3521 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
one electric burner does not get hot
5 of 10 people
found this instruction helpful.
-
dinh from austin, TX
- Easy
- 15 - 30 mins
-
Screw drivers
swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. U
... Read more
sed the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.
Read less
Was this helpful?
Thank you for voting!
Broiler drawer didn't track poperly
3 of 4 people
found this instruction helpful.
-
Keith from Atlanta, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove screw securing the broken drawer guide. Placed new drawer support in place and tightened screw. Replaced drawer. All done in less than 5 minutes (and cheaply).
Was this helpful?
Thank you for voting!
Broiler front drawer slides broke
3 of 4 people
found this instruction helpful.
-
Ernie from Fremont, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I noticed the drawer on the broiler was sliding crooked and found the plastic slides had broken. Of course I thought it would be a hassle and not worth the time to fix it. I would just "live with it". Boy was I wrong, it was probably the simplest fix ever. It was easy to get the correct parts from PartSelect with their exploded and concis
... Read more
e diagram. The parts were ordered and delivered in a couple of days. It took me all of 10 minutes with a screwdriver to make the repairs. Now it is a good as new.
Read less
Was this helpful?
Thank you for voting!
piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.
3 of 4 people
found this instruction helpful.
-
George from Irving, TX
- Really Easy
- Less than 15 mins
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
Other Parts Used:
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Baking element burned out
2 of 2 people
found this instruction helpful.
-
Stephen from Pleasant Hill, IA
- Easy
- Less than 15 mins
-
Screw drivers
I watched the video on the web site and it worked like a dream. Two screws to take out - disconnect wires put back connecting wires and replace the screws again. Just like the video. Thanks
Was this helpful?
Thank you for voting!
replaced old drip pans
3 of 5 people
found this instruction helpful.
-
Frances from Summerfield, FL
- Really Easy
- Less than 15 mins
Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!
Other Parts Used:
Was this helpful?
Thank you for voting!
Bake element caught on fire
2 of 2 people
found this instruction helpful.
-
Dan from TomRriver, NJ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I got the run around about my HARWICK stove at several part stores. Like they all said the same thing (cant look it up just bring it down) So i did and then they would say, what's the model number. ERR! SO my wife found parts select on the web and they beat the three price quotes I got. First turn the power off to the stove!!! The repair
... Read more
was simple. Just remove the two screws on both side's and pull the element out but just enough for the wire's to show. Disconnect the two wire's and pull the element out. Reverse the processes but when wire's are reconnected squeeze terminals end gently to ensure a good connection. This is a great company to deal with, I will be using them again. Thanks and good luck!!!
Read less
Was this helpful?
Thank you for voting!
light wouldn't come out of socket
3 of 5 people
found this instruction helpful.
-
Joyce from Tacoma, WA
- Really Easy
- Less than 15 mins
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this helpful?
Thank you for voting!
Drip pans were not original to range, I could not get them clean.
2 of 2 people
found this instruction helpful.
-
Lynn from BRADENTON, FL
- Really Easy
- Less than 15 mins
I reoved old drip pans and installed new ones. Very easy, they look great!
Other Parts Used:
Was this helpful?
Thank you for voting!
The element on my 20+ year old Jenn Zaire oven had broken in two...
2 of 2 people
found this instruction helpful.
-
Mary from New Britain, PA
- Very Easy
- Less than 15 mins
-
Screw drivers
Went online to find replacement part. (Because I’m cheap) Came across the website, found the part by model number, and watched the wonderful replacement video that was right on the same page as the part. After the part arrived, (in just a couple of days) I put the new one in. Only took a couple of minutes! Perfection! Thanks for making m
... Read more
y problem, no problem at all!
Read less
Was this helpful?
Thank you for voting!
1960's oven door gasket fell apart, actual gasket not available any more
2 of 2 people
found this instruction helpful.
-
Mary from WINCHESTER, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Was this helpful?
Thank you for voting!
Burner control knob/switch shaft had broken off.
4 of 8 people
found this instruction helpful.
-
Steve from San Luis Obispo, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.
Was this helpful?
Thank you for voting!
Bake Element wouldn't heat up to temperature
2 of 2 people
found this instruction helpful.
-
John from Foxboro, MA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
I had viewed the video link on PartsSelect. I removed 2 screws and proceeded to pull element out to disconnect wire connectors. However one side the wire connected was melted on to the contact tab of the element and the wire was broken off. I proceeded to remove back panel from stove and located the exposed broken wire. I stripped back wi
... Read more
re and installed a new wire connector that I had in my tool box. I fed wire through small hole. Then I re-installed back panel. I then connected wires to the new bake element and installed element mounting screws.
Read less
Was this helpful?
Thank you for voting!
Frayed and exposed receptical wires in cartridge
2 of 3 people
found this instruction helpful.
-
Richard C from San Jose, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridg ... Read more e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridg ... Read more e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
Read less
Was this helpful?
Thank you for voting!