3641 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice built up on coils. Fridge was warm.
21 of 24 people
found this instruction helpful.
-
Neil from Boise, ID
- Difficult
- 1- 2 hours
-
Nutdriver, Pliers
No instructions came with new parts. Access to element was impossible until I accidentally discovered that the two styrofoam cushions at the ends of the coils were removable. Once removed, access to the heater and thermostat was very easy.
Unplug appliance, remove freezer shelf, cold air ducts, back of freezer, disconnect lig ... Read more ht, (My model does not have ice maker. This may also need to be disconnected.)
1.Remove styrofoam cushions at end of coils
2.Locate element between bottom two coils
3.Disconnect the male/female connections
4.Remove support clip under center of element
5.Remove element
6.Replace new element in reverse
Connecting the thermostat wires was challenging because they were somewhat behind the coils.
1.With styrofoam removed, unclip thermostat from coil
2.Carefully cut wires (leave enough to connect new wires)
3.Connect new thermostat wires (color of wires matched on my fridge)
4.Clip new thermostat in place
5.Replace styrofoam
6.Button it all up
With these steps, this job would take maybe 30 minutes; somewhat longer if your model has an icemaker.
Hope this helps.
Unplug appliance, remove freezer shelf, cold air ducts, back of freezer, disconnect lig ... Read more ht, (My model does not have ice maker. This may also need to be disconnected.)
1.Remove styrofoam cushions at end of coils
2.Locate element between bottom two coils
3.Disconnect the male/female connections
4.Remove support clip under center of element
5.Remove element
6.Replace new element in reverse
Connecting the thermostat wires was challenging because they were somewhat behind the coils.
1.With styrofoam removed, unclip thermostat from coil
2.Carefully cut wires (leave enough to connect new wires)
3.Connect new thermostat wires (color of wires matched on my fridge)
4.Clip new thermostat in place
5.Replace styrofoam
6.Button it all up
With these steps, this job would take maybe 30 minutes; somewhat longer if your model has an icemaker.
Hope this helps.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
it quit working-refer-freezer-part,fan keeped running
21 of 25 people
found this instruction helpful.
-
jim from buckeye, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver
pulled out switchs verified part #'s-ordered replacements- its actually plug in switches and very simple
Other Parts Used:
Was this helpful?
Thank you for voting!
The Crisper Glass Shelf Broke
23 of 31 people
found this instruction helpful.
-
Marci from Cedar City, UT
- Really Easy
- Less than 15 mins
The Crisper Glass Shelf Broke. My son removed it to clean and dropped the shelf. I ordered a replacement shelf which arrived in record time and just slid it into place.
Was this helpful?
Thank you for voting!
Loud freezer fan motor
21 of 25 people
found this instruction helpful.
-
William from GENEVA, OH
- Very Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed old worn out freezer fan motor and replaced with a new one. Piece of cake. Sooo easy and saved money too!
Other Parts Used:
Was this helpful?
Thank you for voting!
Refrigerator door handle broke
21 of 26 people
found this instruction helpful.
-
Barbara from Philadelphia, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Simply removed the screws and pulled the old handle off and aligned the new handle with the holes and replaced the two screws.
Was this helpful?
Thank you for voting!
The refrigirator light would not come on.
26 of 44 people
found this instruction helpful.
-
Jania from Novato, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Poped out with screwdriver the old swithch and unplugged the two wires. Plugged in the wires to the new swithch and pushed it back in the hole where the old switch was before.
Was this helpful?
Thank you for voting!
the little plastic thingy's were broken
17 of 19 people
found this instruction helpful.
-
rose from cleveland, OH
- Really Easy
- Less than 15 mins
I took the broken part off the bar, put the new part on the bar, snapped it into the fridge, threw the old part out, opened the fridge admired my work, while I was ther I grabbed a beer....couldnt have gone better.
Other Parts Used:
Was this helpful?
Thank you for voting!
The drawers and shelf in my refrigerator broke
21 of 31 people
found this instruction helpful.
