3118 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No ice
4 of 5 people
found this instruction helpful.
-
Edward from Kissimmee, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
Ice maker not working. Received my order in 30 hours. (Excellent) After installing ice maker and water valve, I noticed that where the water enters through the freezer to the ice maker spout, there was a frozen spot in the connector. After melting the ice blockage with a hair dryer, the ice maker and water valve began working. No problem
... Read more
since. Unit working perfectly.
Read less
Was this helpful?
Thank you for voting!
My ice breaker started leaking and making noise anf the stripper broke.
4 of 6 people
found this instruction helpful.
-
Marie from Elk Grove Village, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver
I ended up needing to order a new ice maker because the one I had is discontinued. I'm a 65yr old grandma and I did it myself!!!! The hardest part was finding the tool to loosed the nuts. I took the old one out and just put the new one right in it's place. Easy as pie.
Was this helpful?
Thank you for voting!
Ice maker needed replacement
3 of 3 people
found this instruction helpful.
-
James from PLYMOUTH, MA
- Really Easy
- 15 - 30 mins
-
Socket set
Unplug refridge then loosened two bolts holding old ice maker. Lower then unplug and removed. Plugged in new harness and tightened two bolts to secure new ice maker. Plug in frig and wait for ice.
Was this helpful?
Thank you for voting!
Ice maker filled too full and ice froze in the basket and a piece was broke on the icemaker itself.f
3 of 3 people
found this instruction helpful.
-
Karen from SAN ANTONIO, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
My son did it , and showed me what he did when he was finished.
Was this helpful?
Thank you for voting!
Made ice would not eject from ice holder bin
3 of 3 people
found this instruction helpful.
-
Lynn from MOUNTAIN HOME, ID
- Very Easy
- Less than 15 mins
removed broken bin , slid new ice bin in closed door. I bought the complete part.
Was this helpful?
Thank you for voting!
freezer compartment worked fine but very little cooling going to refrigerator section.
3 of 3 people
found this instruction helpful.
-
Lee from OZARK, AR
- Really Easy
- 30 - 60 mins
-
Screw drivers
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The re
... Read more
placement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Read less
Was this helpful?
Thank you for voting!
Ice maker arm disconnected from frame causing problems.
5 of 10 people
found this instruction helpful.
-
Kenneth from Callaway, FL
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker
... Read more
and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.
Read less
Was this helpful?
Thank you for voting!
was not defrosting
3 of 4 people
found this instruction helpful.
-
denis from freedom, NH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
first i removed all the screws inside the freezer compartment took out theback and bottom to get to the evap motor,unpluged the wires and removed the evap motor ,removed the fan from old unit and put it on the new unit them mounted it to the back wall of the fridge,,, and put back top and bottom
Was this helpful?
Thank you for voting!
Ice maker didn't work.
3 of 4 people
found this instruction helpful.
-
Amanda from New Albany, MS
- Easy
- 15 - 30 mins
-
Screw drivers
Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable s
... Read more
hould be more flexible and adapt to the fridge a little more friendly.
Read less
Was this helpful?
Thank you for voting!
icemaker stripper fall a part
3 of 4 people
found this instruction helpful.
-
Ted from Harrisonburg, VA
- Easy
- 15 - 30 mins
-
Screw drivers
instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull"
Dremel and it works!The instalation part of the "job" was less then 10 min.
Dremel and it works!The instalation part of the "job" was less then 10 min.
Was this helpful?
Thank you for voting!
drain freezing up found cond fan not working
3 of 4 people
found this instruction helpful.
-
glenn from la harpe, KS
- Really Easy
- Less than 15 mins
Cleaned oh t freezer removed floor. Removed back inside wall removed and replaced fan and put back removed parts
L
L
Was this helpful?
Thank you for voting!
end cap to bar of freezer door broke
3 of 4 people
found this instruction helpful.
-
Kimberly A from Columbus, OH
- Really Easy
- Less than 15 mins
Snapped end cap onto bar and installed bar onto freezer door.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
Was this helpful?
Thank you for voting!
broken shelf end caps- right side of 2 shelves.
2 of 2 people
found this instruction helpful.
-
William from PRESQUE ISLE, ME
- Really Easy
- Less than 15 mins
After watching video I took off end shelf caps. It took close to 10 mins to replace them.
Was this helpful?
Thank you for voting!
I didn't know if I could get a replacement part, but I googled "replacement parts" (or some such), and since this website looked easy to navigate, chose it. (Actually, I did my ordering via telephone). The sales rep. helped me clarify which part I needed, I ordered it, and received the part the very
2 of 2 people
found this instruction helpful.
-
Kaye from San Francisco, CA
- Really Easy
- Less than 15 mins
I simply snapped the two end pieces into place, attaching the guard rail. It was like putting the pieces of a very easy puzzle together‚ especially for someone like myself who is mechanically challenged.
Was this helpful?
Thank you for voting!
Old end cap broke.
2 of 2 people
found this instruction helpful.
-
Travis from North Quincy, MA
- Really Easy
- Less than 15 mins
Put the new end cap on and snapped it into place, took about 5 seconds.
Was this helpful?
Thank you for voting!