of 5 people found this instruction helpful.
  • Robert from Covesville, VA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First I unplugged the stove. I then removed the control panel using a flat head screw driver. Then I removed the two screws (phillips head) holding the element in. Five wires had to be disconnected from the old element and placed on the new one. As I removed each wire from the burned out element, I placed it in the same place on the n ew one. I then replacedd the element on the stove and put the control panel back in placed. I plugged the stove into the wall outlet and tested the element control. This whole procedure took no longer than about fifteen minutes.
Was this helpful?
Thank you for voting!
unit burnt out no broiler
7 of 14 people found this instruction helpful.
  • Becky from Piedmont, MO
  • Really Easy
  • Less than 15 mins
  • Nutdriver
took old unit and measured it part select made it easy for me ordered new unit and installed easily and quick thanks to quick service and shipping
Was this helpful?
Thank you for voting!
Bad element
3 of 3 people found this instruction helpful.
  • Ed from Talladega, AL
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers
Removed mounting screws and element only pulled out about 2 inches. Disconnected wires and had to drill slightly bigger hole in element ends to reattach wires. Element mounting bracket was different than old element. Had to use one existing screw hole in oven back and drill a new one.
Was this helpful?
Thank you for voting!
Lower heating element cracked
3 of 3 people found this instruction helpful.
  • Craig from Dayton, OH
  • Very Easy
  • Less than 15 mins
  • Pliers, Socket set
Followed the video directions on your website - GREAT INFORMATION. Everything went very smoothly It took me longer to find my work light (after turning off the electric to the oven) out in the garage than it did to complete the repair!! SUPER PLEASED - WOULD NOT HESITATE TO RECOMMEND THIS COMPANY TO ANY DIY ADVENTURER!!
Was this helpful?
Thank you for voting!
All Instructions for the 3644
31 - 45 of 367