EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3644 Kenmore Range - Instructions

All Instructions for the 3644
121 - 135 of 367

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broiler element blew out.
2 of 5 people found this instruction helpful.
  • Gilbert from Clarkston, MI
  • Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
- removed the old element
- looked for part number, was none
- could not find direct replacement listed
- compared to dimensions on drawing
- ordered part
- discovered that the mounting plate on new element was too small, holes did not line up, did not cover opening in back of oven.
- sawed off mounting plate on new element
- removed mounting plate from old element
-drilled out holes on old mounting plate to accept new element
- attached the modified element
- Everything works fine.
Was this helpful?
Thank you for voting!
The oven heating element broke in two.
1 of 3 people found this instruction helpful.
  • Anna from Texas City, TX
  • Really Easy
  • Less than 15 mins
  • Socket set
Rating: 5 Stars!! We cut the power, removed two screws disconnected the two wires (just pulled them out of the covers) from the old element and pushed in the new ones. It didn't take longer than 10 minutes!

This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices !
Thank you,
Was this helpful?
Thank you for voting!
Lower bake element shorted out.
1 of 3 people found this instruction helpful.
  • Val Ray from Idaho Falls, ID
  • Really Easy
  • Less than 15 mins
  • Nutdriver
1st, Turn off the stove at the electrical box. 2nd, Remove the oven door by opening it to the first stop, and then pulled it straight up. 3rd, Remove the 2 screws using a 1/4" nut driver. 4th Pull the old heating element straight out, until the two wires that attach to the element are out 3" from rear oven wall. (Note: Place a peace o f tape around each wire before disconnecting from the element. this will keep the wires from falling back through the holes). Remove the wires from the old element and remove the old element. 4th Place the new element into the oven, place the wires onto the new element. Then reverse the order of removal for new element install, for the repair. Less than 10 minutes.
Was this helpful?
Thank you for voting!
Element burned out.
1 of 3 people found this instruction helpful.
  • Harden from Lynchburg, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
I spent half an hour finding my driver set. It took about 25 minutes to turn the power off, remove the racks and element and replace the new elements.
Was this helpful?
Thank you for voting!
Bake element broke
0 of 1 people found this instruction helpful.
  • Laura from Telluride, CO
  • Easy
  • 15 - 30 mins
  • Socket set
Removed the two screws and pulled out the bake element. Then plugged in the new element and replaced the screw. Easy
Was this helpful?
Thank you for voting!
A simple repair and a bit of advice...
0 of 1 people found this instruction helpful.
  • John from Virden, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
I really like my repairman, but prefer to do it myself. PartSelect rocks...reasonable prices, really fast shipping AND online repair videos keep me coming back. The repair was exactly as the video described, but one of the wires came loose as I was pulling the element through. I thought I'd have to tear the stove apart to get to it, but luckily, all of the wiring is contained in a raceway that runs along the back of the stove. After removing it to expose the wires, I would recommend doing so instead of trying to pull the wires through as the video shows. In doing so, the terminal connections are readily accessible and it's much easier to remove and install the bake element without having to worry about feeding the wires through at the same time and running the risk of damaging them. Overall, a very simple, quick repair that saved me a $50-75 service call.
Was this helpful?
Thank you for voting!
oven would not heat on bake
0 of 1 people found this instruction helpful.
  • Larry from Burnsville, NC
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The hardest part of repair was moving the oven from the cabnets to unplug and gain access to rear of oven. Remove rear cover panel unplug two spade connectors attached to the heating element. Open oven door and remove the two screws holding the heating element to back of oven. Pull heating element out. Then slide the new element in an d assemble in reverse order.
Was this helpful?
Thank you for voting!
Heating element in bottom oven burned out
0 of 1 people found this instruction helpful.
  • Jim from Arvada, CO
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
First I made sure I turned off the breakers in the circuit box that controlled the circuits for the ovens . Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The factory wrapped a large amount of tape around the connection between the wires and the he ating element. That took a while to get off. And I searched for heat-resistant electric tape to replace it (because, it must have served some purpose if they had it on originally). The wires hooked onto the spade connectors for the new elements with no problem. I pushed them back into the hole in the back of the oven, replaced the screws, turned the breakers back on, and it worked great from there on.
