EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3141 - Instructions

All Instructions for the 3141
46 - 60 of 312

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water leaking into drum
4 of 5 people found this instruction helpful.
  • Richard from RED LION, PA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Figured out how to remove the top door and the top panel that covered the solenoid bank. That was the hardest part. Swapping out the solenoid bank and the connector was easy. No more water leaking.
Was this helpful?
Thank you for voting!
Low water flow into washer
4 of 5 people found this instruction helpful.
  • Alexander from SALISBURY MLS, NY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Replaced valve body, very easy to fix as per the video, runs normal.
Was this helpful?
Thank you for voting!
oven wouldn't light
4 of 5 people found this instruction helpful.
  • peter from marine city, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to f ully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Was this helpful?
Thank you for voting!
oven door gasket torn
4 of 5 people found this instruction helpful.
  • Ovide N from Abbeville, LA
  • Really Easy
  • Less than 15 mins
ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job
Was this helpful?
Thank you for voting!
Oven wouldn't heat.
3 of 3 people found this instruction helpful.
  • Thomas from La Crescenta, CA
  • Easy
  • Less than 15 mins
  • Nutdriver
Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pus hed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.
Was this helpful?
Thank you for voting!
Oven wouldn't heat/ turn on
3 of 3 people found this instruction helpful.
  • Diane from NEW HAVEN, MO
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.
Was this helpful?
Thank you for voting!
The old water assembly valve split on the bottom and started leaking.
4 of 6 people found this instruction helpful.
  • Jerry from CARYVILLE, TN
  • Very Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After unplugging the washer I cut the water off. I took the water hoses off, then the back top panel using a phillips head screw driver. I then used a pair of pliers to take off the two hoses and clamps. I unplugged the electric connection on each solenoid, took out 5 screws replaced the part and did everything in reverse order. Problem s olved. Thanks for the fast service on my order.
Was this helpful?
Thank you for voting!
OVEN WOULD NOT HEAT
3 of 3 people found this instruction helpful.
  • Mary from MEADVILLE, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN
Was this helpful?
Thank you for voting!
Oven ignighter no longer works
3 of 3 people found this instruction helpful.
  • Barry from PORTERVILLE, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel  t ool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!

Barry
Was this helpful?
Thank you for voting!
Self tapping screws stripped out, one broke in mounting hole
3 of 3 people found this instruction helpful.
  • Scott from FORT WORTH, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.
Was this helpful?
Thank you for voting!
Oven burner would periodically go out and re-light
3 of 4 people found this instruction helpful.
  • Richard from Merrimac, MA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.

Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.
Was this helpful?
Thank you for voting!
Broken hinge on lid
3 of 4 people found this instruction helpful.
  • Charles from NEW LEBANON, OH
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Looked on line for instructions, took my time and the repair went very easy. Just be careful not to drop screws in tub.
Was this helpful?
Thank you for voting!
Oven taking to long to preheat.
3 of 4 people found this instruction helpful.
  • Isaac from LATHRUP VLG, MI
  • Very Easy
  • 30 - 60 mins
  • Screw drivers
Accessed igniter removed 2screws holding it.unpluged igniter installed new one.
Was this helpful?
Thank you for voting!
I had no problems
3 of 4 people found this instruction helpful.
  • Sharron from RICHMOND, TX
  • Really Easy
  • 30 - 60 mins
  • Socket set, Wrench set
I can’t really say it was easy and I just did it
Was this helpful?
Thank you for voting!
Broken hinge part #MEF62462103
3 of 4 people found this instruction helpful.
  • Gerald from CARLSBAD, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
On repair of (replacing one of the MEF62462103 hinges) the previous comments and instructions were good and fairly accurate. However, in addition to having to remove the two screws on the top front so the entire top assemble can be lifted, there are two short screws on the back of the washer towards the top on each side that need to be re moved. That way you can tilt the entire top up enough to get to the two underneath phillips head screws for each hinge. It’s okay to leave all the hoses connected and good to have a second person hold the top tilted up so you can get to the hinge screws. It took about 30 minutes to change one hinge for me and my helper.
Was this helpful?
Thank you for voting!
All Instructions for the 3141
46 - 60 of 312