3641 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice in freezer running down sides
8 of 9 people
found this instruction helpful.
-
P. Michael from Tustin, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
This is a built-in unit. Remove the external bezel at the top of the unit. Reach through the unit and unplug the frig. On the compressor unit, you'll see a vertical metal panel. Remove the metal panel and the timer is right behind it. Remove one wire at a time and switch it to the new timer. Remove timer and replace with new one.
... Read more />
Just an added comment, GE Service wanted to put an "ice kit" into my unit. The full repairs would have cost $1,000. While I described how to replace the defrost timer, the problem was the tray heater. But that's another story.
... Read more />
Just an added comment, GE Service wanted to put an "ice kit" into my unit. The full repairs would have cost $1,000. While I described how to replace the defrost timer, the problem was the tray heater. But that's another story.
Read less
Was this helpful?
Thank you for voting!
defrost system kept freezing up
8 of 10 people
found this instruction helpful.
-
Robert from Williamstown, NY
- Easy
- 15 - 30 mins
-
Screw drivers
took out 4 screws - lowered timer cover - replaced timer- put it back together
Was this helpful?
Thank you for voting!
Freezer not getting cold enough to freeze ice cream
8 of 10 people
found this instruction helpful.
-
Gary from ROSETO, PA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
Read less
Was this helpful?
Thank you for voting!
Fan noise
7 of 7 people
found this instruction helpful.
-
Robert from GALVESTON, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed freezer cover, removed fan and fan motor, and bracket holding the fan moter. Installed fan, installed motor and wa-laugh, done.
Other Parts Used:
Was this helpful?
Thank you for voting!
Freezer stopped working
9 of 13 people
found this instruction helpful.
-
Clifford from Melbourne, FL
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
I noticed that if I unplugged the refrigerator and plugged it back in a while later it would start working but eventually would stop. I deduced the problem was likely the defrost thermostat. I ordered the thermostat but it was in a difficult place behind the evaporator coil which I could not remove. While I was trying to work it into posi
... Read more
tion my hand pressed against the defrost coil and shattered the glass sheath. I ordered the coil and finally managed to get it and the thermostat installed. The refrigerator seems to work fine now.
Read less
Was this helpful?
Thank you for voting!
Poor cooling, running all the time
12 of 22 people
found this instruction helpful.
-
MICHAEL from ALEXANDRIA, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed two screws holding the cover. Unclipped and unplugged the defroster timer. Plugged in the new one . Replaced the cover. Finished.
Was this helpful?
Thank you for voting!
Evaporating fan not working
7 of 8 people
found this instruction helpful.
-
flor from glen cove, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I did folllow the instructions on the video step by step.
Other Parts Used:
Was this helpful?
Thank you for voting!
Refridgerator wouldn't cycle into defrost mode without doing it manually.
9 of 14 people
found this instruction helpful.
-
Ben from Warrior, AL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I removed the shield over the timer and the part that supported the timer. Just unpluged it and pluged in new timer and put back shield. I had already replaced the defrost heaters which had totally burned up. I also replaced the thermostat while I was making the repairs although the old one was still o.k. All the information that I needed
... Read more
to make the repairs I obtained through your website. After looking at several websites to compare prices-etc, I found yours to be the best overall. Thanks-a-million your website is worth it's weight in Cold Food !
Read less
Was this helpful?
Thank you for voting!
compressor not starting
9 of 15 people
found this instruction helpful.
-
H.K. from Seagoville, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Refrigerator is not cooling. Light and fan working. Changed the capacitor.. Still not cooling. Back to discovery mode.It may be the timer
Certainly not PartSelect's fault. They have great service.
Certainly not PartSelect's fault. They have great service.
Was this helpful?
Thank you for voting!
Bottom door hinge was lost during move
10 of 18 people
found this instruction helpful.
-
Dustin from Marlow, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
I had lost the bottom hinge during a move and so I rigged the hinge using an old tv antenna and the door never really quite worked right and it was VERY annoying. I stumbled upon this site and was surprised how inexpensive the part I needed was. I was very impressed with the speed of shipping and the install took maybe 5 minutes. The f
... Read more
ridge works as good as new. Thanks a ton!
Read less
Was this helpful?
Thank you for voting!
evap.motor burned out
7 of 9 people
found this instruction helpful.
-
gerald from ardmore, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
common sense,removed plate,removed mounting bracked,unplugged,reversed order,and that was it.
Other Parts Used:
Was this helpful?
Thank you for voting!
refrigerator wasn't cooling but the freezer was working properly
6 of 6 people
found this instruction helpful.
-
Don from BELLVILLE, TX
- Very Easy
- 15 - 30 mins
-
Nutdriver
From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then
... Read more
another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.
Read less
Was this helpful?
Thank you for voting!
Fan Motor was Noisy
6 of 7 people
found this instruction helpful.
-
albert from patterson, NY
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench set
4 screws in the freezer and the back panel came off then 2 more screws to take the motor off. I unpluged the old motor pluged in the new motor put the back panel back on and I was done.
Other Parts Used:
Was this helpful?
Thank you for voting!
Bar end cap broke
6 of 7 people
found this instruction helpful.
-
Bushnell from Gulf Shores, AL
- Really Easy
- Less than 15 mins
Easy fix - snapped together.
Was this helpful?
Thank you for voting!
door dairy was broken
8 of 14 people
found this instruction helpful.
-
Richard from Millbrae, CA
- Really Easy
- Less than 15 mins
Repair was a no brainer. More important, Part Select was extremely efficient. Customer Service was very helpful as my model number was not available on line. Thanks for your wonderful and prompt service. Rich L.
Was this helpful?
Thank you for voting!