3118 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broke fan blade cleaning unit
1 person
found this instruction helpful.
-
Mark from DEPEW, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Ordered part came in 3 days. Removed plug and rear cover. Pulled off old fan . Installed new fan by pushing it on to shaft. Plugged unit back in to check operation, installed rear cover. Done. Part fit perfect. Thanks to this site you folks are great !
Was this helpful?
Thank you for voting!
Replaced Two Icemakers
2 of 4 people
found this instruction helpful.
-
Melody from Desert Hot Springs, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
We replaced two old icemakers with two new for less than a local repair company wanted to charge us for ONE. Very easy to install, hardest part was cleaning under both refrigerators!
Thanks!
Thanks!
Was this helpful?
Thank you for voting!
icemaker quit working when we moved
4 of 10 people
found this instruction helpful.
-
Regina from Taylorsville, KY
- Really Easy
- 15 - 30 mins
-
Screw drivers
My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After wo
... Read more
rking with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!
Read less
Was this helpful?
Thank you for voting!
Needed new ice maker
1 of 2 people
found this instruction helpful.
-
Carl from Denver, CO
- Really Easy
- 15 - 30 mins
-
Nutdriver
Video is a great but still need to read the instuctions because there are parts you may need on the old ice maker. Saved myself a bit of money by not having to call a repairman. The process was very simple. I am glad I did it myself. Thank you Parts Select!
Was this helpful?
Thank you for voting!
Short in the light socket.
1 of 2 people
found this instruction helpful.
-
ED from ENON, OH
- Very Easy
- Less than 15 mins
Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.
Was this helpful?
Thank you for voting!
broken door shelf bar holder
1 of 2 people
found this instruction helpful.
-
Stan from Dallas, TX
- Really Easy
- Less than 15 mins
I ordered the part before noon and I they had it out the door and in my hands within 24 hours! It took about 2 minutes to take out the broken part and snap in the new one!Great service and easy install!
Was this helpful?
Thank you for voting!
Door shelf clip had broken
1 of 2 people
found this instruction helpful.
-
Erika from Joliet, IL
- Really Easy
- Less than 15 mins
This shelf has been broken for about a year now and my husband tried several little quick fixes that would work for a while and then the shelf would fall again. A quick search online led me to your website, the part arrive within two days, and the shelf was fixed in less than ten minutes. It's working great. We'll definitely keep you in m
... Read more
ind for the future.
Read less
Was this helpful?
Thank you for voting!
Ice maker was not making ice.
1 of 2 people
found this instruction helpful.
-
Tina from Beaumont, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First i removed two screws that holds the ice maker in, unplug the plug to the ice maker. I was able to remove the old one. Place the new one in screwed in the two screws and pluged in the plug and in just a little while i had ice again. I am a women, if i can do it any one can. I had a repair man tell me it was going to be $250.00 dollar
... Read more
s to replace it. I got on line ordered the ice maker and had it in 4 days. Very fast shipping and easy to install. Tina Kearns Beaumont, Calif
Read less
Was this helpful?
Thank you for voting!
The control board generated clicking noise. Temperature display wrong values.
1 of 2 people
found this instruction helpful.
-
QUOC-LOC from LYNN HAVEN, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P ... Read more lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P ... Read more lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Read less
Was this helpful?
Thank you for voting!
A few small ice cubes in an empty try on return from vacation
1 of 2 people
found this instruction helpful.
-
Robert from Loudon, TN
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Look at various pertenant DYI articles and videos on the internet. Replaced water filter with bypass plug. Checked water flow to icemaker water solenoid. Ran icemaker diagnostic test which failed. Ordered replacement. On receipt of replacement, began replacement work. To wit: Pulled fiidge from wall and unplugged. (Not necessary to shut
... Read more
water off.) Removed small freezer basket. Unloaded main freezer basket, removed it then removed the freezer door. (A screw on each side bolts the door rail of the chassis slide to the freezer chassis slide.) Loosened screws on rear, top of partition between icemaker and small freezer basket. Pushed up on partition front and popped out U-bar supporting partition bottom being carefull not to bend it. Removed same. Removed screws from partition and set aside. Removed grilled "thingy" between rear of icemaker and partition. Now have access to icemaker screws. Loosened the screws, pushed up and out and carefully let it hang by it's connector. Fiddled with the connector locking tabs and finally got it loose. Compared old and new icemaker. Have to keep the old water funnel. The new wiring harness was stiff and the connector had a different orientation. Twisted both the wiring harness and connector to align connector while the icemaker hung by it's cable being careful not to let the icemaer slip and fall to the bottom. After much fiddling, got the connector inserted and locked. Set icemaker over the two screws, pulled it down and tightend the screws. Put the old funnel into the new unit being very careful to get it right the first time. Put grilled "thingy and the partition and U-bar back in, put door back on, put the ice cube bin back, freezer drawers bac and reloaded the frozen food, plugged fridge in. Done! Time to replace icemaker was about 20 minutes and another 2 hours to do the rest ofthe work. Still required only a nutdriver and phillips.
Read less
Was this helpful?
Thank you for voting!
Ice maker wouldn't shut off
1 of 2 people
found this instruction helpful.
-
Grant from Black Canyon City, AZ
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
unplug refrigerator. Remove Ice bin then remove the cover off the ice maker,(slides off from bottom then lift off top) no reason to remove ice maker completely. Remove center gear screw and remove main gear from Ejector blade. remove (3) screws holding the front plate. The motor and switches are attached to this plate from behind, do not
... Read more
remove the nut from the from the stud that adjusts the travel for the motor. The Motor and switches will come upt with the plate and the shut off arm will come out of a hole in the top right. Its ok just be careful when you put it back to get it in the hole. remove the old cam and replace it wint the new one and reassemble. Its a bit tricky to get all of the microswitches over the new cam just carefully wiggle the plate and cam and don't push too hard. once everything is lined up it should go back together and you can replace the screws and main gear :)
Read less
Was this helpful?
Thank you for voting!
Instructions did not cover all the parts in kit. The instructions did not cover the elbow in the back of the refg. or the filler tube. I was doing a replacment & it not address that.
2 of 6 people
found this instruction helpful.
-
James from Houston, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I was doing a replacement so it was just a matter of removing old parts and replacingn them with new ones.
Was this helpful?
Thank you for voting!
The ice maker needed replacing for a couple of years. Then, a couple of weeks ago, the water supply stopped serving both the ice maker, and the drink dispenser.
1 of 3 people
found this instruction helpful.
-
Robert from Mahomet, IL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I ordered both a new replacement ice maker, and a new solenoid/pump. They were delivered to my house within one day and I had them installed in a matter of an hour. I had to use the power extension cord supplied with the ice maker.
The new "quick connect" hose couplings on the new pump are great.
The new "quick connect" hose couplings on the new pump are great.
Was this helpful?
Thank you for voting!
Old Ice quit working, would make ice but wouldn't flip ice.
1 of 3 people
found this instruction helpful.
-
Chris from Ulysses, KS
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed old Ice maker and replaced with new Ice maker.
Was this helpful?
Thank you for voting!
socket had melted
1 of 3 people
found this instruction helpful.
-
Chris from Charlotte, NC
- Really Easy
- Less than 15 mins
pluged the wire harness into the new socket from the back and snaped the socket in place.
Was this helpful?
Thank you for voting!