EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

356- - Instructions

All Instructions for the 356-
16 - 30 of 71

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner receptacle failed (stove over 30 years old)
1 person found this instruction helpful.
  • BETH from COUNCE, TN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Was this helpful?
Thank you for voting!
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
1 of 2 people found this instruction helpful.
  • Nicki from ELSIE, NE
  • Very Easy
  • Less than 15 mins
No problem Took off old ones and replaced with new.
Was this helpful?
Thank you for voting!
Burners needed replacing
1 of 2 people found this instruction helpful.
  • Alene from INDIANAPOLIS, IN
  • Very Easy
  • Less than 15 mins
Pulled out the old burners and put in the new ones.
Was this helpful?
Thank you for voting!
Simple - needed to replace the drip pans on the stove between tenants in a rental apartment
1 of 2 people found this instruction helpful.
  • Tama from Pacific Grove, CA
  • Really Easy
  • Less than 15 mins
This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.
Was this helpful?
Thank you for voting!
Element had burned out
1 of 2 people found this instruction helpful.
  • Judith from Star, ID
  • Really Easy
  • Less than 15 mins
Package arrived while I was working at the computer and my husband announced minutes later, "That's what I like to see". I didn't know what he was talking about until he tossed the packing list on my desk and said, "It works perfectly. Good Job!" It had only taken a minute to pop the new parts in and he already had water on for coffee.
Was this helpful?
Thank you for voting!
Burner ceramic disintegrated & spalled
1 of 2 people found this instruction helpful.
  • Gary L from North Tonawanda, NY
  • Really Easy
  • Less than 15 mins
Pulled buner element out of socket as you would for detailed cleaning. Replaced burner element & drip pan with OEM parts. Fit was perfect, tested burner on all heat ranges, good as new.
Was this helpful?
Thank you for voting!
Old burner pan warped.burner sat at 15 degree angle.
1 of 2 people found this instruction helpful.
  • Michael from Portland, OR
  • Really Easy
  • Less than 15 mins
Removed burner and then burner pan.Then replaced pan and reinstalled burner.
Was this helpful?
Thank you for voting!
Large burner on stove not working
1 of 2 people found this instruction helpful.
  • Cherie from Dowagiac, MI
  • Really Easy
  • Less than 15 mins
I removed the heating element and noticed that the prongs were corroded. I looked for a model number but couldn't find it so it made it difficult to find a replacement until I got on this website. I found the replacement part and also found that as I checked for other sites for this part this company was the most resonable priced.
T he part arrived and I replaced it in seconds. Turned it on and it worked immediately. Super easy.
Was this helpful?
Thank you for voting!
Burner plugs were loose
1 of 2 people found this instruction helpful.
  • James from CONCORD, NC
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
used the supplied parts...very easy. The parts were exact replacements.
Was this helpful?
Thank you for voting!
burned out stove eye, 6"
1 of 2 people found this instruction helpful.
  • Robert from Birmingham, AL
  • Easy
  • 15 - 30 mins
remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people found this instruction helpful.
  • Ivanka from Atlantra, GA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh t bulb in was not the problem.
Was this helpful?
Thank you for voting!
The burner was shortening out and would work sometime. The first time I replace the burner but the new one shorted out quickly.
1 of 3 people found this instruction helpful.
  • shawn from Vancouver, WA
  • Really Easy
  • Less than 15 mins
  • Pliers
I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.
Was this helpful?
Thank you for voting!
Receptacle had become bad poor connection.
1 of 3 people found this instruction helpful.
  • JAMES from Harrodsburg, KY
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.
Was this helpful?
Thank you for voting!
surface element burnout
0 of 1 people found this instruction helpful.
  • david from wellsboro, PA
  • Really Easy
  • Less than 15 mins
The repair was just a matter of sliding the old one out and plugging the new one in. The ease of use of this website was wonderful. Super fast shipment. Im very pleased.
Was this helpful?
Thank you for voting!
replaced oven lightbulb
0 of 1 people found this instruction helpful.
  • peggy ann from forest city, NC
  • Really Easy
  • Less than 15 mins
very easy
Was this helpful?
Thank you for voting!
All Instructions for the 356-
16 - 30 of 71