3118 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The above door End Cap broke.
2 of 2 people
found this instruction helpful.
-
John from Northglenn, CO
- Really Easy
- Less than 15 mins
The repair just required snapping the new part on to the door shelf and then snapping the shelf in to the door.
Was this helpful?
Thank you for voting!
Broken shelf retainer bar end cap.
2 of 2 people
found this instruction helpful.
-
Ruchik from Bronx, NY
- Really Easy
- Less than 15 mins
I ordered 2 end caps just to keep one as spare. Turned out I had ordered a size larger than the one already on the refrigerator. So I replaced both ends and it worked fine - with increased shelf space. Now I can even fit a gallon container with ease!!! Took about 20 seconds. I just wish there was an easier way to measure parts before orde
... Read more
ring. Otherwise, the entire process from order to finish took about 3 days.
Read less
Was this helpful?
Thank you for voting!
Cap on the door retainer bar broke.
2 of 2 people
found this instruction helpful.
-
Mary from New Milford, NJ
- Really Easy
- Less than 15 mins
The replacement cap fit perfectly. Unfortunately when the orinigal cap broke it tookout a small piece of the surrounding plastic leaving nothing for the new cap to catch. I have the piece and tried several kinds of glue but nothing holds it securely enough. I would however readily recommend your company. The service was terrific.
... Read more Thank you.
... Read more Thank you.
Read less
Was this helpful?
Thank you for voting!
Not cooling and freezer freezing up
6 of 14 people
found this instruction helpful.
-
kenneth from carmel, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the condenser cover removed old fan blade defrosted the condenser section installed new blade and reassembled
Was this helpful?
Thank you for voting!
light wouldn't come out of socket
3 of 5 people
found this instruction helpful.
-
Joyce from Tacoma, WA
- Really Easy
- Less than 15 mins
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this helpful?
Thank you for voting!
Ice maker
2 of 2 people
found this instruction helpful.
-
Eli from Buford, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove ice maker out of fridge; remove 3 screws
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"
Was this helpful?
Thank you for voting!
Water leaking and freezing everywhere. Weird shaped ice cubes, more like chunks which jambed the dispenser.
3 of 5 people
found this instruction helpful.
-
Peter from Riverdale, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver
First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic
... Read more
door jamb putting the new unit in but other than that all is well and functioning well.
Read less
Was this helpful?
Thank you for voting!
Ice maker stopped working
3 of 5 people
found this instruction helpful.
-
Mary from WESTON, CT
- Very Easy
- Less than 15 mins
-
Nutdriver
Installation could not have been easier!
Was this helpful?
Thank you for voting!
freezer stoped freezing
2 of 2 people
found this instruction helpful.
-
paul from ENDICOTT, NY
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE
... Read more
OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.
Read less
Was this helpful?
Thank you for voting!
The freezer just cool but could not freeze the water and the front of door is quite hot to touch.
2 of 2 people
found this instruction helpful.
-
Fred from FLUSHING, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver
First I observe that the compressor motor is running since the freezer is cooling. The purchase of the condenser fan is initiated and when the part arrive it is just easy to reinstall the replacement condenser fan.
The problem on the front of the freezer door remains hot to touch and the compressor runs for a while and stop. ... Read more The freezer is cold but still could not freeze the water. Inspection of the condenser fan reveals that it is not running. The order for the condenser fan from PARTSELECT came in a few days. Cleaning of the condenser of lint was first done and the process of removing the defective fan is just easy so with the installation.
The refrigerator as of now is running in perfect condition!
The problem on the front of the freezer door remains hot to touch and the compressor runs for a while and stop. ... Read more The freezer is cold but still could not freeze the water. Inspection of the condenser fan reveals that it is not running. The order for the condenser fan from PARTSELECT came in a few days. Cleaning of the condenser of lint was first done and the process of removing the defective fan is just easy so with the installation.
The refrigerator as of now is running in perfect condition!
Read less
Was this helpful?
Thank you for voting!
Ice Maker stopped making ice.
2 of 2 people
found this instruction helpful.
-
Hugh from LADSON, SC
- Really Easy
- 15 - 30 mins
-
Nutdriver
Did the repair just as the instruction said, once I read it. The part I didn't read was that if the plug was under the ice maker, you had to take the wire out of the clip on the side. So, had to dismount ice maker, unclip wire, remount maker, plug it in. Still under 30 minutes. Thank you.
Was this helpful?
Thank you for voting!
The Refridgerator and Freezer were not cooling.
2 of 2 people
found this instruction helpful.
-
Frank from VERO BEACH, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Installing the part repaired the fridge and freezer immediately.
Was this helpful?
Thank you for voting!
icemaker was broken accidentally
3 of 6 people
found this instruction helpful.
-
debi from canfield, OH
- Really Easy
- Less than 15 mins
-
Socket set
First we removed two screws and removed old icemaker- then replaced with the new one~ made ice within the hour. Simple~ Easy~
Was this helpful?
Thank you for voting!
The icemaker quit making ice and the water started forming on the bottom of the ice bucket.
2 of 3 people
found this instruction helpful.
-
John from Anaheim, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts
... Read more
(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.
Read less
Was this helpful?
Thank you for voting!
The plastic parts that hold the brackett to the shelf were broken.
2 of 3 people
found this instruction helpful.
-
Sammy from Farmington, NM
- Really Easy
- Less than 15 mins
The part just snapped into the shelf bar. Extremely easy to fix. Since you show the part in a grid I was able to tell, by holding my old piece up to the screen, that the new part would be the correct size. We have rentals and are always needing parts for appliances. Impossible to find locally.
Also the part came so quickly it was al ... Read more most as good as buying it here in town. Thanks. Donna Bingham
Also the part came so quickly it was al ... Read more most as good as buying it here in town. Thanks. Donna Bingham
Read less
Was this helpful?
Thank you for voting!