EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3521 - Instructions

All Instructions for the 3521
46 - 60 of 422

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
light bulb in water ice freezer door went bad
8 of 14 people found this instruction helpful.
  • Carl from RIVERSIDE, CA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
6" surface heating coil remained warm when "off"
8 of 15 people found this instruction helpful.
  • William C. from Sealy, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers
Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sl eeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.
Was this helpful?
Thank you for voting!
Stove seal fell apart
5 of 6 people found this instruction helpful.
  • Teresa from Washougal, WA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.
Was this helpful?
Thank you for voting!
Bake Element Failed
5 of 6 people found this instruction helpful.
  • Douglas from Plymouth, WI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplugged the stove. I removed the old element by removing the two screws holding it in, and plugged the stove back in. I ordered the part and it came in 2 days. Unpluged the stove again, connected the new element, and re-attached it via the two screws. Plugged it back in, and it worked great. Fantastic price and quick delivery. Only too k about 5 minutes to fix, and I saved at least $100 by not having to call a service man.
Was this helpful?
Thank you for voting!
Store-bought drip bowls wouldn't fit.
5 of 6 people found this instruction helpful.
  • Sharon from Yacolt, WA
  • Really Easy
  • Less than 15 mins
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!
Was this helpful?
Thank you for voting!
The heating element socket had crumbled with age.
4 of 4 people found this instruction helpful.
  • Edward from Webster, NY
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.
Was this helpful?
Thank you for voting!
power light on, but burner not getting hot
7 of 13 people found this instruction helpful.
  • Aaron from Weymouth, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.
Was this helpful?
Thank you for voting!
The drip bowls were all caked and corroded.
4 of 5 people found this instruction helpful.
  • Terry from Mountain City, TN
  • Really Easy
  • Less than 15 mins
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)

I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
Was this helpful?
Thank you for voting!
Broken levelling leg
5 of 8 people found this instruction helpful.
  • Linda from Oneida, NY
  • Really Easy
  • Less than 15 mins
Took the old levelling leg out and screw the new one in.
Was this helpful?
Thank you for voting!
Burner no longer worked.
4 of 5 people found this instruction helpful.
  • Marcus from Emmett, KS
  • Easy
  • Less than 15 mins
  • Screw drivers
First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!
Was this helpful?
Thank you for voting!
oven door gasket torn
4 of 5 people found this instruction helpful.
  • Ovide N from Abbeville, LA
  • Really Easy
  • Less than 15 mins
ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job
Was this helpful?
Thank you for voting!
Broiler drawer front slide plastic guides broke so drawer sagged and was difficult to pull out.
3 of 3 people found this instruction helpful.
  • DOUGLAS from MESA, AZ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the single phillips screw that held each plastic slide guide to the stove, and replaced the part reusing the screws. Was so simple I didn't even have to swear. This was my mother-in-law's stove, and she was so happy to have it repaired she's fed me twice since.
Was this helpful?
Thank you for voting!
Old element caught fire, replaced with new one
3 of 3 people found this instruction helpful.
  • louis from CAHOKIA, IL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Removed screws of old element pulled clips off replaced with new element very easy
Was this helpful?
Thank you for voting!
freezer compartment worked fine but very little cooling going to refrigerator section.
3 of 3 people found this instruction helpful.
  • Lee from OZARK, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The re placement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Was this helpful?
Thank you for voting!
Burner wouldn't heat (wiring failure)
3 of 4 people found this instruction helpful.
  • Eugene from San Antonio, TX
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench set
1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
Was this helpful?
Thank you for voting!
All Instructions for the 3521
46 - 60 of 422