EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

356- - Instructions

All Instructions for the 356-
46 - 60 of 71

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light bulb failure
  • Grant from Alexandria, VA
  • Really Easy
  • Less than 15 mins
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this helpful?
Thank you for voting!
When The Burner Started To Heat (Front) And Then Put The Rice Bag On The Burner. Then The Plastic Bag Began To Burn And The Bag Of Rice Began To Pour Over The Burner. Someone Tried To Clean Up On The Burner But The Burner With Plastic And Hard To Clean The Plastic Off From The Burner.
  • Robert J from Indianapolis, IN
  • Really Easy
  • Less than 15 mins
Just pull the old out from the stove and put new one on the stove and then tested the burner that is working fine. Thank you very much for order the part. Have a great day.
Was this helpful?
Thank you for voting!
I needed to replace to two 8* drip bowls on the kitchen range
  • Dallas from Arlington, TX
  • Really Easy
  • Less than 15 mins
(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.
Was this helpful?
Thank you for voting!
Old dirty drip pans
  • gizella from mays landing, NJ
  • Really Easy
  • Less than 15 mins
Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!
Was this helpful?
Thank you for voting!
burner not operating or intermittently
  • Elroy from Atwater, MN
  • Easy
  • 15 - 30 mins
  • Nutdriver
Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.
Was this helpful?
Thank you for voting!
Electric surface burner would only turn very hot
  • Vittorio from Wakefield, MA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).
Was this helpful?
Thank you for voting!
burners would not come on without moving them around
  • Ronald E. from Marissa, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type thi s but i am slow at typing
Was this helpful?
Thank you for voting!
Burner did not heat
  • lula from Antelope, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
New receptacle element. I am a girl and I did it.!!!!
Was this helpful?
Thank you for voting!
heating coils would not work
  • Adam from Kempner, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.
Was this helpful?
Thank you for voting!
replacement of heating element for elec. stove
  • Erica from Ivyland borough, PA
  • Really Easy
  • Less than 15 mins
plugged it in to the spot where missing element was.
Was this helpful?
Thank you for voting!
Porcelan Electric Burner Plug broke
  • John J from Coatesville, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website .
Was this helpful?
Thank you for voting!
surface burner stopped working. Was not heating up.
  • timothy from south bend, IN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)
Was this helpful?
Thank you for voting!
Not heating
  • Darwin from wisconsin rapids, WI
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done
Was this helpful?
Thank you for voting!
Drip bowls tarnished.
  • Jennifer from Albion, NE
  • Really Easy
  • 15 - 30 mins
Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".
Was this helpful?
Thank you for voting!
Cartridge wire burned out
  • Robert from San Francisco, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.
Was this helpful?
Thank you for voting!
All Instructions for the 356-
46 - 60 of 71