EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3141 - Instructions

All Instructions for the 3141
91 - 105 of 312

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven would not light reliably.
1 person found this instruction helpful.
  • Joe from West Winfield, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this helpful?
Thank you for voting!
Igniter for oven not working
1 person found this instruction helpful.
  • RONNIE from SAG HARBOR, NY
  • Easy
  • Less than 15 mins
  • Wrench set
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this helpful?
Thank you for voting!
My oven door seal had dried rotted
1 person found this instruction helpful.
  • Anita from ELKTON, VA
  • Really Easy
  • 15 - 30 mins
  • Pliers
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this helpful?
Thank you for voting!
Gas would come on, would not ignite. Oven not heating.
1 person found this instruction helpful.
  • Karen from DAYTON, OH
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Was this helpful?
Thank you for voting!
Washer water would not stop running
1 person found this instruction helpful.
  • Willie from Loganville, GA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Turn water valves off , remove the hoses from washer,remove covering from hose housing, remove the claps from back off housing, remove screws from intake housing, remove iPod intake and install new housing and reverse the install
Was this helpful?
Thank you for voting!
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
1 person found this instruction helpful.
  • FRANCES from AFFTON, MO
  • Very Easy
  • Less than 15 mins
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this helpful?
Thank you for voting!
my knobs were broken on 30 year old range
1 person found this instruction helpful.
  • Larry from LAWTON, MI
  • Very Easy
  • Less than 15 mins
  • Pliers
I took a pair of channel locks pulled the old one off pushed the new one on they look really nice and was glad they had the parts for such an old stove. thank you,now my hubby is glad so he doesn't have to buy a new stove.
Was this helpful?
Thank you for voting!
Plastic hinge broke when closing the washer lid. This piece connects with the slow closing mechanism for the lid.
1 person found this instruction helpful.
  • Larry from Lovettsville, VA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Removed both slow closing latches (3 Phillips head screws each) and lifted off the lid.
Pried off the two plastic caps on the top front of the machine. They are about 1/2" or so in diameter and I used a very thin flat head screwdriver to remove.
Unscrewed the Phillips head screw under each plastic cap.
Popped the two plast ic covers (with the warning labels) off the hinges/closing mechanisms with thin flat head screwdriver.
Pulled dryer out from wall, unplugged the unit from the A/Power, and removed the phillips head screw on each side of the washer back.
Lifted off the washer top with the aid of assistant to hold close to the machine. Be careful with the cable that leads to the control panel.
On the underside of the top, I removed the two Phillips head screws holding the broken hinge and pushed it out from the top.
Replaced the hinge and re-inserted and tightened the two Phillips screws holding it in. Took the opportunity to thoroughly clean the top of the washer tub.
Re-installed the two back and two front screws that hold down the top and popped the two plastic covers on the top.
Moved the lid back into place and slid the slow closing latches back into place and reinstalled the 3 screws in each one. Note how the latch goes back into the hinge. Snapped the two covers back into place.
Plugged in the machine and pushed it back into place.
Lid soft closes perfectly now.
Was this helpful?
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
1 person found this instruction helpful.
  • Mz from COLUMBIA, ME
  • Very Easy
  • Less than 15 mins
  • Pliers
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this helpful?
Thank you for voting!
Oven was slow to get to temp and not holding temp
1 person found this instruction helpful.
  • Matt from Arlington, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.
Was this helpful?
Thank you for voting!
original fixture required bulb - this fixture (all-in-one) was great
1 person found this instruction helpful.
  • wesley from ODENVILLE, AL
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.
Was this helpful?
Thank you for voting!
gas oven would not light
1 person found this instruction helpful.
  • carmine from ABINGTON, PA
  • Very Easy
  • 30 - 60 mins
  • Screw drivers
Remove oven door, remove burner bar, replace ignitor, splice wires together because the old electrical connectors had melted together. Shipping was fast and extra wire, insulation and ceramic wire nuts were included.
Was this helpful?
Thank you for voting!
very dirty under adjitator cap and pulsator
3 of 7 people found this instruction helpful.
  • Daniel from EDWARDS, IL
  • Very Difficult
  • 1- 2 hours
  • Wrench set
Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,
Was this helpful?
Thank you for voting!
Oven was not working at all
1 person found this instruction helpful.
  • Glynne from Dedham, MA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable)
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
Was this helpful?
Thank you for voting!
Replaced upper over light and assembly
1 person found this instruction helpful.
  • Thomas from SAN DIEGO, CA
  • Very Difficult
  • More than 2 hours
  • Pliers, Screw drivers
I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light ass embly from the front of the oven and had to go in from the back.
Was this helpful?
Thank you for voting!
All Instructions for the 3141
91 - 105 of 312