-
ROSANNE from HAZLE TOWNSHIP, PA
- Really Easy
- Less than 15 mins
I ordered new ones The came really fast. One was broken . My exchange was handled with great speed and excellent customer care.
Other Parts Used:
Was this helpful?
Thank you for voting!
Refrigerator fan motor died
16 of 18 people
found this instruction helpful.
-
Kevin A. from CONCORD, NH
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Socket set
It has been my experience that these motors sometimes die when the refrigerator is overfilled and motor strains to keep refrigerator cold. And this motor is used in several models of refrigerators. That said, sometimes the hook-up is slightly different between other units. The available video is good, but like I said, circumstances wil
... Read more
l be slightly different between various models.
After cleaning out freezer (plug disconnected first), start to remove outer plastic covers. If you want to keep track of the different steps, you can take pictures with your cellphone. And if there are any connecting wire attachments you think you might not remember, again, you can take a picture, or label with tape (colored tape, or by writing on the tape). And for keeping track of the different-size screws, I place them in a muffin tin, keeping an order of left to right and top to bottom in the tin. When removing Styrofoam blocks in bottom center, make sure you remove any remaining ice underneath in the hole so refrigerator can "breathe". Freezer air is moved below to refrigerator compartment, so a blocked vent hole will strain refrigerator as it tries to maintain its temperature setting and can be the cause of your failed motor.
After replacing motor onto bracket with grommets and blade, don't completely tighten. Position plastic cover with hole opening over motor and blade assembly. Twirl motor blade to see if there is any interference with cover. If not, take away cover and tighten motor on bracket. If there is any rubbing, adjust motor/blade assembly accordingly before tightening in place. Putting everything back together is in reverse order.
After cleaning out freezer (plug disconnected first), start to remove outer plastic covers. If you want to keep track of the different steps, you can take pictures with your cellphone. And if there are any connecting wire attachments you think you might not remember, again, you can take a picture, or label with tape (colored tape, or by writing on the tape). And for keeping track of the different-size screws, I place them in a muffin tin, keeping an order of left to right and top to bottom in the tin. When removing Styrofoam blocks in bottom center, make sure you remove any remaining ice underneath in the hole so refrigerator can "breathe". Freezer air is moved below to refrigerator compartment, so a blocked vent hole will strain refrigerator as it tries to maintain its temperature setting and can be the cause of your failed motor.
After replacing motor onto bracket with grommets and blade, don't completely tighten. Position plastic cover with hole opening over motor and blade assembly. Twirl motor blade to see if there is any interference with cover. If not, take away cover and tighten motor on bracket. If there is any rubbing, adjust motor/blade assembly accordingly before tightening in place. Putting everything back together is in reverse order.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Lower part of refrigerator warm
16 of 19 people
found this instruction helpful.
-
bernard from Katonah, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Pulled refrigerator plug from socket.
Removed all freezer items. Put them into sink to keep cool.
Phillips head screwdriver removed screws from plastic housing fan cover from rear of freezer compartment.
Removed fan housing panel by lifting up and out. Panel has two small tabs that fit into back panel.
Removed back pan ... Read more el with phillips head screwdriver.
Fan is now exposed. Not working.
Plugged power cord back in.
Disconnected power adapter to fan.
Voltage meter sees power to ground and hot wire.
Fan not working
Unplugged power cord.
Removed fan from rear by socket tool.
Used hair dryer to remove ice build up in styrofoam insert between freezer compartment and lower section.
Removed foam insert....broke a couple of pieces off.
Test new motor with a line cord wire stripped at ends
Motor works. (Old one did not work with same test)
Replaced fan into bracket.
Replaced bracket into rear of freezer.
Plugged power cord in.
Fan does not work.....Whoa!!!..closed freezer door and heard fan running!!! It works.
Replaced everything...foam insert, panels, food.
One week later, still working.....
(Now...I don't know why the fan did not start right away...it may be that there's a small round thermostat sitting on a copper tubing, that needed some time to kick in...but that's a supposition.)
Have fun
Removed all freezer items. Put them into sink to keep cool.
