3641 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Switch failed on which kept the refrigerator warm due to heat generatered by light bulbs.
19 of 33 people
found this instruction helpful.
-
Terry from Simi Valley, CA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
While the switch did last for 9 years, the design is poor due to the failure mode. The failure should be to fail off or not able to turn on the lights which would be inconvenient but would not warm the refrigerator contents. Arcing at the contacts eventually caused the switch to "weld" closed. It is not obvious that this is occurring s
... Read more
o it took some time to recognize why the temp inside the ref was high while the freezer was OK. Replacing the switch was easy once it was recognized as the problem. All that was required to replace the switch was to remove the screws holding a fiber cover and then pulling off the aluminum cap which covered the switches. Unplug the switch an squeeze the keeper on the switch to release it and pull down. Pop the replacement switch in place and plug the wires harness back in. All in all it took much less time to replace than it has to write this up. T Pope
Read less
Was this helpful?
Thank you for voting!
Existing light switch was hard to remove.
14 of 19 people
found this instruction helpful.
-
Stephen from Jupiter, FL
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.
Was this helpful?
Thank you for voting!
Fan Motor stopped working
12 of 13 people
found this instruction helpful.
-
connie from omaha, AR
- Really Easy
- Less than 15 mins
-
Screw drivers
Not only was finding the part rediculously easy for a person who has never done this type of thing...the repair was a sinch!! I will always return to this company for help with home equipment repairs. I saved so much money doing it this way. :) thanks guys!
Was this helpful?
Thank you for voting!
malfunction of the cold control (wearing out after 15 years)
12 of 14 people
found this instruction helpful.
-
john from Philadelphia, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
1. Disconnected 120 VAC power supply from refrigerator. 2. Removed 2 philip screws from horizonal panel containing the thermostat. (Panel is in refrigerator section). 3. Removed plug module from panel which freed the pa
... Read more
nel which allowed me to remove panel to do repair. 4. Removed wires from thermostat (cold control), and mechanically removed thermostat from panel and installed new cold control (thermostat). Replaced wires on control. 5. Replaced panel and reinstalled 2 philips screws. 6. time to repair about 15 minutes.
Read less
Was this helpful?
Thank you for voting!
Bottom shelf of fridge that holds the drawers in place
13 of 18 people
found this instruction helpful.
-
Natalie from Bethlehem, AL
- Really Easy
- Less than 15 mins
I typed replacement fridge parts in google. Parts select.com came up. I found my fridge model # on the fridge and typed it in. A similar model # came up and I looked at the parts diagram. I determined what the piece was. I checked a couple other similar fridge model #'s to see if the part was the same. It was. Parts select made it so easy
... Read more
! I ordered the part on Monday in the afternoon... used regular shipping and had it in my hands by 9 am on Wednesday. I opened my fridge took out the collapsed bottom shelf (courtesy of my forever climbing 3 year old!) Installed the old glass and drawers in the new tray and Voila! as good as new! This couldn't of been a better experience from beginning to end,
Read less
Was this helpful?
Thank you for voting!
Interior light needed replaced
22 of 46 people
found this instruction helpful.
-
Leo from TWIN FALLS, ID
- Really Easy
- Less than 15 mins
-
Nutdriver
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Was this helpful?
Thank you for voting!
botton half of refrigerator not cooling
25 of 55 people
found this instruction helpful.
-
HANCEL from ELMONT, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
easy as 1.2.3 remove and replace before even thinking. just to let you know i also do this for a living but it is one of the most difficult thing when you have to stop and fix your own
Was this helpful?
Thank you for voting!
Fridge keeps cycling on and off and a clicking sound happens every time compressor cycles.
10 of 11 people
found this instruction helpful.
-
Kirk E from GRASS VALLEY, CA
- Easy
- Less than 15 mins
-
Screw drivers
I opened the back panel of the fridge and exposed the compressor. Unplugged existing run capacitor and installed new one with the addition of the sleeve that is stated must be installed around the run capacitor.
Everything I read and on this web site says that based on these symptoms, that the problem is the run capacitor. I search ... Read more ed and search for a part called a start relay which plugs in to the compressor. This run capacitor plugs in to this other part which I take as the start relay.
Installing this run capacitor did not solve the problem. The fridge compressor keeps cycling on and off. Freezer doesn't keep as cold as it should.
Everything I read and on this web site says that based on these symptoms, that the problem is the run capacitor. I search ... Read more ed and search for a part called a start relay which plugs in to the compressor. This run capacitor plugs in to this other part which I take as the start relay.
Installing this run capacitor did not solve the problem. The fridge compressor keeps cycling on and off. Freezer doesn't keep as cold as it should.
Read less
Was this helpful?
Thank you for voting!
Switchlight was broken on tennant's refridge
10 of 12 people
found this instruction helpful.
-
Mark from Somers Point, NJ
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapp
... Read more
ed the new switch into place.
10 minutes total.
10 minutes total.
Read less
Was this helpful?
Thank you for voting!
Vegetable shelf frame broke
9 of 9 people
found this instruction helpful.
-
paul from dahlonega, GA
- Really Easy
- Less than 15 mins
Took out the broken one and put in the new one just as the vido showed me how to. Took about 2 minutes.
Was this helpful?
Thank you for voting!
Evap Motor - loud noise
9 of 11 people
found this instruction helpful.
-
James from Floral Park, NY
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The evap fan, based on research, appears to be built to only last a few years. Pay attention to your order of removal for all pieces and it will go back rather easily in reverse.Remove items from freezer. UNPLUG FREEZER. Pop out the shelf. Use screwdriver to remove plastic piece in back. Pop out styrofoam piece. Use screwdriver to re
... Read more
move back metal section of freezer. Use nutdriver to remove screws holding the fan to the back. Unplug the motor. Pop off the fan. Pay attention to location of all these pieces. Put them on the new motor. Reassemble in reverse. Piece of cake.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Twice I ordered the oven light bulb & each time the light bulb was defected
18 of 38 people
found this instruction helpful.
-
Barbara from BELLEVUE, WA
- Very Difficult
- Less than 15 mins
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl
... Read more
iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Read less
Was this helpful?
Thank you for voting!
Rack holding vegetable trays were broken.
8 of 9 people
found this instruction helpful.
-
Ernest J from Slaughter, LA
- Easy
- Less than 15 mins
Simply changed the part.
Was this helpful?
Thank you for voting!
Overload switch failed on compressor. No cooling
8 of 9 people
found this instruction helpful.
-
phillip from hartselle, AL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unplug. Remove back cover. Remove retainer (simple wire clip) from overload. Unplug overload from compressor. Remove two power wires (if stabs are tight you might need pliers). Note which wire goes where. Remove capacitor from overload (just pul it straight out .. Pull hard or pry a little with screwdriver. Insert capacitor into new switc
... Read more
h. Reattach wires to same place in switch. Insert switch into compressor. Replace retainer clip. Replace rear cover with original screws. Plug in. Cool!
Read less
Was this helpful?
Thank you for voting!
Bearing chatter and slow running fan motor
10 of 15 people
found this instruction helpful.
-
Michael from Kalamazoo, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
assembled ordered parts then replaced defective fan and blade and bracket as a group
Other Parts Used:
Was this helpful?
Thank you for voting!