EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3422 - Instructions

All Instructions for the 3422
121 - 135 of 592

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven burner would periodically go out and re-light
3 of 4 people found this instruction helpful.
  • Richard from Merrimac, MA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.

Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.
Was this helpful?
Thank you for voting!
No Ice !
3 of 4 people found this instruction helpful.
  • Kevin from Bridgewater, NJ
  • Easy
  • 15 - 30 mins
  • Nutdriver
Real simple repair..just backed off the two 1/4" hex bolts holding the ice maker to the wall of the fridge,(a little tricky since you can't see them),unclipped the electrical doo hickey. I re-clipped the electrical do hickey of the new ice maker, hung the ice maker on the bolts and then re-tightened them. However,still no ice,my problem w as the water valve on the back of the fridge behind the cardboard. Although it was still giving H2O thru the door it was not allowing water to flow to the ice maker. I reccommend pouring some water into the ice tray of the ice maker. If it makes ice and dumps it in to the holder, your ice maker is OK. If it turns out to be your water valve, that fix is easy as well. I HIGHLY reccommend watching the "fix it" video associated with that part. That repair also took less than 15 minutes. Good Luck! KC Bridgewater,NJ
Was this helpful?
Thank you for voting!
Oven taking to long to preheat.
3 of 4 people found this instruction helpful.
  • Isaac from LATHRUP VLG, MI
  • Very Easy
  • 30 - 60 mins
  • Screw drivers
Accessed igniter removed 2screws holding it.unpluged igniter installed new one.
Was this helpful?
Thank you for voting!
Ice maker would not dischare ice
3 of 4 people found this instruction helpful.
  • DAVE from CRESTON, IA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Followed the online video from this site
Was this helpful?
Thank you for voting!
The ice crushing housing was broken.
2 of 2 people found this instruction helpful.
  • Les from LIVERMORE, CA
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
The repair went easily after watching the video, took me less than an hour to complete the repair.
Was this helpful?
Thank you for voting!
Ice maker stopped working
2 of 2 people found this instruction helpful.
  • Joseph from Seal Beach, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
First I determined the icemaker was the problem when it was no longer calling for water. You can hear that "whistle" for 6-7 seconds when it calls for water. Anyway, replacement was a piece of cake, but did not entirely fix my problem. I also had to flush the lines to the soloniods that allow water to flow through the filter and into the water storage tank because it was cloggged with a little piece of plastic.
Was this helpful?
Thank you for voting!
igniter burned out
2 of 2 people found this instruction helpful.
  • David from Milton, MA
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Wrench set
Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.
Was this helpful?
Thank you for voting!
Door would not close properly.
2 of 2 people found this instruction helpful.
  • Brian from ROY, UT
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
Remove the food items from the shelves on the door, Phillips screwdriver to take the top cap off. Adjustable wrench to take the two screws off the top hinge. Lift out the door and set aside. Remove two bolts from the lower hinge, reinstall with the new hinge and spacer. Reinstall door on lower hinge. Lift into place to reattach the upper hinge. Put the food back in and you're done.
Was this helpful?
Thank you for voting!
Ice crusher selection door broken
2 of 2 people found this instruction helpful.
  • shawn from CORTEZ, CO
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to p osition.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.
Was this helpful?
Thank you for voting!
Dispenser Crusher Housing was broken
2 of 2 people found this instruction helpful.
  • Pete from THE PLAINS, OH
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on e ach side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23
Was this helpful?
Thank you for voting!
Ice Crusher Houseing cracked broke into pieces
2 of 2 people found this instruction helpful.
  • Curtis from ROCK HILL, SC
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Remove ice drawer ,Removed front of drawer 4 screws ,Removed broken crusher 3 screws Ordered new parts reassembled replaced fix blade spacer that was broken and blade cover housing reattached front of drawer !
Was this helpful?
Thank you for voting!
Part broke though normal use
7 of 17 people found this instruction helpful.
  • Hugh from Berthoud, CO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.
Was this helpful?
Thank you for voting!
Part 30 on the Ice and water dispenser drawing was broken and needed to be replaced in order to seal the ice chute opening into the freezer.
2 of 2 people found this instruction helpful.
  • Jon from SEBRING, FL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Followed the video for this repair. Only issue was that the videos showed that when the front panel is removed, there is a wire harness that has to be unplugged from part No. 38c. This was not the case. What I had was a Ribbon Cable Harness that plugged into the front of part No. 38 and the top of part 38C (the two power boards) I tried to disconnect it from part 38C by pulling it out, and apparently damaged the Ribbon Cable Harness. Later found a video showing how to remove this item properly when replacing power boards 38 and 38C. Have ordered a new cable from GRP and hopefully this will solve the problem, as there is no electrical current to the dispenser controls and the ice and water dispenser are not currently working. Would have been nice to know that there are two types of connections between these power boards; a cable harness that unplugs from 38C or a Ribbon Cable Harness that unplugs from from the face of part No. 38. Hopefully I have not damaged either of the boards or anything else. Professional repair man coming on Thursday to test the boards, micro switches, etc. The boards are quite pricey, ($550.00 for both) and since the refrigerator was manufactured in 2004, we will buy a new one before we pump any more into this older unit. Very important to know how to unplug this Ribbon Cable Harness from the boards before proceeding ! Plug in on 38C is very tricky and you will need to review a video showing how it is done.
Was this helpful?
Thank you for voting!
oven would not light
2 of 2 people found this instruction helpful.
  • gary from covington, LA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.
Was this helpful?
Thank you for voting!
Oven would not ignite
2 of 2 people found this instruction helpful.
  • Dominick from CLARKS SUMMIT, PA
  • Very Easy
  • Less than 15 mins
  • Screw drivers, Wrench set
Very easy, video helped tremendously
Was this helpful?
Thank you for voting!
All Instructions for the 3422
121 - 135 of 592