Phillips head screwdriver removed screws from plastic housing fan cover from rear of freezer compartment.
Removed fan housing panel by lifting up and out. Panel has two small tabs that fit into back panel.
Removed back pan ... Read more el with phillips head screwdriver.
Fan is now exposed. Not working.
Plugged power cord back in.
Disconnected power adapter to fan.
Voltage meter sees power to ground and hot wire.
Fan not working
Unplugged power cord.
Removed fan from rear by socket tool.
Used hair dryer to remove ice build up in styrofoam insert between freezer compartment and lower section.
Removed foam insert....broke a couple of pieces off.
Test new motor with a line cord wire stripped at ends
Motor works. (Old one did not work with same test)
Replaced fan into bracket.
Replaced bracket into rear of freezer.
Plugged power cord in.
Fan does not work.....Whoa!!!..closed freezer door and heard fan running!!! It works.
Replaced everything...foam insert, panels, food.
One week later, still working.....
(Now...I don't know why the fan did not start right away...it may be that there's a small round thermostat sitting on a copper tubing, that needed some time to kick in...but that's a supposition.)
Have fun
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The condensor fan in the unit appeared to have been chewed by a mouse and would not function and the lower door was too low.
20 of 31 people
found this instruction helpful.
-
Eugene from Marion, TX
- Easy
- 1- 2 hours
-
Screw drivers, Socket set
The condensor fan in the unit appeared to have been chewed by a mouse and would not function. We had a service call to verify this and ordered the parts. Delivery was extremely quick and we were able to complete the repair and place the unit back into service within 2 hours.
All that was necessary was to remove the bottom card ... Read more board cover, replace the fan and grommets, and replace the door bushings.
Thanks!!
All that was necessary was to remove the bottom card ... Read more board cover, replace the fan and grommets, and replace the door bushings.
Thanks!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Motor was squeezing. Needed to be replaced.
14 of 14 people
found this instruction helpful.
-
Mark from BENICIA, CA
- Really Easy
- 30 - 60 mins
-
Socket set, Wrench (Adjustable)
Easy Peasey. Had to make one adjustment 24 hours later. Set the fan too far into the shroud. After the adjustment it works great!!!
Other Parts Used:
Was this helpful?
Thank you for voting!
The plastic cover broke - probably too many heavy bottles on it.
13 of 14 people
found this instruction helpful.
-
lotte from Laguna Woods, CA
- Really Easy
- 30 - 60 mins
Had to take out everything on the shelf & pull out the vegetable draws, then proceeded to clean it all. Had to take out the glass inset in the cover & wash that. After that I just slid it in - piece of cake! The hardest part was to get the plastic cover off the new part!
By the way - I'm 87 yrs old.
By the way - I'm 87 yrs old.
Was this helpful?
Thank you for voting!
we had a power surge that killed the fan motor
13 of 14 people
found this instruction helpful.
-
Richard from Wellsboro, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the fan housing , this was the hardest part , this took loosining two screws and snapping the housing loose , and there it was , settin there Idle and the coils were all ice , I let the coils thaw while I unscrewed the fan mount from the back wall of the freezer , then pulled the fan and mount out far enough to snap the wire con
... Read more
nector loose, then I removed the two screws that hold the motor to the mount , the new fan motor comes without the blade so the blade is removed by pulling fairly had on the center off the shaft , the old motor is taken out of the mount , the new one replaces it perfectly , then the screws are replaced and tightenen , then the blade is pushed back on the shaft , the motor and mount are placed back on the back wall of the freezer department and screwed in place , the wires connected , then the housing is snapped back in place and the screws tightened , turn the dial to cool or number 2 or 3 and " bingo " it,s just like new , I can thank part select for speedy service and delivery
Read less
Was this helpful?
Thank you for voting!
refrigerator
14 of 18 people
found this instruction helpful.
-
Charles from Baltimore, MD
- Really Easy
- Less than 15 mins
first i removed old gasket then pressed in new one very easy repair
Was this helpful?
Thank you for voting!