3424 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
evaporator coil kept freezing up, refridgerator warm.
186 of 209 people
found this instruction helpful.
-
Greg from Hanover Township, PA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
This was the second part I tried. The defrost timer was first, but that did not fix it. To do this I had to remove the ice maker and the back plate of the freezer. Then I defrosted the coil and cut the wires. stripped them back and installed the new thermostat. re-assembled and tested. has been working great ever since.
Was this helpful?
Thank you for voting!
Refrigerator would not run but interior light was on.
184 of 248 people
found this instruction helpful.
-
Bruce from Alton, IL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I unplugged the refrigerator, then opened the door and removed four screws holding the plastic electrical panel to the interior top of the main refrigerator compartment and noticed the cold control was corroded badly, apparently from moisture in the panel. I ordered a new one from partselect.com. When it arrived the next day, I then pul
... Read more
led off the control knob, unclipped the cold control, unplugged the three wires to the control, then removed the styrofoam insulation blocks holding the thermocouple wire and then removed the thermocouple wire to complete the removal. I then reversed the process to install the new thermostat and control. That is repositioned the thermocouple wire, put the insulation blocks back to hold the wire, then replugged the three electrical wires, clipped the control back and pushed the control knob back on and finally screwed the panel back to the top of the main compartment and plugged the refrigerator electrical cord back in to provide current to the refrigerator. It immediately started up and ran fine. Total time - about 8 minutes.
Read less
Was this helpful?
Thank you for voting!
refrigerator would'nt cool
22 of 31 people
found this instruction helpful.
-
arthur from doral, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
first i removed the four screws that hold the shelve in place disconnected the wire replace both diffuser-air,reconnected the wire and replaced the screws
Other Parts Used:
Was this helpful?
Thank you for voting!
Light Socket short
22 of 31 people
found this instruction helpful.
-
Rebecca from Gautier, MS
- Really Easy
- Less than 15 mins
- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.
Was this helpful?
Thank you for voting!
Replaced the heater-core motor
17 of 22 people
found this instruction helpful.
-
John from Roanoke, VA
- Easy
- 15 - 30 mins
-
Socket set
It was fairly easy. Only had to remove the back cardboard. Remove 3 screws and the power plug.
Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.
Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.
Was this helpful?
Thank you for voting!
Shattered crisper pan glass
16 of 21 people
found this instruction helpful.
-
Stacia from Salem, OH
- Really Easy
- Less than 15 mins
I slid the new glass in place
Was this helpful?
Thank you for voting!
cracked bottom hinge
16 of 21 people
found this instruction helpful.
-
LEE from LEO, IN
- Really Easy
- Less than 15 mins
-
Socket set
My 4 year old grandson used the frig door as a swing.The bottom hinge cracked, then the door wouldn't seal. I propped the door up with some books, removed the broken hinge (2 bolts) and replaced with the new part. Simple fix on the door, only time will fix the 4 year old!
Was this helpful?
Thank you for voting!
Fan motor no longer functioning and needed to be replaced
12 of 12 people
found this instruction helpful.
-
Amber from SHERMANS DALE, PA
- Very Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Socket set
The most difficult part was the removal of the existing fan and shroud. There is very little room to work between the condenser and the coils where the fan is located. The old shroud had to be removed as it was not compatible with the mounting for the new fan motor and blade. Make sure to unplug the refrigerator and give the coils some
... Read more
time to cool down. The first step was to remove the old fan blade... it simply pulls off. Next you need to remove the two bolts holding the fan shroud to the floor of the refrigerator. Then you need to remove the old fan motor from the shroud... unplug the wire connection and remove two small bolts that hold it on. I was lucky to have a VERY small ratchet to get into these tight spaces. Now is the really hard part, removing the metal fan shroud takes a lot of twisting and turning to get it out. The coils have a little play in them, but you must be very careful of the tubing and connections. Also, the coils are very sharp. Once this is out, IF you can get it out....I had my doubts along the way, you can start to put the new parts in... beginning with the new fan shroud which fortunately is made of plastic and has some give which makes it easier to get in. Then you can mount the new motor to the shroud with the three new screws. Plug in the wire connection, add the foam tape to the shroud and mount the shroud to the floor of the frig with the original two bolts. Lastly, attach the fan blade. This replacement kit is well constructed, fits perfectly and contained all the necessary parts (fan motor with wiring connection, mounting screws, wire connection adapter, fan shroud, foam tape and fan blade), but no detailed instructions come with it. I was lucky to get the old fan shroud out without doing any damage to the surrounding parts, but this part was very difficult for a do it yourself person. I would be interested to know if a professional has some other tips for this part of the replacement process.
Read less
Was this helpful?
Thank you for voting!
Leaky Seal
11 of 14 people
found this instruction helpful.
-
Travis from Tecumseh, OK
- Really Easy
- Less than 15 mins
Just snaps in. Pull the old one out push the new one in. It has a groove it fits into no fasteners to undo, Just pull the old one out with steady pressure.
Was this helpful?
Thank you for voting!
Not running
10 of 12 people
found this instruction helpful.
-
Kenneth from SAVANNAH, GA
- Really Easy
- Less than 15 mins
-
Nutdriver
After waiting over 2wks for my part to arrive, I purchased the part locally and made the repair the same day as I am still waiting for the part to arrive from you guys. Your customer service really needs improving. I paid for 2 day shipping, what a joke. I will be returning the part as soon as I receive it thanks.
Was this helpful?
Thank you for voting!
Cracked drawer
8 of 11 people
found this instruction helpful.
-
Jaime from Harrisburg, PA
- Really Easy
- Less than 15 mins
I slid out the old drawer and slid in the new drawer. Easy as that! I would recommend this website to anyone.
Was this helpful?
Thank you for voting!
Big oops when I broke the glass shelf while washing in hot water...too hot
8 of 12 people
found this instruction helpful.
-
LYNETTE from AGOURA HILLS, CA
- Really Easy
- Less than 15 mins
I ordered the part, it arrived within 48 hours. I opened the fridge and put the shelf in perfectly!
Was this helpful?
Thank you for voting!
broken glass insert over refrigerator drawers
6 of 6 people
found this instruction helpful.
-
Margaret from McLean, VA
- Really Easy
- Less than 15 mins
I called in because the model # of the refrigerator did not show up on the website. The cust. srvc. rep looked it up and found the part. It was reasonably priced, I received it in a matter of days and it fit perfectly. Thank you! We were preparing to put the condo on the market and broke the shelf while cleaning. It was great to have
... Read more
a resource for a reasonably priced replacement and quick shipment.
Read less
Was this helpful?
Thank you for voting!
Freezer compartment warm / Ice cream soft
9 of 15 people
found this instruction helpful.
-
George from McBee, SC
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set
I worked for GM as a Frigidaire Tech, before starting my own business. I have retired now.
I took the three screws off the back of the bracket holding the motor. Disconected wire harness and pulled out the motor. Reverse to install. [email protected]
I took the three screws off the back of the bracket holding the motor. Disconected wire harness and pulled out the motor. Reverse to install. [email protected]
Was this helpful?
Thank you for voting!
fan motor quit working
4 of 4 people
found this instruction helpful.
-
Phillip from SUNDANCE, WY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
A little difficult getting out due to restricted space, I took off the fan blade, that gave extra working room. Then it went well going back together,and it all worked as advertised. Thanks. p
Was this helpful?
Thank you for voting!