3524 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
lower oven heating element failed
0 of 1 people
found this instruction helpful.
-
Charles from Avoca, PA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Power off by unplugging appliance!
Remove the old element by removing one screw from each of the old element anchoring tabs.
Pull element away from back of oven approx. 3 inches to expose spade lug electrical connectors.
With the pliers, gently seperate the spade connector from the element connecting tab.
Remove old el ... Read more ement.
Install new element in reverse order.
Plug appliance in, set oven to warm/low heat to test and burn off any metal preserveative from elemnt surface.
Check operation by allowing to heat for < 30 seconds. Oven element should start to warm and can be confirmed by breifly placing hand a few inches away from element to detect heat.
Turn oven off if satisfactory. Reset time on oven clock. Finis!!!!
Remove the old element by removing one screw from each of the old element anchoring tabs.
Pull element away from back of oven approx. 3 inches to expose spade lug electrical connectors.
With the pliers, gently seperate the spade connector from the element connecting tab.
Remove old el ... Read more ement.
Install new element in reverse order.
Plug appliance in, set oven to warm/low heat to test and burn off any metal preserveative from elemnt surface.
Check operation by allowing to heat for < 30 seconds. Oven element should start to warm and can be confirmed by breifly placing hand a few inches away from element to detect heat.
Turn oven off if satisfactory. Reset time on oven clock. Finis!!!!
Read less
Was this helpful?
Thank you for voting!
old element broke
0 of 1 people
found this instruction helpful.
-
paul from davie, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
unscrew 2 screws, pull 2 connectors off, put in new part in reverse order - easy fix.
Was this helpful?
Thank you for voting!
Bake Element Broke in half
0 of 1 people
found this instruction helpful.
-
Rick from Linden, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Took out 2 screws pulled off the 2 female connectors. put the conectors on the new element and put the screws in. It took less than 10 minutes
Was this helpful?
Thank you for voting!
element broke in 3 pieces
0 of 1 people
found this instruction helpful.
-
charles from moody, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
turned off power removed old element .connected new element reinstalled works fine .part fit was correct part first time something rare in this day and age.
Was this helpful?
Thank you for voting!
Heat element on the bottom caught on fire, burned out, had to replace
0 of 1 people
found this instruction helpful.
-
Christine from Lansing, MI
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
The previous repair stories were extremely helpful! The most difficult part was unhooking the old element and I assume some of that was contributed by it's age. Installing was a piece of cake!
Was this helpful?
Thank you for voting!
oven would't heat
0 of 1 people
found this instruction helpful.
-
John from Janesville, WI
- Really Easy
- Less than 15 mins
-
Screw drivers
Disconnected power plug,had to clean behind oven! , then...... removed 2 screws that held element in place, pulled element out about 3 inches disconnected 2 wires, removed old element, slide in new one, connected 2 wires, slide coil in carefully, and replaced 2 screws, replaced power plug checked operation, (worked fine) slide oven back i
... Read more
nto place....wife was happy.
Read less
Was this helpful?
Thank you for voting!
The oven did not heat up. I noticed the element was cracked.
0 of 1 people
found this instruction helpful.
-
Bill from Valhalla, NY
- Easy
- Less than 15 mins
-
Screw drivers
I watched the video provided by Part Select before I ordered the part. I removed the old element by taking out two screws and unplugging it from the wires. I put the new element in place, connected the wire to the right side and then opened up the back of the range to connect the left side. The repair was easy, but the video did not sh
... Read more
ow that you had to connect the left side from the rear of the appliance. It was easy to figure out. The appliance works like a charm...no like an oven.
Read less
Was this helpful?
Thank you for voting!
heating element burned out
0 of 1 people
found this instruction helpful.
-
Amanda from Columbia, MO
- Easy
- Less than 15 mins
-
Pliers
We repalced the heating element n no time. Easy to do and the price couldn't be beat!
Was this helpful?
Thank you for voting!
Element burned into several pieces
0 of 1 people
found this instruction helpful.
-
Jeff from lansing, MI
- Easy
- Less than 15 mins
-
Screw drivers
Simple repair.Just make sure you measure the length of element from back wall to plug in,width,and width of holes in back of oven.Simple repair with correct measurements.Pluged it in replaced screws plugged power back to unit , worked like a charm....Thank You!!!
Was this helpful?
Thank you for voting!
Element was heating only in spots
0 of 1 people
found this instruction helpful.
-
Diana from Webberville, MI
- Easy
- Less than 15 mins
-
Nutdriver, Pliers
Removed back of stove (6 screws), puled clips loose. Two screws inside oven, pulled out old element. slid new one in, replaced screws, slid on clips replaced back panel. Don't forget to unplug the stove frist.
Was this helpful?
Thank you for voting!
heating element broke
0 of 1 people
found this instruction helpful.
-
jeffrey from st louis, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
Very easy, clip on connections and two screws to hold it in place.
Was this helpful?
Thank you for voting!
no problem
0 of 1 people
found this instruction helpful.
-
Arquetta from Phoenix, AZ
- Really Easy
- Less than 15 mins
It was very easy to fix
Was this helpful?
Thank you for voting!
The lower oven element burnt out.
0 of 1 people
found this instruction helpful.
-
Rosemarie from Missoula, MT
- Really Easy
- Less than 15 mins
-
Screw drivers
After removing the old broken element, I searched the internet for the part by brand and model number. With very little trouble, I located the correct part, ordered it and waited for the notice of shipment. In 5 days, and that included Memorial weekend we had the part and in 5 minutes the part was installed. The cost was $31.20 plus sh
... Read more
ipping..not bad!
Read less
Was this helpful?
Thank you for voting!
Baking element had burned out.
0 of 1 people
found this instruction helpful.
-
Charles from Waynesboro, VA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Followed the instructions exactly as described on the Parts web site video, shut off power, removed old baking element, checked connectors, replaced with new element, turned power back on to the range. Repair took less than 15 minutes.
Was this helpful?
Thank you for voting!
Bake element failed
0 of 1 people
found this instruction helpful.
-
Claude from West Frankfort, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed two screws that attach bake element to rear of oven. Slid off blade type connectors at each end. Slid connectors onto new element. Pushed element into place and reinstalled two screws. Tested. Perfect. Took longer to do this survey than to do the repair! The one day shipping service was a big plus.
Was this helpful?
Thank you for voting!