3141 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
igniter burned out
2 of 2 people
found this instruction helpful.
-
David from Milton, MA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.
Was this helpful?
Thank you for voting!
oven would not light
2 of 2 people
found this instruction helpful.
-
gary from covington, LA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.
Was this helpful?
Thank you for voting!
RIGHT HINGE BROKE
2 of 3 people
found this instruction helpful.
-
Heinz from SARASOTA, FL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Removed 2 hidden screws from the top panel.
Lifted top panel.
The first screw came out easy, the second one gave me trouble.
It is best to help a helper who can hold the lid open as much as possible.
To insert the new screws takes patience as they might fall very easily.
Overall, not that difficult - just need pat ... Read more ience.
Lifted top panel.
The first screw came out easy, the second one gave me trouble.
It is best to help a helper who can hold the lid open as much as possible.
To insert the new screws takes patience as they might fall very easily.
Overall, not that difficult - just need pat ... Read more ience.
Read less
Was this helpful?
Thank you for voting!
oven would not turn on
2 of 3 people
found this instruction helpful.
-
Robert from Clymer, NY
- Easy
- 15 - 30 mins
-
Screw drivers
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and rep
... Read more
laced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Read less
Was this helpful?
Thank you for voting!
The right plastic hinge broke
2 of 3 people
found this instruction helpful.
-
Ralph from Thomasville, GA
- Easy
- 15 - 30 mins
-
Screw drivers
The instructions received from partselect.com were really good. There are two long screws located on either side of the front control panel. Simply removed the small covers to expose the two screws. Then remove both screws. At that point you can lift up (carefully) the front panel high enough to gain access underneath to remove the two Ph
... Read more
ilip head screws holding the hinge. Be careful not to drop the screws down in the machine cavity. Lift out the old hinge and insert the new one. Re-install the two Phillip head screws into the new hinge. Let the front panel back down and re-install the two long screws. You’re done!
Read less
Was this helpful?
Thank you for voting!
igniter glowed but oven would not light
2 of 3 people
found this instruction helpful.
-
edward from euclid, OH
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed
... Read more
six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Read less
Was this helpful?
Thank you for voting!
Plastic hinge broken on RHS.
2 of 3 people
found this instruction helpful.
-
David from SHELBY TWP, MI
- Really Easy
- 30 - 60 mins
-
Screw drivers
Description provided on website was that repair was similar to another washing machine where you press in on spring clips to release top of machine to access hinge. Not correct at all.
There are two screws on top of machine that are covered by caps. Remove caps and then remove screws. Lift up / prop up machine top and you have ... Read more easier access to 2 screws that hold plastic hinge in place. Remove screws and replace hinge and replace screws. Took me longer to figure out I had incorrect directions than it did to replace hinge.
There are two screws on top of machine that are covered by caps. Remove caps and then remove screws. Lift up / prop up machine top and you have ... Read more easier access to 2 screws that hold plastic hinge in place. Remove screws and replace hinge and replace screws. Took me longer to figure out I had incorrect directions than it did to replace hinge.
Read less
Was this helpful?
Thank you for voting!
Drain hose had a pin hole leak external to washer
3 of 6 people
found this instruction helpful.
-
Terry from SIMI VALLEY, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.
The one difference from the existing install video online was that I didn't ... Read more have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).
The one difference from the existing install video online was that I didn't ... Read more have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).
Read less
Was this helpful?
Thank you for voting!
leg broke off inside housing
5 of 12 people
found this instruction helpful.
-
thomas m from CARMICHAEL, CA
- A Bit Difficult
- Less than 15 mins
raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new
... Read more
leg was a breeze.
Read less
Was this helpful?
Thank you for voting!
Install valve knobs
3 of 6 people
found this instruction helpful.
-
Donald from Peebles, OH
- Really Easy
- Less than 15 mins
This was not a difficult task. I just slid the valve knob on the shaft, repair was complete. This was a very easy diy project.
Was this helpful?
Thank you for voting!
Broken burner knobs on stove.
2 of 3 people
found this instruction helpful.
-
Barbara L. from Tewksbury, MA
- Really Easy
- Less than 15 mins
Just replaced the old burner knobs with the new !!!
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people
found this instruction helpful.
-
Rhoda P. from Secaucus, NJ
- Really Easy
- Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Other Parts Used:
Was this helpful?
Thank you for voting!
oven would not heat up fully, smelled of gas.
1 person
found this instruction helpful.
-
Brian from Spotswood, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this helpful?
Thank you for voting!
Stove Would Not Light To Heat Up.
1 person
found this instruction helpful.
-
Nola from Enid, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
Was this helpful?
Thank you for voting!
igniter failed to ignite
1 person
found this instruction helpful.
-
Gino from ARLETA, CA
- Really Easy
- Less than 15 mins
-
Socket set
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this helpful?
Thank you for voting!