Was this helpful?
Thank you for voting!
Bake Element Burned Out After 25 Yrs
0 of 1 people found this instruction helpful.
  • LEONARD from LAKE ZURICH, IL
  • Easy
  • 15 - 30 mins
  • Socket set
It was easy except that I had to make just a small modification to the electrical connection (holes were to small). . . . Other than that, its was a breeze to install.
Was this helpful?
Thank you for voting!
Burned out heating element
0 of 1 people found this instruction helpful.
  • bonnie from apex, NC
  • A Bit Difficult
  • 15 - 30 mins
  • Wrench (Adjustable)
I had to struggle to get the pliers to grab hold of the screw because they were so tight. I was worried about "stripping the screws" but finally they loosened and I got them both out. My friend was holding the flashlight, so that helped. I was not real sure what to do next but the wires popped off the element so it was clear that all I ha d to do was pop the new one on. Easy. I had the most trouble trying to get the screws out. I saved myself $$$. Thanks for your help in sending the correct part!
Was this helpful?
Thank you for voting!
oven wouldn't heat
0 of 1 people found this instruction helpful.
  • katie from jacksonville, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers
I read the "easy to repair" story after I ordered my part and I felt like I coud do this on my own. (Female not much experience in repairs) I shut off circuit breaker...proceeded to take out element...could not get it to easiler come off...so I made the mistake of cutting the wire because it looked like that's what I needed to do. WORD TO THE WISE...there are clamps that actually pull off the element..just need to pull a little. So my "easy" project was made more difficult because I didn't know this up front. Otherwise it would have been a breeze. I had to go to the hardware store and but new clamps and attach to the cut wire. Good news is my oven is now working and Parts.com was fast, cheaper than the GE parts place and great service.
Was this helpful?
Thank you for voting!
bake element burned out
0 of 1 people found this instruction helpful.
  • Dean from Rolla, MO
  • Easy
  • 15 - 30 mins
  • Nutdriver
I turned the power off.Pushed on the terminals,and used a nut driver to secure the element to the oven back wall.Great service.I recieved the part in 24 hours with reg. shipping at a great price,Unbelieveable!!!
Was this helpful?
Thank you for voting!
the burn element on the bottom burned out
0 of 1 people found this instruction helpful.
  • DEMETRA from MEMPHIS, TN
  • Easy
  • 15 - 30 mins
  • Pliers, Wrench (Adjustable)
first i unplugged the stove to disconnect all power. next itried using pliers to unscrew the screws and was having a hard time so hubby got the adjustable wrench and it was much easier. after taking out the two screws, i pulled the element out about three inches and disconnected the element from the two wires that hold it in place. then i snapped the new element in place just as the old one was and reattached the element to the stove using the two screws. after assuring that element was secure, i turned my oven on to 300 degrees and voila!!! we're cookin again!!!
Was this helpful?
Thank you for voting!
Broken baking (not broiling) element
0 of 1 people found this instruction helpful.
  • Sean from Gettysburg, PA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I shut off the power at the circuit breaker. I loosened the screws securing the baking element to the back wall. I then pulled out the baking element toward me and found the wire leads bolted using self-tapping screws to the original element. Since the holes on the mounting tabs did not take the old screws, I had to drill out the holes on the tabs of the replacement element. After securely bolting the leads to either terminal on the element, I had to drill two holes on the back wall for the mounting plate of the new element. Then I used the cordless drill with the Philips bit to drive in stainless steel self-tapping screws (not zip screws) to secure the element to the back wall. I turned on the power at the circuit breaker and reset the clock (mechanical).
Was this helpful?
Thank you for voting!
Replaced bake element
0 of 1 people found this instruction helpful.
  • Thore from Virginia Beach, VA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Needed to drill two new holes for fastening the element to the oven wall. Change in design. Enlarged the holes in the spade connections since I was unable to find smaller bolts than 4-40.
I would suggest to make the holes in the spade connections larger.
The change out was not a problem.
Was this helpful?
Thank you for voting!
All Instructions for the 3644
121 - 135 of 367